• Proceedings of the Korea Water Resources Association Conference
• /
• 2016.05a
• /
• pp.70-70
• /
• 2016

하천시설물 설계, 시공 및 관리에 있어서 바닥전단응력은 매우 중요하다. 예를 들어, 호안 등 시설물의 허용 소류력을 계산하거나, 하천의 유사량을 예측하는 데 있어서 바닥전단응력이 기준으로 쓰인다. 정상 등류의 경우, 수로 내 수체에 작용하는 중력과 수로 바닥 및 측면에 작용하는 마찰력의 평형을 고려함으로써 바닥전단응력을 산정할 수 있다. 본 연구에서는 식생을 제외한 아크릴수로에서의 전단판의 움직임을 이용한 바닥전단응력 측정장치를 설계, 교정 및 검증을 실시하였다. 이 전단판은 수체와 바닥면에서 발생하는 마찰력에 의해 변위가 발생하고 이 변위를 바닥전단 응력으로 산정하였다. 직접 측정한 바닥전단응력은 기존에 연구된 두 가지 방법과 비교하여 검증하였다. 비교 검증을 위한 실험은 폭 0.3 m, 길이 10 m인 고속수로에서 Froude수 1이상, Reynolds수 20000이상의 사류이면서 난류인 상태로 실험을 진행하였으며 유속은 PIV을 이용하여 측정하였다. 비교 검증을 위한 첫 번째방법은 Reach-avrage공식을 기초로 manning의 평균 유속 공식을 이용한 바닥전단응력을 산정하는 방법으로 일반적으로 간단한 경험식을 이용하여 바닥 전단응력을 산정하는 방법이다, 두 번째는 Reynolds stress를 산정하는 방법으로 PIV를 통해 흐름방향의 연직프로파일의 유속을 측정 한 후 레이놀즈 분해법에 의해 산정된 난류 강도를 측정하여 Reynolds stress를 산정한 후 Shear stress를 산정하는 방법을 사용하였다. 마지막으로 본 연구에서 가로 0.14 m, 세로 0.14 m의 전단판으로 구성된 바닥전단응력 측정장치를 개발하여 실험을 진행하면서 앞에서 언급한 두가지 방법을 측정하는 동시에 장치를 이용하여 바닥전단응력을 직접측정하여 총 3가지 바닥전단응력을 비교하였다.

• Journal of Korean Society of Disaster and Security
• /
• v.11 no.2
• /
• pp.61-67
• /
• 2018

Scour protection methods can be categorized as two types: The first is to reduce the horseshoe and wake vortices which are the main reasons for local scour. Either small cylindrical structures or separated vertical deflectors can be placed in front of the pier or the horizontal deflector (or collar) can be attached to the pier like the spoiler to reduce the dynamics of vortical structures. The second is to employ the protection layer to keep the bed material in place, which is a common method with a merit of immediate effect by using block mat or tetrapod. This study examined the effect of scour reduction using the former method. The relationship between the reflector interval and reduction of scour was not clear. It is assumed that the width of the reflector is somewhat correlated with the reduction of the scour. As the KC numbers increases, the Effect of Scour reduction rate is shown to decrease. Also, Scour reduction rate showed a rapid change at $U_R=25$ or KC = 8.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.2 no.4
• /
• pp.103-114
• /
• 1998

The floors of building structures equipped with vibrating machines can be susceptible to large vibration as a result of resonance or beating. Such a vibration can be reduced efficiently by using tuned mass dampers. However, the effectiveness of the damper depends greatly on the location and the natural frequency of the damper. To determine the optimum damper location is especially important since the dynamic behavior of a building structure varies with the location of the input loading. To this end, it is intended to decide the location and natural frequency of tuned mass dampers for reducing vibration of both loaded floors and floors located nearby the loaded floors considering the location and frequency components of the loading. The Vector composition method and the super elements are used th obtain the responses in steady states, and the optimum damper location and natural frequencies were found with the given damper mass.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.32 no.9
• /
• pp.788-795
• /
• 2008

To understand the tensile behaviors of GFRP at low temperature, three types of specimen have been used in this study. Tensile properties and fracture mechanisms for three orthogonal orientations of plain weave glass fabric reinforced epoxy resin laminate were investigated at temperature range of about -30 to $15^{\circ}C$. The tensile properties of axial and edge type specimen decrease slightly with decreasing temperature to $-20^{\circ}C$. However, at $-30^{\circ}C$ the decreases in the tensile properties increased considerably. Below $-20^{\circ}C$, thickness type specimen showed a marked decreases in the tensile properties. It was obvious that the fracture manner of thickness type specimen was adhesive failure at above $-10^{\circ}C$ and a mixed adhesive and cohesive failure at below $-20^{\circ}C$.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.17 no.3
• /
• pp.15-21
• /
• 2009

The anisotropic mechanical properties were measured for the three orthogonal orientations of plain weave glass fabric reinforced epoxy resin laminate. In tensile and flexural tests, axial and edge type specimens failed by pull-out of warp and fill yarns, respectively. In contrast, the thickness type specimens failed by adhesive failure process. Longitudinal cracking occurred in several of the edge type specimens during tensile test. That cracking caused pop-in in the stress-strain curve. Defects induced by improper coupon machining caused that cracking.

• Journal of the Korean Geotechnical Society
• /
• v.17 no.4
• /
• pp.221-229
• /
• 2001

연약지반의 측방유동으로 인한 피해가 예상되는 국내 현장에 성토지지말뚝공법을 적용하기 위한 연구의 일환으로 실제 현장에서 성토지지말뚝이 발휘하는 효과를 규명하기 위한 현장시험이 계획되었다. 본 현장시험은 직경 40.64cm의 강관말뚝을 3본씩 총 4여로 시공하고, 각 열의 줄말뚝은 콘크리트캡보로 연결한 다음 총 8m까지 성토하였다. 현장시험은 총 2회에 걸쳐 수행하였으며, 성토지지말뚝의 하중분담효과를 확인하기 위해 하중계, 토압계, 지중경사계, 그리고 침하판을 이용한 계측을 실시하였다. 또한 계측결과를 제안이론식과 비교분석하였다. 이러한 연구 결과 성토지지말뚝을 시공할 경우 성토지지말뚝 위 성토지반속에 발달하는 지반아치에 의해 대부분의 성토하중이 말뚝으로 전이됨을 확인하였고, 말뚝캡보의 설치 간격이 좁을수록, 그리고 성토고가 높을수록 성토지지말뚝의 하중분담효과가 더 커지게 됨을 확인할 수 있었다. 또한 설계시 성토지지말뚝의 설치범위를 합리적으로 결정하기 위해서는 성토지지말뚝이 성토사면의 사면안정효과에 미치는 영향을 고려해야 함을 알 수 있었으며, 제안이론식이 현장상태의 성토지지말뚝에 합리적으로 적용될 수 있음을 입증하였다.

• Solar Energy
• /
• v.18 no.3
• /
• pp.217-228
• /
• 1998

The purpose of this research is to investigate the characteristics of static and total pressure distribution in the upward free water jet system impinged on a downward flat plate. The rectangular nozzle was used and its contraction and aspect ratio was five and about seven respectively. Experimental conditions considered were jet velocity, distance between nozzle and flat plate, height of supplementary water. It was founded that pressure distribution on the flat plate had the Gaussian curve when the pressure at stagnation point and impinging half width were chosen as the scaling parameters. The maximum pressure was shown at the stagnation point. The central impingement velocity decreased with the increment of distance between nozzle and flat plate, and its slop of decay was similar to that of chracteristics decay region in the three-dimensional free jet.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.8 no.6 s.40
• /
• pp.55-66
• /
• 2004

Recently, many high-rise apartment buildings using the box system, composed of only reinforced concrete walls and slabs, have been constructed. In residential buildings such as apartments, vibrations occur from various sources and these vibrations transfer to neighboring residential units through walls and slabs. It is necessary to use a refined finite element model for an accurate vibration analysis of shear wall building structures. But it would take significant amount of computational time and memory if the entire building structure were subdivided into a finer mesh. Therefore, an efficient analytical method, which has only translational DOFs perpendicular to walls or slabs by the matrix condensation technique, is proposed in this study to obtain accurate results in significantly reduced computational time. If all of the DOFs except those perpendicular to walls or slabs in the shear wall structure eliminated using the matrix condensation technique at a time, the computational time for the matrix condensation would be significant. Thus, the modeling technique using super elements and substructuring technique is proposed to reduce the computational time for the matrix condensation. Dynamic analysis of 3-story and 5-story shear wall example structures were performed to verify the efficiency and accuracy of the proposed method. It was confirmed that the proposed method can provide the results with outstanding accuracy requiring significantly reduced computational time and memory.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.9 no.4
• /
• pp.109-118
• /
• 2005

A concrete shear wall system is commonly adopted in high-rise residential apartment buildings. In the construction stage, a rectangular opening is often made for the convenience of horizontal movement of workers, and construction materials and equipment. In the case of safety or stability assessment of a shear wall, the cutout part can be a critical factor. Finite element method is adopted to investigate the elastic stability behavior of the perforated unit shear wall. The key analysis parameters are the cutout location and its size. The effect of out-of-plane bending and horizontal shear are also examined in the stability analysis.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.22 no.3
• /
• pp.267-275
• /
• 2009

This paper presents the p-convergent coupling element on the basis of the ESSE(equivalent single layer shell element) and the PLLE(partial-linear layerwise element) to analyze laminated composite plates. The ESSE is formulated by the degenerated shell theory, on the other hand, the assumption of the PLLE is piecewise linear variation of the in-plane displacement and a constant value of lateral displacement across the thickness. The proposed finite element model is based on p-convergence approach. The integrals of Legendre polynomials and Gauss-Lobatto technique are chosen to interpolate displacement fields and to implement numerical quadrature, respectively. This study has been focused on the verification of p-convergent element. For this purpose, various finite element multiple models associated with the combination of ESSE and PLLE elements are tested to show numerical stability. The simple examples such as a cantilever beam subjected vertical load and a plate with tension are adopted to evaluate the performance of proposed element.