• Korean Chemical Engineering Research
• /
• v.54 no.5
• /
• pp.687-692
• /
• 2016

Biomass has been concerned as one of the alternative energy resources because it is renewable, abundant worldwide, eco-friendly, and carbon neutral. Quercus variabilis has been studied to understand pyrolysis reaction characteristics, and to evaluate the efficiency of bio-energy production from fast pyrolysis. Quercus variabilis were fast pyrolyzed in a bubbling fluidized bed reactor at various reaction conditions. The effects of pyrolysis temperature between $400^{\circ}C$ and $550^{\circ}C$ on product yields were investigated. The yield of bio-oil was changed between 36.98 wt% and 39.14 wt%, and those of gas yield was 33.40 and 36.96 wt% with increasing reaction temperature. The higher heating value (HHV) of bio-oil at $500^{\circ}C$ ($3.0{\times}U_{mf}$) was 20.18 MJ/kg. The gas compositions were similar for all reaction conditions such as CO, $CO_2$ and $CH_4$, and $CO_2$ selectivity was the highest (37.16~50.94 mol%). The bio-oil has high selectivities for furfural, phenol and their derivatives such as 1-hydroxy-2-propanone, 2-methoxy-phenol, 1,2-benzendiol, 2,6-dimethoxy-phenol.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.9
• /
• pp.436-443
• /
• 2017

Recently, the development of new energy technologies has become a hot topic due to problems,such as global warming. Unlike renewable energy technologies, such as solar energy generation, solar power, and wind power, which are optimized to achieve medium or above output power, the output power of energy harvesting technology is very small and has not received much attention. On the other hand, as the mobile industry has been revitalized recently, the utility of energy harvesting technology has been reevaluated. In addition, the technology of tracking the maximum power point has been actively researched. This paper proposes a new MPPT(Maximum Power Point Tracking) control method for a TEM(thermoelectric module) for load resistance. The V-I curve characteristics and internal resistance of TEM were analyzed and the conventional MPPT control methods were compared. The P&O(Perturbation and Observation) control method is more accurate, but it is less economical than the CV (Constant Voltage)control method because it usestwo sensors to measure the voltage and current source. The CV control method is superior to the P&O control method in economic aspects because it uses only one voltage sensor but the MPP is not matched precisely. In this paper, a method wasdesigned to track the MPP of TEM combining the advantages of the two control method. The proposed MPPT control method wasverified by PSIM simulation and H/W implementation.

• Journal of the Korea Concrete Institute
• /
• v.16 no.4 s.82
• /
• pp.521-528
• /
• 2004

In general, polymer concrete has more excellent mechanical properties and durability than Portland cement concrete, but very sensitive to heat and has large deformations. In this study, the long-term creep behaviors was predicted by the short-term creep test, and then the characteristic of creep of recycled-PET polymer concrete was defined by material and experimental variables. The error in the predicted long-term creep values is less than 5 percent for all polymer concrete systems. The filler carry out an important role to restrict the creep strains of recycled PET Polymer concrete. The creep strain and specific on using the $CaCO_3$ were less than using fly-ash. The creep increases with an increase in the applied stress, but not proportional the rate of stress increase ratio. The creep behavior of polymer concrete using recycled polyester resin is not a linear viscoelastic behavior.

• Journal of Mushroom
• /
• v.8 no.4
• /
• pp.161-164
• /
• 2010

For the development of a sporeless strain of P. ostreatus we used sporeless strain ASI 2069. We have recovered both nuclear types of strain ASI 2069 as monokaryons of nh9, nh15, nh26 and nh36 (here after referred to as neohaplonts) by protoplasting the mycelium. Crosses between neohaplonts and SSI's(single spore isolates) obtained from a sporulating commercial strain ASI 2180. Five excellent strains are selected from 30 bred strains by quality of fruitbodies and spore number. To development of molecular markers linked to sporeless strain of P. ostreatus, we are screened helicase, recombinase(DMC1) and topoisomerase(Spo11) genes related meiosis by PCR and sequencing. Among three genes, Spo11 gene was identified into molecular marker of sporeless from neohaplonts and bred strains of P. ostreatus.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.5 no.2
• /
• pp.106-110
• /
• 1985

This trial was carried out to find out the optimum ridge and seeding rate for the seed production of Festuca arundinacea S. (variety Alta). It was composed of three ridge level (12, 18 and 24cm) and four seeding rates (10, 15, 20 and 25kg/ha) in a split-plot design with 4 replications. The experiment lasted from September 1979 to October 1981. 1. The beginning of heading state was May 12 and the date of full flowering stage was June 2. The optimum stage for the seed harvesting of Festuca arundinacea was about 43 days after beginning of heading stage. 2. The number of panicles were 157 per square meter from the best treatment 18cm ridge with 15kg seed/ha. And the 1000 grain weight was 2.79g for the treatment 12cm ridge with 10kg seed/ha. 3. The average seed yield for two years was 681kg/ha and the largest 831kg/ha for the treatment 18cm ridge with 25kg seed/ha. 4. the average germination rate of the harvested seed was 90.7 percent, and it showed a little higher germination rate from the lower level of seeding rate. 5. The average total DM production with two cuttings of aftermath was about 6715kg/ha. According to the increasing seeding rate and narrowing the ridge, DM yield was higher.

• Journal of the Korean Institute of Gas
• /
• v.21 no.5
• /
• pp.36-44
• /
• 2017

The small commercial fuel cell is a new energy system that produces electricity and heat through electrochemical reaction between air and hydrogen. In Korea, hundreds of domestic small commercial fuel cell systems have been installed and operated every years and many parts in fuel cell systems depend on overseas products. KOGAS(Korea Gas Corporation) has developed the fuel processor which is an important part of fuel cell system and has evaluated the long-term durability. And KOGAS has evaluated domestic and overseas NG blower and fuel processor connected to NG blower. The fuel processor developed by KOGAS have maintained an efficiency of 76% and constant performance over 3,000 hours. The NG blower developed in Korea showed similar characteristics as overseas NG blower in the evaluation of power consumption according to rear pressure and outside temperature. The fuel processor module, fuel processor connected to BOP showed excellent performance.

• Journal of Korean Society of Environmental Engineers
• /
• v.38 no.10
• /
• pp.543-550
• /
• 2016

Amine-type PP-g-VBC-EDA adsorbent, which possesses anionic exchangeable function, was prepared through photoinduced graft polymerization of vinylbenzyl chloride (VBC) onto polypropylene non-woven fabric and subsequent amination reaction using ethylenediamine (EDA). Adsorption characteristics of anionic nutrients on the PP-g-VBC-EDA adsorbent have been studied by batch adsorption experiments. The equilibrium data well fitted the Langmuir isotherm model, and the maximum monolayer sorption capacity was found to be 59.9 mg/g for $NO_3-N$ and 111.4 mg/g for $PO_4-P$. The adsorption energies were higher than 8 kJ/mol indicating anion-exchange process as the primary adsorption mechanism. The pseudo-second order kinetic model described well the kinetic data and resulted in the activation energy of 9.8-36.7 kJ/mol suggesting that the overall rates of $NO_3-N$ and $PO_4-P$ adsorption are controlled by the chemical process. Thermodynamic parameters such as ${\Delta}G^o$, ${\Delta}H^o$ and ${\Delta}S^o$ indicated that the adsorption nature of PP-g-VBC-EDA for anionic nutrients is spontaneous and exothermic. The PP-g-VBC-EDA could be regenerated by washing with 0.1 N HCl.

• Journal of Korean Society of Environmental Engineers
• /
• v.36 no.4
• /
• pp.231-236
• /
• 2014

Sawdust, produced as an wood by-product, is usable biomass as liquid fuels if decomposed to monomer unit, because the chemical structure are similar to high octane materials found in gasoline. In this study, parameters of thermochemical degradation by acetone-solvolysis reaction of sawdust such as the effect of reaction temperature, reaction time and type of solvent on conversion yield and degradation products were investigated. The liquid products by acetone-solvolysis from sawdust produced various kind of ketone, phenol and furan compounds. The optimum sawdust conversion was observed to be 88.7% at $350^{\circ}C$, 40min. Combustion heating value of liquid products from thermochemical conversion processes was as high as 7,824 cal/g. The energy yield and mass yield in acetone-solvolysis of sawdust was 60.8% and 36.4 g-oil/100g-sawdust after 40 min of reaction at $350^{\circ}C$, respectively. The major components of the acetone-solvolysis products, that could be used as liquid fuel, were 4-methyl-3-pentene-2-one, 1,3,5-trimethylbezene, 2,6-dimethyl-2,5-heptadiene-4-one, 3-methyl-2-cyclopenten-1-one as ketone compounds.

• The Korean Journal of Mycology
• /
• v.15 no.2
• /
• pp.80-86
• /
• 1987

The author isolated high cellulolytic fungi from natural sources and determined optimal condition of protoplast formation and fusion as fundamental step for improvement of the isolated it's cellulolytic ability. Three different cellulolytic fungi, such as Aspergillus sp., Penicillium sp. and Trichoderma sp., were isolated from soil. Their cellulolytic activities were compared with that of Aspergillus niger which was useful industrially and had cellulase activity. It was Aspergillus sp. that showed the highest activity of all these four fungi. And then it was followed by Penicillium sp., Trichoderma sp., and Aspergillus niger in order. An auxotrophic mutant of Aspergillus sp. was obtained by UV mutagenesis method. Having try to produce protoplast from mycelia, the author found that ${\beta}-glucuronidase$, at pH 6.0, was effective cell-wall lytic enzyme. And the optimal concentration of this enzyme was 5,000 unit/ml. Regeneration rates of wild type, met. auxotroph and arg. auxotroph, in presence of osmotic stabilizer, were 7. 0%, 7. 5% and 5.2%, respectively. PEG with M.W. 6,000 was effective stimulator for protoplast fusion in the concentration of 30% (W IV). In such a condition, we obtained 1.2% cell fusion rate.

• Journal of the Korean Ceramic Society
• /
• v.40 no.8
• /
• pp.804-810
• /
• 2003

The fine powder produced by heating and grinding of the waste concrete in the waste construction was investigated whether utilize as substitution raw material of SiO$_2$, CaO, and Al$_2$O$_3$ source for OPC clinker manufacture is possible or not. In order to synthesize OPC clinker, limestone, shale, converter slag and fly ash were used as main raw materials, and modulus was fixed LSF 91.0, SM 2.60, IM 1.60. The synthesized clinkers were characterized. The Main products of synthesized clinker were C$_3$S, ${\beta}$-C$_2$S, C$_3$A, C$_4$AF as OPC clinker at 1,43$^{\circ}C$. As a result of TG-DTA and burnability index(B.U) analysis of each raw mixtures, the formation temperature of clinker phases was similar and B.I was showed easy burning as 48.6∼51.4.