• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.308-308
• /
• 2007

리륨이차전지의 용량의 증가를 위한 연구에 많은 노력과 재원이 투자되고 잇는 반면에, 용량과 성능증가 추세가 주춤한 최근에는 전지의 안전성에 큰 관심이 집중되고 있다. 그 이유는 전지의 성능 못지않게 안전성에 대한 의구심이 꾸준히 제기되고 있고, 대용량 고출력전지의 대표적인 예이 자동차용 전지에는 안전성에 대한 보장이 선결되어야 하기 때문이다. 본 연구에서는 유기 전해액의 발화 및 폭발을 방지할수 있는 방법 중에서 첨가제에 의한 방법을 이용하여 그 첨가제의 전기화학적 특성 및 열적 안정성을 살펴보고 리튬이온전지에의 적용 가능성을 알아보았다. 특히 포스파젠 화합물들을 소량(1~5wt.%)첨가하여, 양극소재의 발열온도를 $60^{\circ}C$ 이상 지연시키고, 사이클 특성의 향상 및 용량의 증가도 실현함으로서 포스파젠 화합물의 유효성을 증명하였다. 아래의 Fig1은 Hexamethoxy cyclo tri-phosphazene(HMTP) 이라는 화합물의 난연성을 표기한 것인데, $270^{\circ}C$ 부근의 background peak가 $340^{\circ}C$까지 지연됨을 보여주고 있다.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.22 no.8
• /
• pp.1183-1194
• /
• 1998

This paper describes a theoretical model developed for analyzing the heat transfer of automotive cooling systems. From the model, heat transfer rate of automotive cooling systems can be predicted, providing useful information at the early stages of the design and development. The aim of the study is to develop a simulation program for automotive cooling system analysis and a performance analysis program for analyzing heat exchanger. Heat release rate from combustion gas to coolant through cylinder wall in engine cylinder was analyzed by using a two zone combustion model. This paper studied how cooling condition would affect engine heat release rate and measured temperature distribution of coolant in water jacket.

• Journal of the Korean Society of Visualization
• /
• v.8 no.1
• /
• pp.25-30
• /
• 2010

The flow characteristics under recirculation cool vent mode is numerically studied using commercial fluid dynamic code(CFX). For the reliable analysis, real vehicle and human FE model is employed in grid generation process. The geometrical location and shape of panel vent, and exhaust vent is set as that of real vehicle model. The flowrate of the working fluid is determined as 330CMH which is equivalent to 70 percent of maximum capacity of HVAC system. The high velocity regions are formed around 4 each panel vent. Because of the non-symmetrically located exhaust, non-uniform flow and partial backflow near the door trim is observed. Streaklines start from each panel vent show the flow pattern of the airflow in the passenger's compartment very well.

• Transactions of the Korean hydrogen and new energy society
• /
• v.13 no.2
• /
• pp.143-150
• /
• 2002

The thermal behavior of $(Co_{0.5}\;Mn_{0.5})Fe_2O_4$ prepared by a co-precipitation wasinvestigated for Hz generation by the thermochemical cycle. The reduction reaction of $(Co_{0.5}\;Mn_{0.5})Fe_2O_4$ started from $480^{\circ}C$, and the weight loss was 1.6 wt% up to $1100^{\circ}C$. At this reaction, $(Co_{0.5}\;Mn_{0.5})Fe_2O_4$ was reduced by release of oxygen bonded with the $Fe^{3+}$ ion in the B site of ($CO_{0.5}$ $(Co_{0.5}\;Mn_{0.5})Fe_2O_4$. In the $H_2O$ decomposition reaction, $H_2$ was generated by oxidationof reduced $(Co_{0.5}\;Mn_{0.5})Fe_2O_4$. The crystal structure of $(Co_{0.5}\;Mn_{0.5})Fe_2O_4$ for reduction reaction maintained spinel structure and the lattice constant of $(Co_{0.5}\;Mn_{0.5})Fe_2O_4$ ($8.41\AA$) was enlarged to $8.45\AA$. But the lattice constant of $(Co_{0.5}\;Mn_{0.5})Fe_2O_4$ after $H_2O$ decomposition reaction did not change to $8.45\AA$. Then, $(Co_{0.5}\;Mn_{0.5})Fe_2O_4$ is excellent material in the thermochemical cyclic reaction due to release oxygen at low temperature for the reduction reaction and produce $H_2$ maintaining crystal structure for redox reaction.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.42 no.6
• /
• pp.787-792
• /
• 2022

In winter, the excessive use of deicing salt deteriorates concrete pavement durability. To reduce the amount of deicing salt used, phase-change materials (PCMs) potentially offer an alternative way to melt snow through their latent heat storage characteristics. In this research, thermal energy storage concrete was developed by using PCM-impregnated expanded clay as 50 % replacement to normal aggregate by volume. In addition, to improve the thermal efficiency of PCM lightweight aggregate (PCM-LWA)-incorporated concrete, multi-walled carbon nanotubes (MWCNTs) were incorporated in proportions of 0.10 %, 0.15 %, and 0.20 % by binder weight. Compressive strength testing and programmed thermal cycling were performed to evaluate the mechanical and thermal responses of the PCM-LWA concrete. Results showed a significant strength reduction of 54 % due to the PCM-LWA; however, the thermal performance of the PCM-LWA concrete was greatly improved with the addition of MWCNTs. Thermal test results showed that 0.10 % MWCNT-incorporated concrete had high thermal fatigue resistance as well as uniform heat flow, whereas specimens with 0.15 % and 0.20 % MWCNT content had a reduced thermal response due to supercooling when the ambient temperature was varied between -5℃ and 10℃.

• Journal of the Korean Electrochemical Society
• /
• v.23 no.3
• /
• pp.57-65
• /
• 2020

It is crucial to investigate the thermal degradation of lithium-ion batteries (LIBs) to understand the possible malfunction at high temperature. Herein, we investigated the effects of surface film formation on the thermal degradation of lithium cobalt oxide (LiCoO₂, LCO) cathode that is one of representative cathode materials. Cycling test at 60℃ exhibited poorer cycleability compared with the cycling at 25℃. Cathodes after the initial 5 cycles at 60℃ (60-LCO) exhibited higher impedance compared to the cathode after initial 5 cycles at 25℃ (25-LCO), resulting in the lower rate capability upon subsequent cycling at 25℃, although the capacity values were similar at the lowest C-rate of 0.1C. In order to understand degradation of the LCO cathode at the high temperature, we analyzed the cathodes surface using X-ray photoelectron spectroscopy (XPS). Among various peaks, intensity of lithium hydroxide (LiOH) increased substantially after the operation at 60℃, and the C-C signal that represents the conductive agent was distinctly lower on 60-LCO compared to 25-LCO. These results pointed to an excessive formation of cathode-electrolyte interphase including LiOH at 60℃, leading to the increase in the resistance and the resultant degradation in the electrochemical performances.

• Journal of the Korean Electrochemical Society
• /
• v.25 no.4
• /
• pp.184-190
• /
• 2022

Spinel LiMn₂O₄ (LMO) and layered LiNi_0.5Co_0.2Mn_0.3O₂ (NCM) are widely used as positive electrode materials for lithium-ion batteries. LMO and NCM positive electrode materials have a complementary properties. LMO has low cost and high safety and NCM materials show a relatively high specific capacity and better cycle life even at elevated temperature. Therefore, the LMO and NCM active materials are blended and used as a positive electrode in large-size batteries for electric vehicles (xEV). In this study, the cycle performance of a blended electrode prepared by simply mixing LMO and NCM and a bi-layer electrode in which two electrode layers aree sequentially coated are compared. The bi-layer electrode prepared by composing the same ratio of both active materials has similar capacity and cycle performance to the blend electrode. However, the LN electrode coated with LMO first and then NCM is the best in the full cell cycle performance at elevated temperature, and the NL electrode, in which NCM is first coated with LMO has a faster capacity degradation than the blended electrode because LMO is mainly located on the top of the electrode adjacent to electrolyte and graphite negative electrode. Also, the LSTA (linear sweep thermmametry) analysis results show that the LN bi-layer electrode in which the LMO is located inside the electrode has good thermal stability.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.6
• /
• pp.126-132
• /
• 2011

Fatigue cracks of the turbocharger are often observed for high performance engines under thermal shock tests. Maximum exhaust gas temperature of recently developed gasoline engines could reach approximately $950^{\circ}C$. It's very important to estimate transient temperature histories during thermal shock cycles to predict the stress and the fatigue life of the turbocharger. With these temperature profiles, temperature-dependent material properties and boundary conditions, we could identify critical locations by the application of finite element simulation technologies. In this paper, we applied the reliable analysis approach to the actual turbocharger to predict the weak locations due to the repetitions of plastic strains and compared the results with the crack locations under physical engine test.

• Polymer(Korea)
• /
• v.37 no.1
• /
• pp.22-27
• /
• 2013

In this study, we prepared separators with improved thermal stability by coating microporous polyethylene (PE) film for lithium secondary battery using poly(meta-phenylene isophthalamide) (Nomex). The mechanical and thermal properties of prepared separators were evaluated by thermal stability test and TMA as a function of the Nomex concentration and coating parameters. The corresponding coated PE separator showed better thermal and mechanical properties than the original PE separator. Electrochemical properties were also assessed by ionic conductivity, cyclic voltammetry and charge/discharge cycle.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.310-310
• /
• 2012

최근 전자산업의 발달에 따른 전자제품의 소형화 및 고기능화 요구에 대응하기 위하여 저항(resistor), 커패시터(capacitor), IC (integrated circuit) 등의 수동소자를 개별 칩(discrete chip) 형태로 형성하여 기판의 표면에 실장하는 기술이 일반화되고 있다. 그러나, 수동 소자의 내장 기술은 기판의 패턴 밀도의 급격한 향상과 더불어 수동소자의 내장 공간도 협소해지는 문제점이 있다. 상기의 문제점을 해결하기 위해 개별 칩 형태의 내장형 저항체를 박막 형태의 내장 저항체를 구현하는 기술의 개발이 최근 주목을 받고 있다. 박막 저항체는 기존의 권선저항 및 후막저항과 비교하여 정밀한 온도저항계수를 가지며 이동통신에 적용시 고주파 영역(GHz)에서의 안정성과 주파수 특성이 좋다는 장점들을 가지고 있다. 박막 저항 물질로는 높은 경도와 우수한 열적 안정성을 가지고 있는 TaN (tantalum nitride)이 주로 사용되고 있다. 일반적으로, TaN 박막은 스퍼터링을 사용하며 제조되며 TaN 박막의 성질은 탄탈륨과 질소의 화학정량비, 박막의 결함 정도, 또는 공정압력 및 증착 온도, 플라즈마 파워 등과 같은 공정조건 등의 변화에 민감하게 변화하므로, TaN 박막의 다양한 연구가 더 필요한 실정이다. 본 연구에서는 반응성 마크네트론 스퍼터링을 사용하여 TaN 박막을 Si 기판 위에 증착하였고 TaN 박막의 원하는 특성을 제어할 수 있도록 질소 분압과 total gas volume을 조절하여 공정을 최적화하는 연구를 진행하였다. 또한 tensile pull-off 방법을 이용하여 TaN 박막의 부착강도를 평가하였고, 온도 사이클 및 고온고습 환경에 노출된 TaN 박막들의 열화 특성들에 대하여 연구하였다.