• Transactions of the Korean Society of Automotive Engineers
• /
• v.4 no.5
• /
• pp.187-196
• /
• 1996

In this study, 3-dimensional finite element model of a diesel engine cylinder head was made to accomplish heat transfer analysis and also thermal stress and deformation analysis. Heat release analysis and Nusselt-Reynolds correlations were applied to determine the convective boundary conditions which are required for heat transfer analysis to calculate temperature distribution. Thermal stress distribution was also investigated from heat transfer analysis results. Steady state temperature and heat flux were measured by using K-type thermocouples and then compared with numerical results to give a guarantee for the propriety of numerical analyses.

• Journal of Advanced Marine Engineering and Technology
• /
• v.22 no.6
• /
• pp.800-808
• /
• 1998

In this study the thermal stress distribution and deformantion characteristics resulting from the nonuniform temperature fields of the cylinder block of a light 3-cylinder 4-stroke gasoline engine were analyzed using the 3-dimensional finite element method. The temperature distributions req-uisite for the thermoelastic behavior alalysis were obtained from the steady-state heat conduction analysis performed on the basis of experimental data. in order to examine the effect of a ceramic material the cylinder liner was replaced by the silicon nitride($Si_{3}N_{4}$) and its thermal behaviors were compared with those of the original block.

• Journal of Energy Engineering
• /
• v.12 no.3
• /
• pp.177-183
• /
• 2003

The purpose of this paper is to verify that the design stress value of fuel rod for the irradiation test satisfies the structural design requirement. In this structural safety analysis thermal effect is the most severe element for the safety. The thermal effects are very complicated problem to be analyzed for the structural safety in short hand. By the application of theoretical analysis, the design margin of stress which was used in this fuel rod design was verified in the conservative point of view. In the future design of fuel rod, this analysis can be used as the theoretical method for the verification of safe design.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.05a
• /
• pp.42.2-42.2
• /
• 2009

연속주조공정에서 용강의 통로, 산화방지 및 유체 흐름을 용이하게 하는 역할을 하는 다공성 노즐(porous nozzle)은 용강과의 직접적인 접촉으로 인한 화학 반응 및 용강의 침투현상을 방지하기 위해 불활성 가스를 주입하여 청정강을 제조하는데 이용된다. 공정 중 노즐 막힘으로 인한 배압상승과 열충격에 의한 크랙(crack) 발생이 문제되고 있으며 신뢰성 향상 연구가 요구되고 있다. 따라서 본 연구에서는 기공크기와 기공분포가 고온안정성 및 내열충격성에 미치는 영향을 알아보고, 내구성 시험 및 고장분석을 통하여 노즐의 신뢰성 향상 방안을 고찰 하였다. 기공을 제어한 시편을 제조하여 기공분포에 따른 고온안정성을 확인하기 위해 실제 사용 조건인 용강온도($1550^{\circ}C$)와 보다 높은 온도($1700^{\circ}C$)에서 각각 고온 시험을 수행하였다. 열충격을 스트레스 인자로 한 내구성 시험을 수행한 후 고장원인을 분석하였으며 열화정도를 확인하기 위해 열처리 온도에 따른 차압 및 굽힘 강도 변화를 비교하였다. 또한 결정상 분석을 통해 온도에 대한 상변화를 확인하였고, 시편의 표면 및 파단면의 미세구조 분석을 통해 크랙 발생여부를 확인하였다. 다공성 노즐의 기공분포가 균일 할수록 고온안정성 및 내열충격성이 향상됨을 확인하였고, 이를 통해 Porous Nozzle의 열화원인으로 판단되는 기공 크기 및 분포에 따른 크랙 발생에 대해 열응력 고찰을 수행하였다.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.25 no.6
• /
• pp.505-512
• /
• 2012

In this paper, an efficient yet accurate method for the thermal stress analysis using a first order shear deformation theory(FSDT) is presented. The main objective herein is to systematically modify transverse shear strain energy through the mixed variational theorem(MVT). In the mixed formulation, independent transverse shear stresses are taken from the efficient higher-order zigzag plate theory, and the in-plane displacements are assumed to be those of the FSDT. Moreover, a smooth parabolic distribution through the thickness is assumed in the transverse normal displacement field in order to consider a transverse normal deformation. The resulting strain energy expression is referred to as an enhanced first order shear deformation theory, which is obtained via the mixed variational theorem with transverse normal deformation effect(EFSDTM_TN). The EFSDTM_TN has the same computational advantage as the FSDT_TN(FSDT with transverse normal deformation effect) does, which allows us to improve the through-the-thickness distributions of displacements and stresses via the recovery procedure. The thermal stresses obtained by the present theory are compared with those of the FSDT_TN and three-dimensional elasticity.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.2
• /
• pp.177-184
• /
• 2014

In this study, we investigated the variations in welding residual stresses in dissimilar metal butt weld due to width of repair welding and re-distribution behaviors resulting from similar metal welding (SMW) and mechanical loading. To this end, detailed two-dimensional axi-symmetric finite element (FE) analyses were performed considering five different repair welding widths. Based on the FE results, we first evaluated the welding residual stress distributions in repair welding. We then investigated the re-distribution behaviors of the residual stresses due to SMW and mechanical loads. It is revealed that large tensile welding residual stresses take place in the inner surface and that its distribution is affected, provided repair welding width is larger than certain value. The welding residual stresses resulting from repair welding are remarkably reduced due to SMW and mechanical loading, regardless of the width of the repair welding.

• Composites Research
• /
• v.15 no.1
• /
• pp.41-52
• /
• 2002

This paper presents the thermo-elastic analysis for searching the behavior of carbon/carbon brake system during the braking period and the 3-D stress analysis to find the shape of the brake disk which is safe to the failure. The mechanical properties of the carbon/carbon brake disk were measured for both in-plane and out of plane directions. The mechanical properties were used as the input of the thermo-elastic analysis and 3-dimensional stress analysis for the brake disk. The gap between rotor clip and clip retainer is an important parameter in the loading transfer mechanism of the rotor disk. The change of gap was considered both the mechanical deformation and thermal deformation. Because the rotor clip and clip retainers were not contacted, they were excluded from the analysis model. Rotor disk was modeled by using the cyclic symmetry condition. The contact problems between rotor clip and key drum as well as between rotor disk and rotor were considered. From the results of the 3-D stress analysis, the stress concentration at the key hole of the brake disk was confirmed. The stress distributions were studied thor the variation of the rotation angle of the contact surface and the radius of curvature at the key hole part.

• Journal of the Korean Vacuum Society
• /
• v.7 no.4
• /
• pp.285-292
• /
• 1998

The vacuum vessel of the KSTAR tokamak has a so large poloidal cross- section that workers can enter into the inside the vessel. To produce a clean plasma with low impurity concentrations it is planned that the whole vessel including plasma facing components will be baked out at $350^{\circ}C$ and the base pressure of the vessel will be kept in the range of ultra high vacuum. Large thermal stresses are expected during bake-outs to a three-dimensionally complex structure of the vessel, consequent ununiformity of the temperature distribution and support systems to resist forces acting on the vessel. In this report variations of the thermal stress according to temperature gradients on the vessel and constraint conditions of supporting structures are studied and some possible counterplans are discussed.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.210-213
• /
• 2002

The Purpose of this study is to know temperature and thermal stress distribution in specimens during processing of WEDM. If it is constant to the cutting speed and the thickness of material, it is very important to the effect of temperature and the thermal stress distribution after cutting processing. This paper show the analysis result of the distribution of temperature and the residual stress along the direction of thickness before processing of WEDM and after when the cooling temperature is$20^{\circ}C$. The maximum temperature of edge of specimens is $1600^{\circ}C$. It has little temperature gradient in the depth which is 5mm away from edge of specimens. Equivalent residual stress is result in 180.7 MPa at maximum temperature.

• Proceedings of the KWS Conference
• /
• 2010.05a
• /
• pp.55-55
• /
• 2010

마그네슘 판재는 경량화 소재로 주목받는 소재이다. 본 연구는 압연 마그네슘 판재의 용접시 발생하는 온도이력 및 응력에 대한 해석을 수행하였다. 해석은 2차원 해석을 수행하였으며 해석수행에 있어서 열물성값은 기존의 데이터를 이용하였으며 응력해석은 온도별 고온 인장시험을 수행한 결과를 이용하여 해석을 수행하였다. 본 연구에서 수행한 대상은 마그네슘 압연판재인 AZ31B 이며 두께 3.5 mm 판재를 GTAW용접을 수행한 경우에 대하여 검토하였으며, 해석결과 중 온도분포의 한 예를 그림 1에 나타낸다.