Suh, Chang Hee;Park, Myung Kyu;Park, Jong Kyu;Kim, Young Suk
Transactions of the Korean Society of Mechanical Engineers A
/
v.37
no.3
/
pp.339-344
/
2013
Hot forming using boron steel is currently used for manufacturing low-weight automobile body parts, and a high tensile strength of about 1,500 MPa is obtained after hot forming. However, a high fatigue life is a more important factor than high strength when it is used for automobile suspension parts. A tubular torsion beam axle (TTBA) is one of these suspension parts, and this research deals with the fatigue characteristic of TTBA using hot forming. The low cyclic fatigue life of boron steel is investigated according to the cooling method. In addition, a structural and fatigue analysis of TTBA is performed to predict the fatigue life. The stress concentration that occurs in the tubular torsion beam is found, and the longest fatigue life occurs when rapid cooling is utilized in the TTBA fabrication.
Transactions of the Korean Society of Mechanical Engineers A
/
v.34
no.10
/
pp.1419-1425
/
2010
Boron steel sheet is suitable for fabricating automobile parts because it is very strong and has low weight. Recently, many car makers are investigating the feasibility of fabricating the chassis part of automobiles using boron steel. In order to use boron steel sheets to fabricate the chassis part of automobiles, much better material property of low cycle fatigue life as well as high formability during hot stamping is required. Therefore, the low-cycle fatigue life of hot-stamped quenched boron steel was investigated in this study. The fatigue life observed at low strain amplitude was longer than that of an as-received boron steel sheet. However, the fatigue life reduced at high strain amplitude because of the low ductility and low fracture toughness of martensite, which was produced as a result of hot stamping.
Proceedings of the Korean Society of Propulsion Engineers Conference
/
2000.04a
/
pp.39-39
/
2000
열간단조후 절삭가공하여 냉간 성형가공하는 알루미늄 제품은 열간단조하면 재료가 연화되어 있어 절삭가공시 연속적인 칩이 발생하여 공구와 피삭재를 감고 회전함으로서 가공면 손상, 공구파손 및 작업자의 안전을 초래함에 따라 가공이 어려워 단지 절삭성 개선 목적만을 위해 중간공정으로 T4 열처리하여 절삭가공하고 다시 어닐링처리하여 냉간성형을 하고 최종열처리를 한다. 따라서 본 연구는 열간단조후 제품을 급냉시키면 용제화처리의 효과를 얻어 재료가 경화됨으로써 절삭성이 개선될 수 있다는 이론에 근거하여 T4 열처리를 대체할 수 있는 후처리 방법에 대해 연구하였다. 최적의 후처리방법을 구하기 위해 열간단조후 수냉과 공냉처리를 비교 분석하였고, 열간단조후 냉각처리까지 지연된 시간과 수냉과정에서의 유지시간에 따른 분석을 통해 최적의 작업조건을 선정하였다.
Proceedings of the Materials Research Society of Korea Conference
/
2003.03a
/
pp.144-144
/
2003
니켈계 내열합금의 성형은 수백 $^{\circ}C$에 이르는 고온에서 이루어지기 때문에 열간성형 과정에서 소재 내부의 미세조직 변화에 대한 이해는 부품의 특성 제어 측면에서 매우 중요하다. 특히 열간 동적 재결정에 의해 발생되는 결정립 구조의 변화를 적절히 조절함으로써 부품의 특성을 극대화 할 수 있다. 본 연구에서는 Ni-Fe계 초내열합금에 대한 고온 압축실험과 압축시편에 대한 EBSD 분석을 통해 열간 변형 과정에서 발생하는 소재 내부의 동적인 결정립 구조의 변화를 정량적으로 분석하고자 하였다. 고온 압축시험은 101$0^{\circ}C$, 1066$^{\circ}C$의 온도 조건과 0.5s-1, 0.005s-1의 변형율 속도 조건에서 최대 진변형율 0.7까지 수행하였으며 진변형율에 따른 결정립 조직 변화를 관찰하기 위해 진변형 율에도 변화를 주어 실험을 수행하였다. 이들 고온 압축시편은 응력방향에 평행한 면에 대한 미세조직 관찰을 통해 재결정립 크기, 분율 및 결정립계의 특성 변화에 대한 정량적 연구를 수행하였다.
Transactions of the Korean Society of Mechanical Engineers A
/
v.37
no.4
/
pp.483-490
/
2013
In aluminum sheet metal forming, the conventional forming methods of T4 or T6 heat-treated sheets result in low formability and dimensional accuracy. This study suggests a new forming method for aluminum sheets called as hot forming quenching (HFQ) that solves the problems faced in the conventional method. HFQ combines the heat treatment and forming processes through the forming die during the quenching of a solid solution. To evaluate the application of HFQ to the sheet forming of aluminum, an Erichsen and V-bending test are performed in this study to measure the dimensional accuracy and formability, which are then compared with those of the conventional forming method. Furthermore, the strength and hardness of the products formed by HFQ are measured to confirm the degradation in mechanical properties compared with the conventional forming method, which shows the validity of the application of HFQ to aluminum sheet metal forming.
Transactions of the Korean Society of Mechanical Engineers A
/
v.37
no.4
/
pp.547-554
/
2013
The fuel storage vessel installed in CNG vehicles can be largely divided into 3 parts: head, cylinder, and dome. Studies of the cylinder and dome parts have already been performed, but sufficient design data is not available about the head part. Therefore, expert field engineers heavily depend upon trial-and-error methods. Therefore, FE analysis is performed to review the hot spinning process for forming the head part of the CNG vessel using the Arbitrary Lagrangian-Eulerian (ALE) method. The effects of forming factors on the load were analyzed. The values of the factors were chosen to avoid defects in the head part and buckling, and the forming feasibility of the head part was investigated. Furthermore, a bursting test was performed to evaluate the safety of the storage vessel.
Powder metallurgy has been employed for the development of SiC particle reinforced aluminum metal matrix composites by means of hot isotropic pressing and vacuum hot pressing. A material model based on micro-mechanical approach then has been presented for the processes. Densification occurs by the inelastic flow of matrix materials during the consolidation, and consequently it depends on many process conditions such as applied pressure, temperature and volume fraction of reinforcement. The model is implemented into finite element software so that the process simulation can be performed enabling the predicted relative density to be compared with experimental data. In order to determine the performance of finished products, further tensile test has been conducted using the developed specimens. The effect of internal void of the materials on mechanical properties therefore can be investigated.
Proceedings of the Korea Inteligent Information System Society Conference
/
2007.11a
/
pp.570-578
/
2007
선체 외판 부재의 곡 성형 과정은 주로 가열(열간가공)에 의해 수행된다. 이 가열 작업은 작업자의 경험과 지식에 크게 의존하는 매우 어려운 작업이다. 본 논문에서는 선체 외판의 곡 성형을 위한 가열 계획을 자동으로 수립할 수 있는 휴리스틱을 소개한다. 현장 전문가의 지식에 기반한 이 휴리스틱은 크게 가열 선을 생성하는 부분과 외력을 주는 도구를 배치하는 부분으로 구성된다. 가열 선은 대상 부재의 현재 곡면과 설계된 목적곡면과의 비교를 통해 생성되고, 가우스 커널 함수를 통해 스무딩(smoothing)된다. 현장에서는 열간가공 시 의도하지 않은 변형을 막으면서 작업시간을 줄이고자 외력을 이용한다. 외력의 위치와 방향은 가열 선 군집화를 통해 추출된 대표 가열 선을 기준으로 결정된다. 가상의 인공 곡면과 현장의 실제 부재를 대상으로 실험한 결과, 이 휴리스틱이 숙련된 전문가가 수립한 가열 계획과 유사한 가열 계획을 수립할 수 있음을 확인하였다.
Proceedings of the Korean Society of Propulsion Engineers Conference
/
1998.10a
/
pp.17-17
/
1998
1970년대에 개발된 Ti-15-3 합금은 상온에서 우수한 성형성을 가지고 있어 Ti-6-4 합금보다 성형 공정을 대폭 감소시킬 수 있어 생산비용을 크게 감소시킬 수 있는 장점이 있는 합금이다. 또한, 냉간 성형성이 우수하고 강화 범위가 폭넓기 때문에 항공기의 프레임, 항공기 압력 용기 및 고장력 유압 튜브 등에 많이 사용하고 있으나, 열간 성형성이 Ti-6-4 티타늄 합금보다 좋지 않기 때문에 이제까지의 적용 분야는 판재 성형 등의 한정된 분야에만 적용되어 오고 있는 실정이다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.