• Transactions of the Korean Society of Mechanical Engineers
• /
• v.10 no.1
• /
• pp.25-33
• /
• 1986

In this paper, the frontal method based elastic-plastic F.E.M. program for mini-computer was developed. Since, the executable source program size was restricted by the system core memory size on the mini-computer, the active variables were memorized by the element base and the nonactive varables were memorized to the external disc file. The active variables of the finally developed program were reduced enough to execute about 1,000 freedom finite element on the mini-computer on which available variables were restricted as 32,767 integers. A modified CT fracture test specimen was examined to test the developed program. The calculated results were compared with experimental results concerning on the crack tip plastic deformation zone. Recrystallization technique was adopted to visualize the intensive plastic deformation regions. The Von-Mises criterion based calculation results were well agreed with the experimental results in the intensive plastic region which was over than 2% offset strain. The F.E.M. results using the developed program were well agreed with the theoritical plastic boundary which was calculated by the stress intensity factor as r$_{p}$=(K$_{1}$$^{2}$/2.pi..sigma.$_{y}$$^{2}$).f(.theta.).).).

• The Journal of Engineering Geology
• /
• v.21 no.2
• /
• pp.147-156
• /
• 2011

We conducted laboratory experiments to determine the physical and mechanical properties, and the failure behaviors, of cements for use as grouting material in a $CO_2$-injection borehole. Samples with lour different ratios of water to cement mass (0.4, 1, 2, and 3) were tested. The analyzed properties (porosity, sonic velocity, modulus, and compressive and tensile strengths) varied systematically as a function of the ratio of water to cement (w/c), showing a sharp change between w/c ratios of 0.4 and 1. Triaxial compression tests revealed a clear boundary between brittle and ductile failure depending on the w/c ratio and confining pressure. The present results can be utilized as input parameters for numerical models to understand the initial deformation and failure behavior of grouting cements in a $CO_2$-injection borehole.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.6
• /
• pp.160-169
• /
• 2001

To predict busting failure in tubular hydroforming, the criteria for ductile fracture proposed by Oyane is combined with the finite element method. From the histories of stress and strain in each element obtained from finite element analysis, the fracture initiation site is predicted by mean of the criterion. The prediction by the ductile fracture criterion is applied to three hydroforming processes such as a tee extrusion, an automobile rear axle housing and lower am. For these products, the ductile fracture integral I is not only affected by the process parameters, but also by preforming processes. All the simulation results show the combination of the finite element analysis and the ductile fracture criteria is useful in the prediction of farming limit in hydroforming processes.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1995.05a
• /
• pp.611-616
• /
• 1995

핵연료 피복관의 일차 결함을 통해서 유입되는 냉각수에 의한 피복관 내면의 산화와 이에 따른 수소침투가 핵연료 피복관의 기계적 건전성에 미치는 영향을 규명하기 위한 연구를 수행하였다. 시험 시편은 Westinghouse, NRG, Sandvik에서 제조되는 Zircaloy-4 tube와 Westinghouse사에 개발한 신 합금인 ZIRLO™를 동일한 조건에서 수증기 산화와 수소 주입 실험을 수행하여 제조회사별 성능 평가를 하였으며 기계적 건전성 저하의 평가 방법으로 튜브 파열 실험(tube burst test)을 상온에서 수행하였다. 그 결과는 수소 침투량에 따라 피복관의 기계적 건전성이 지수적으로 감소하는 경향을 보였으며 500ppm이상에서는 취성파괴현상을 보이며 심각한 연성저하를 나타냈다. 제조회 사별 성능 평가에서는 A사 제품이 내식성과 수소흠수특성에서 다른 B, C, D사 제품에 비해 떨어지는 것으로 나타났다.

• Journal of the Microelectronics and Packaging Society
• /
• v.18 no.2
• /
• pp.63-67
• /
• 2011

We investigated effects of bonding conditions on the peel strength of rigid printed circuit board (RPCB)/ flexible printed circuit board (FPCB) joints bonded using a thermo-compression bond method, The electrodes on the FPCB were coated with Sn by a dipping process. We confirmed that the bonding temperature and bonding time strongly affected the bonding configuration and strength of the joints. Also, the peel strength is affected by dipping conditions; the optimum dipping condition was found to be temperature of $270^{\circ}C$ and time of 1s. The bonding strength linearly increased with increasing bonding temperature and time until $280^{\circ}C$ and 10s. The fracture energy calculated from the F-x (Forcedisplacement) curve during a peel test was the highest at bonding temperature of $280^{\circ}C$.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.18 no.1
• /
• pp.10-18
• /
• 2014

Mechanically fastening FRP (MF-FRP) strips using nails and anchors, has been shown to provide a more ductile behavior to the strengthened structural element than using bonded FRP. To further advance the state of the knowledge on this strengthening method, the current study examined environmental effects for six months on MF-FRP beams. Reinforced concrete beams strengthened with mechanically fastened FRP strips and subjected to sustained loads for six months were exposed to outdoor weather and constant high temperatures ($40^{\circ}C$). For comparison, the behavior of RC beam with and without sustained loads was evaluated. Results from flexural tests did not show any significant degradation or change of failure mode as a result of sustained load and of environmental effects such as high temperatures and outdoor weather over a period of six months. Failure of the beams was governed by FRP delamination followed by concrete crushing as not much load applied to the nail and anchors because of slip effects.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.32 no.4A
• /
• pp.227-235
• /
• 2012

Recently, study of confining effect in column members is progressed. But these studies are limited to about RC column and external confining effect in hollow columns. Internal confining effect in hollow columns has not researched. Internal confining stress is assumed the same external confining stress in hollow columns. In this study, there are to investigate the internal direction confining effect in ICH CFT column by FEA analysis. FEA analysis methods have verified by experimental values. Parametric study has performed as thickness of internal tube, hollow ratio, diameter of column and bending stiffness between concrete and external tube. Modified equations have suggested to estimating economic and reasonable thickness of internal tube.

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.77-77
• /
• 2009

ELV(; End of Life Vehicles)를 비롯한 최근 환경 동향은 자동차 전장 모듈에 대하여 다양한 무연 솔더 적용을 요구하고 있다. 특히 자동차 엔진룸과 트랜스미션은 가동 중 고온 및 진동의 지속적인 영향을 받기 때문에 이와 유사한 환경에서의 신뢰성 연구가 필요한 시점이다. 이에 본 연구에서는 Sn3.5Ag, Sn0.7Cu, Sn5.0Sb 솔더 조성에 대하여 복합환경 조건하에서 접합부 신뢰성을 평가하였다. 복합환경을 구현하기 위하여 $-40{\sim}150^{\circ}C$ 범위의 온도 사이클과 랜덤 진동을 동시에 인가하였으며, 진동 가속도 3G, 진동주파수는 10~1000Hz 로 설정하여 자동차 환경을 충족하였다. 복합시험의 1 cycle 은 20 시간이며, 총 120 시간의 시험 동안 진동의 영향 및 진동과 고온이 동시에 작용하였을 경우의 영향에 대해 비교하였다. 테스트 모듈 제작을 위해 450 um 의 솔더볼이 적용되었으며, 각 조성의 솔더볼을 이용하여 BGA test chip 제작하였고, 제작된 BGA test chip 은 다시 daisy chain PCB 위에 실장 및 리플로우 공정을 통해 접합되었다. 테스트 동안 In-situ 로 저항의 변화를 관찰하여 파단의 유무를 판단하였고 전자주사현미경을 통해 파괴 기전을 평가하였다. 복합시험 시간에 따른 전단강도를 측정하였으며, 각 조성에 대하여 상이한 전단강도 변화를 관찰하였다. 계면 IMC 형상은 전단강도 변화에 영향을 주었으며, 특히 높은 온도가 IMC 성장을 촉진시켜 전단강도 감소에 영향을 주었다. 본 복합환경 시험 조건에서는 Sn0.7Cu 가 가장 안정적이었으며, 파단면을 관찰한 결과 연성파괴 모드가 관찰되었다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.154-154
• /
• 2009

본 연구는 고전압 전력기기인 몰드형변압기와 계기용 변성기인 CT, PT 절연특성에 유용한 Epoxy/Nano-Micro Mixture Composites(이하,ENMMC)를 개발하기위해 무엇보다 중요한 것은 Nano입자인 $SiO_2$_10nm입자의 표면을 제어하여 즉, 표면의 소수성을 크게 하여 나노입자의 균질한 분산을 얻은것이 무엇보다 중요하다. 개발된 Epoxy/$SiO_2$_10nm Nanocomposites와 Microcomposites을 기계적 전단응력을 이용하여 균질 혼합을 실시하였다. 이런 조건을 이용한 전기적특성을 측정하기위해 구대구 전극이 완전함침된 평등전계하에서 절연파괴전압을 측정하기 시편을 제조하였다. 마이크로입자의 충진함량을 일정하게 유지하여 나노입자 충진함량비율을 4가지로 변화시켜 절연파괴특성을 연구하였다. 충진함량이 나노입자의 경우 1wt%이하의 값이 상대적으로 우수한 절연파괴특성으로 와이블 플롯을 통하여 알수있었다. 상대적으로 멀티나노콤포지트의 형상파라미터가 큰 결과값을 얻을수 있었다. 그리고 스케일파리미터는 누적확률 밀도함수로서 63.2%에서 대단히 큰 초절연성의 절연소재를 개발할수 있었다.

• Magazine of the Korea Concrete Institute
• /
• v.10 no.6
• /
• pp.345-352
• /
• 1998

Compressive strength of concrete compression members strengthend with carbon fiber laminate(CFL) were studied from the test results. Test parameters are spacing, thickness, width, ply and spliced length of carbon fiber laminates. Specimens strength with sheets failed with sudden tensile rupture of the laminate, which indicate very brittle failure mode. Test result shows that closer spacing and to increas thickness of CFL is more effective. But strengthening ratio with 1-ply CFL is more effective than that of specimen with 2-ply CFL. Compressive strength capacity of specimen splied 24cm shows almost similar strength to that of non-spliced specimen. The ultimate load carrying of specimen strengthened with CFL ranges 1.11~1.86 times of that of non-strengthened specimen.