저온 환경에서 사용하는 장치의 급격한 개발 요구에 따라 내한성을 가지는 케이블 재료에 대한 요구도 급격하게 증가하고 있다. 열가소성 폴리머는 폴리머를 구성하는 약 20개 이상의 첨가제와 폴리머의 종류와 함량에 따라 내한특성이 크게 좌우된다. 저온에서의 고분자 경화현상은 단순 온도에 의한 효과와 유리 전이온도에서의 취화 및 경화, 고분자의 결정화에 의한 경화로 구분할 수 있다. 본 연구에서는 저온의 유리 전이온도를 가지는 열가소성 폴리머와 난연제 및 첨가제 등을 혼합하여 전선용 열가소성 고분자 복합재료의 기계적 특성 평가를 하였다. 첨가제와 상용화제의 첨가량에 따라 기계적 물성과 가공성 등이 결정되는 것을 확인하였고 본 연구는 저온용으로 개발하는 전선 요구성능 충족을 위한 최적화의 기초 데이터로 활용할 수 있을 것으로 사료된다.
열가소성 복합재료는 다양한 장점에도 불구하고 기계적 특성이 낮아 고성능 항공산업 분야에서는 제한적으로 사용되어 왔으나 최근 열가소성 방향족 폴리머 복합재들이 많이 연구/활용되고 있다. 본 연구에서는 대표적인 열가소성 방향족 폴리머인 PEEK와 PPS Neat 수지 필름을 DSC 기기를 이용하여 가열, 냉각 및 재 가열 사이클을 연속적으로 수행하여 유리전이온도 및 용융온도 등의 특성변화를 확인하고 냉각속도에 따른 결정화도(Crystallinity)의 차이를 평가하였다. 1차 가열단계에서 각 폴리머의 용융온도보다 높은 온도에 5분간 유지시켜 이전 열이력을 제거하였고 2차 냉각단계에서 냉각속도를 분당 2, 5, 10, 20 및 $40^{\circ}C$로 조절/적용함으로서 결정화반응을 제어하였으며, 3차 가열단계에서 재가열하여 용융엔탈피를 측정함으로서 결정화도 차이를 확인하였다. 높은 비정질 영역을 가진 시편의 첫 번째 가열시 냉각결정화 현상이 일어나고 뚜렷한 유리상 전이구역을 확인할 수 있었던 반면에 결정질 영역이 증가된 재가열시에는 냉각결정화 현상이 일어나지 않고 상대적으로 유리상 전이구역이 약해지는 것을 확인하였다. 2차 냉각단계에서 냉각속도가 느려짐에 따라 결정화도가 높아졌는데 PEEK의 경우 냉각속도의 차이에 따라 21.9~39.3% 결정화도를 보였으며, PPS는 29.1~31.2% 결정화도 차이를 얻을 수 있었다.
기존의 가열식 일반아스팔트 공법은 동결 등에 원인으로 포장재의 수명이 짧아져 잦은 유지보수가 필요한 문제점을 갖고 있으며, 이로 인해 내구성이 뛰어난 포장공법의 필요성이 대두되고 있다. 불투수성 방수아스팔트는 이러한 문제를 해결하기 위한 방안의 하나로 아스팔트 혼합물이 골재와 골재 사이를 강력하게 부착하며, 골재간의 공간을 메우고, 골재표면을 두껍게 코팅하여 골재 상호간의 강한 접착을 유지시켜주는 열가소성 폴리머를 사용한 포장공법이다. 본 연구는 불투수성 방수아스팔트 혼합물 개발을 위한 연구의 일환으로 석회석함유량, 유제함유량, 다짐강도, 실험온도 차이에 따른 불투수성 방수아스팔트 혼합물의 압축강도 특성을 실험을 통해 비교 검토하였다. 결과 분석을 통해 각각의 변수에 따른 압축강도 특성을 파악하였으며, 불투수성 방수아스팔트 혼합물 배합설계에 기초자료로 활용하고자 한다.
Thermoplastic fusion bonding is widely used to seal polymer microfluidic devices and optimal bonding protocol is required to obtain a successful bonding, strong bonding force without channel deformation. Besides, UV modification of the PMMA (poly-methyl methacrylate) is commonly used for chemical or biological application before the bonding process. However, study of thermal bonding for the UV modified PMMA was not reported yet. Unlike pristine PMMA, the optimal bonding parameters of the UV modified PMMA were $103^{\circ}C$, 71 kPa, and 35 minutes. A very low aspect ratio micro channel (AR=1:100, $20{\mu}m$ depth and $2000{\mu}m$ width) was successfully bonded (over 95%, n>100). Moreover, thermal bonding of multi stack PMMA chips was successfully demonstrated in this study. The results may applicable to fabricate a complex 3 dimensional microchannel networks.
Adhesion tests were carried out in order to investigate the effect of temperature on the adhesion behavior between a PMMA film and a fused silica lens in the micro scale. For the tests, a microtribometer system was specially designed and constructed. The pull-off forces on the PMMA film were measured under atmospheric condition as the temperature of the PMMA film was increased from 300 K to 443 K and decreased to 300 K. The contact area between the PMMA film and the lens was observed during the test. The adhesion behavior was changed with the change of the PMMA surface state as the temperature increased. In glassy state below 363 K, the pull-off force did not change with the increase of temperature. In rubbery state from 383 K to 413 K, the pull-off force increased greatly as the temperature increased. In addition, the area of contact was enlarged. In viscous state above 423 K, the fingering instability was observed in the area of contact when the PMMA film contacted with the lens. It was also found that the adhesion behavior can be varied with the thermal history of the PMMA film. The residual solvent in the PMMA film could emerge to the PMMA surface due to the heating and reduced the pull-off force.
Friction tests were carried out in order to investigate the effects of temperature on the friction and wear behaviors between a PMMA film and a fused silica lens using a microtribometer. The friction forces on the PMMA film were measured under atmospheric condition as the temperature of the film was increased from 300 K to 443 K. The contact area between the film and the lens was observed. The tribological characteristics of the film were significantly changed as the temperature increased. The changes were discussed with the change of the film state from glassy to viscous flow. In addition, the results showed that the friction behavior can be varied with the thermal history of the PMMA film. Residual solvent in the PMMA film could emerge to the PMMA surface due to an additional heating and the solvent on the film surface decreased the friction force.
열경화성 탄소 섬유 복합재료 분리판은 높은 기계적 특성뿐만 아니라 높은 내산성을 갖으나, 높은 제조단가 및 낮은 자체저항이 극복해야 할 가장 큰 장애물이다. 따라서 본 연구에서는, 열가소성 폴리머를 복합재료 분리판의 기지로 적용하여 분리판 생산성과 자체저항이 모두 증가된 열가소성 탄소 복합재료 분리판을 개발하였다. 전기 전도도 및 기계 강도를 증가시기키 위하여 평직 형태의 탄소 섬유 직물을 사용하였으며, 분리판의 자체 저항을 감소시키기 위하여 전도성 나노입자를 열가소성 기지에 혼합하였다. 개발된 분리판의 면적 비저항 및 기계물성을 고온 연료전지 작동 온도 및 스택의 체결압에 따라 측정하였다.
모든 고체로켓 추진제들은 화학적 상태에 따라 균질(복기)과 비균질(혼합형)의 2가지 기본 종류로 나뉜다. 오늘날 혼합형 추진제는 가스발생기와 소형 로켓으로부터 우주개발을 위한 거대 발사체까지 동력원으로써 광범위하게 사용된다. 과거에 혼합형 로켓 추진제의 개발은 주로 열경화성 폴리머에 국한되었다. 그러나 열경화성 혼합형 추진제는 로켓 체계조건에 부합하기 위해 조성과 제조공정에 있어 복잡성을 갖는다. 열경화성 추진제와 대조해서, 개량된 PVC 및 TPE 계열 열가소성 추진제는 중간 정도의 성능과 기계적 성질을 갖지만 제조공정에서의 손실, 원재료의 저가와 취급 공정의 안정성을 갖는다. 이런 장점으로 인해 향후, 열가소성 추진제가 여타 추진제보다 폭넓게 사용될 것이라 예측된다.
경제성과 가공 시 용이성 등의 장점을 가지는 합성수지는 자연상태에서 분해되지 않고 환경오염을 야기 시키는 문제를 가진다. 이러한 문제를 해결하기 위해 재활용이 가능한 열가소성 수지가 주목되고 있고 그 중 경제성이 뛰어난 폴리프로필렌(PP)에 대한 관심이 높아지고 있다. PP의 경우 기계적 특성 및 열안정성 등과 재활용성이 뛰어나다. 하지만 다수의 문헌에서 열가소성 수지의 반복 가공에 따라 물성의 저하가 일어난다는 것을 확인 할 수 있으며 가공 조건에 따라 품질의 저하가 발생하는 시점이 다르다는 것을 확인할 수 있다. 따라서 본 연구에서는 PP 수지에 여러 첨가 성분을 블렌딩하여 복합 조성물 제조 시 반복 공정에 의한 성능 변화를 평가하기 위해 압출 공정 및 사출 공정을 반복 진행하여 기계적 특성 및 열적 특성을 평가하고자 한다. 또한 반복 공정 시 MFI 값 변화에 따라 복합재료 공정 시 섬유의 함침에 어떤 영향을 주는지에 대해 평가하기 위해 복합재료의 기계적 물성을 평가하고자 한다.
Adhesion tests were conducted to investigate the adhesion characteristics between mold and thermoplastic polymer film. Coating of anti-sticking layer (ASL), a kind of polymer material, imprint pressure, and separation velocity were considered as the process conditions. A piece of fused silica without patterns on its surface was used as a mold and the thermoplastic polymer films were made on Si substrate by spin-coating the commercial polymer solution such as mr-I PMMA and mr-I 7020. The ASL was derived from (1H, 1H, 2H, 2H - perfluorooctyl) trichlorosilane($F_{13}$-OTS) and coated on the fused silica mold in vapor phase. The pull-off force was measured in various process conditions and the surfaces of the mold and the polymer film were observed after separation. It was found that the adhesion characteristics between the mold and the thermoplastic polymer film and the release performance of ASL were changed according to the process conditions. The ASL was effective to reduce the pull-off force and the damage of polymer film. In cases of the mold coated with ASL, the pull-off force did not depend on imprint pressure and separation velocity.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.