• 한국음향학회지
• /
• 제9권2호
• /
• pp.14-24
• /
• 1990

본 논문에서는 열박음 부분을 모델링하여 그 부분에서의 단위길이당 스프링강성을 산정한다음 전달매트릭스를 구하였다. 여기에 MYKLESTAD 방법을 토대로 하여 축의 전달매트릭스를 구하였다. 열박음축에 대해서는 수축공차에 따른 고유진동수를 구하였으며, 열박음효과의 효율성을 위하여 똑같은 크기의 열박음 하지 않은 축과 비교검토 하였으며 이를 실험으로 검토하였다. 연구결과 수축공자가 커지면 커질수록 단위길이당 스프링강성은 증가 하였고 고유진동수도 증가하였다. 그리고 열박음축은 열박음 하지 않은 축보다 고유진동수가 감소하였다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 추계학술대회 논문집
• /
• pp.119-123
• /
• 2009

In this paper, effects of major design parameters of cold forging dies on die mechanics are quantitatively investigated with emphasis on shrink fit using a thermoelastic finite element method. A ball-stud cold forging process found in a cold forging company is selected as a test process and the effects of die insert material, shrink fit, dimension of ring, partition of die inert and clamping force on effective stress and circumferential stress are analyzed.

• 한국정밀공학회지
• /
• 제18권3호
• /
• pp.40-46
• /
• 2001

An integrated analysis for the thermo-elastic deformation, fatigue, wear and brittle damage evolution of the shrink-fitted die with multi stress-ring of dissimilar materials is presented. A simple numerical algorithm for the moving elastic boundaries characterizing the contacts of the insert and multi stress-rings is presented. The initial stress distribution in the die due to shrink-fit is considered and the traction at the die surface contacting with the work piece is obtained by analyzing the elasto-plastic deformation of work piece. Elastic analysis of the separate-type die is performed and then the evolution of brittle damage, wear and fatigue life are predicted. This integrated analysis is applied to the extrusion die with two layers of stress-rings and the results are discussed in detail.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집A
• /
• pp.848-853
• /
• 2001

A study about the shrink fits of rotor and retaining ring in generator was performed for the cases of three radial interference. The shrink-fitted retaining ring used to restrain the end turns of the winded coils in the rotor against centrifugal force requires very careful attention during design and manufacture because it has traditionally been the highest-stressed component of the generator. The contact pressures and residual stresses were obtained by the finite element analysis for each radial interference at zero, 100% rated, and 120% rated speeds, respectively. The results of analysis show that the radial interference in use needs to be increased carefully.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집A
• /
• pp.849-853
• /
• 2000

The retaining rings used to restrain the end turns of the rotor winding against centrifugal force require very careful attention during design and manufacture because they have traditionally been the highest-stressed components of the generator. In other words, the rings maintain their shrink fits during their entire service life. In this study, using finite element method, the part of shrink fits in generator was analyzed to obtain residual stresses in retaining ring and contact Pressures between contact surfaces at zero, rated, and 120 rated speeds, respectively.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2008년도 추계학술대회논문집
• /
• pp.210-211
• /
• 2008

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2000년도 특별강연 및 추계학술발표대회 개요집
• /
• pp.127-130
• /
• 2000

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2009년도 추계학술대회 논문집
• /
• pp.575-576
• /
• 2009

• 대한기계학회논문집A
• /
• 제33권9호
• /
• pp.963-968
• /
• 2009

This paper deals with shrink fit analysis of rotor by 2D cross-section, 2D axis-symmetry, and 3D FEM model. And this paper presents 2nd order approximation function of thermal expansion displacement by design variables (shape dimension, heating temperature, sleeve length, interference etc.), table of orthogonal array and RSM(response surface methodology). The possibility of the rotor with shrink fit is evaluated by thermal expansion displacement. If thermal expansion displacement is larger than interference, shrink fit enable to make the rotor. 2D axis-symmetry model and 3D model are more reasonable than 2D cross-section model, because stress and strain is different along length of shaft.

• 한국정밀공학회지
• /
• 제28권3호
• /
• pp.301-307
• /
• 2011

In this paper, effects of major design parameters of cold forging dies on die mechanics are quantitatively investigated with emphasis on shrink fit using a thermoelastic finite element method. A ball-stud cold forging process found in a cold forging company is selected as a test process and the effects of die insert material, magnitude of shrink fit, dimension of shrink ring, number of shrink rings, partition of die insert and clamping force on effective stress and circumferential stress are analyzed. It has shown that the number of shrink rings, magnitude of shrink fit, and Young's modulus of die insert material have strong influence on compressive circumferential stress in die insert but that the influence of the other design parameters is relatively weak.