• Proceedings of the Korean Society of Surveying, Geodesy, Photogrammetry, and Cartography Conference
• /
• 2000.10a
• /
• pp.40-50
• /
• 2000

본 연구에서는 Rolleiflex 6006 측정용 카메라로 촬영된 사진과 DCS 420 디지털 카메라로부터 촬영된 화상을 이용, 수치근접사진측량을 실시한 후, 조경석의 표면 거칠기 측정 정확도 향상을 위하여 최소제곱법으로 기준평면 또는 기준곡면을 찾아 사용하는 방법을 연구하였으며, 조경석 표면의 연마 이전과 연마 이후의 표면 거칠기를 측정, 비교하여 연마후의 거칠기 감소크기를 산출하고, 측정 정확도를 알아보기 위하여 거칠기가 거의 없는 평면인 돌과 곡면인 돌의 표면 거칠기를 측정한 결과, 그 거칠기를 기대정확도 이상인 각각 $\pm$0.lmm 및 $\pm$0.2mm의 정확도로 측정할 수 있었다. 또한 측정용 카메라인 경우 렌즈왜곡 보정에 있어서 검정자료를 토대로 기준점을 사용하지 않는 직접보정방법인 Newton-Raphson법을 적용하여 기하학적 정확도가 향상된 수치사진화상을 얻을 수 있었으며, DCS 420 디지털 카메라와 윈도우 운영체계인 Visual basic 6.0을 이용하여, 표면 거칠기 측정시스템을 구축함으로써 연마이전 조경석과 연마이후 조경석에 대한 표면 거칠기 및 형상을 정밀 측정할 수 있는 수치근접사진측량기법을 제시할 수 있었다.

• The Journal of Engineering Geology
• /
• v.8 no.3
• /
• pp.235-245
• /
• 1998

Adquate friction resistance is needed to prevent pavement slipperiness and to allow vehicles to stop in a reasonable distance. Performance of the aggregates is reduced over time by wear and polishing as a consequence of vehicular traffic. In this research, the objective was to develop a laboratory method to test Indiana gravel aggregates to predict field performance, and determine causes for the range of values amang gravel aggregates. The assessment of gravel sources was primarily on the basis of individual rock types and those proportions comprising the gravel. Polish and friction values were determined in the laboratory with the British Wheel and Pendulum. The gravels of this study were composed primarily of carbonate aggregates that showed considerable variability in polishing thresholds. Igneous and metamorphic constituents polished to a lesser degree and are expected to improve overall aggregate performance. Estimates of the IFV (Initial Friction Value) and PV (Polished Value) for crushed gravel samples can be made based on the percentage of rock types present in the sample. A weighted average is used to make this calculation.

• Korean Journal of Optics and Photonics
• /
• v.19 no.6
• /
• pp.422-428
• /
• 2008

The pitch tool provides superior surface roughness compared to other types of polishing tool. However, because of difficulty in handling the pitch tool, pitch tool polishing has rarely been analysed, which led many craftsman to eliminate the pitch tool from their experiences. We found that it was possible to use a pitch tool in the well-determined material removal after the completion of computer simulation and experiment. We could simulate the TIF of the pitch tool with 79% accuracy. Also, after five successive simulations of polishing process on a 280 mm optical flat, the surface p-v error was found to be reduced from $1{\mu}m$ to 168 nm.

• Journal of Astronomy and Space Sciences
• /
• v.21 no.2
• /
• pp.141-152
• /
• 2004

Optics fabrication process for precision space optical parts includes bound abrasive grinding, loose abrasive lapping and polishing. The traditional bound abrasive grinding with bronze bond cupped diamond wheel leaves the machine marks of about $20{mu}m$ rms in height and the subsurface damage of about 1 ${mu}m$ rms in height to be removed by subsequent loose abrasive lapping. We explored an efficient quantitative control of precision CNC grinding. The machining parameters such as grain size, work-piece rotation speed and feed rate were altered while grinding the work-piece surfaces of 20-100 mm in diameter. The input grinding variables and the resulting surface quality data were used to build grinding prediction models using empirical and multi-variable regression analysis. The effectiveness of such grinding prediction models was then examined by running a series of precision CNC grinding operation with a set of controlled input variables and predicted output surface quality indicators. The experiment achieved the predictability down to ${pm}20$ nm in height and the surface roughness down to 36 nm in height. This study contributed to improvement of the process efficiency reaching directly the polishing and figuring process without the need for the loose abrasive lapping stage.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1990.11a
• /
• pp.69-72
• /
• 1990

최근의 전자및 광학기기 분야에 있어서의 준부신 발전은 다면경 가공기나 초정밀 절삭, 연삭기와 같은 초정밀 가공기계의 개발과 실용화에 힘입은 바 크다. 이러한 초정밀 가공기의 성능을 좌우하는 핵심 요소로서 주축계를 들 수 있으며, 비교적 소형 경량의 공작물을 가공하는 기계의 주축용 베어링으로는 볼 베어링이나 오일 베어링을 대신하여 공기베어링이 점차 널리 사용되고 있다. 일반적으로 주축으로 사용되는 베어링은 원통형 레이디얼 베어링과 원판형 스러스트 베어링이 결합된 형식이 주류를 이루나 이러한 베어링은 스러스트 판과 축의 직가곧 가공오차가 존재하기 때문에 가공하기는 쉬우나 회전시에 의의 영향에 의해 회전 정밀도 유지가 어렵다는 단점을 지니고 있다. 이러한 단점을 보완하기 위하여 사용되는 베어링에는 원추형(conical) 베어링과 구면형(spherical) 베어링이 쓰이고 있다. 이러한 원추형 베어링과 구면형 베어링은 가공오차를 베어링과 축의 현압 연마로써 없애줄 수 있으며 베어링이 축방향 하중과 경방향 하중을 동시에 지지하여 줌으로써 기계 전체의 부피를 줄이고 회전 정밀도를 향상시켜 주는 것으로 알려져 있다. 그러나 구면의 베어링 간극을 정확히 가공하기 어려운 단점이 있어 축과 베어링을 현압연마하여 가공한 후에 두부품을 중심선상에서 분리시키므로써 요구되는 간극을 얻을 수 있는 원추형 베어링이 많이 쓰이고 있다. 본 연구에서는 직접 수치 해법을 이요하여 원추형 베어링의 유막내의 압력 분포를 계산하고 이 합력인 하중지지 용량이 축방향 하중과 경방향 하중을 지지하는 특성을 이론적으로 검토하여 외부 가압 원추형 베어링으 특성수를 파악하여 설계자료를 제시하고자 한다.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.24 no.4
• /
• pp.337-349
• /
• 2008

Despite an improved bone reactions of Mg-incorporated implants in the animals, little yet has been carried out by the experimental investigations in functional loading conditions. This study investigated the clinical and histologic parameters of osseointegrated Mg-incorporated implants in delayed loading conditions. A total of 36 solid screw implants (diameter 3.75 mm, length 10mm) were placed in the mandibles of 6 beagle dogs. Test groups included 18 Mg-incorporated implants. Turned titanium Implants served as control. Gold crowns were inserted 3 months. Radiographic assessments and stabilitytests were performed at the time of fixture installation, $2^{nd}$ stage surgery, 1 and 3 months after loading. Histological observations and morphometrical measurements were also performed. Of 36 implants, 32 displayed no discernible mobility, corresponding to successful clinical function. There was no statistically significant difference between test implants and controls in marginal bone levels (p=0.413) and RFA values. The mean BIC % in the Mg-implants was $54.4{\pm}20.2%$. The mean BIC % in the turned implant was $48.9{\pm}8.0%$. These differences between the Mg-implant and control implant were not statistically significant (P=0.264). In the limitation of this study, bone-to-implant contact (BIC) and bone area of Mg-incorporated oxidized implant were similar to machine-turned implant. The stability analysis showed no significantly different ISQ values and marginal bone loss between two groups. Considering time-dependent bone responses of Mg-implant, it seems that Mg-implants enhanced bone responses in early loading conditions and osseointegrated similarly to cp Ti implants in delayed loading conditions. However, further investigations are necessary to obtain long-term bone response of the Mg-implant in human.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.42 no.3
• /
• pp.218-225
• /
• 2015

This study used sodium fluorescein to improve imaging diagnostic ability by increasing the fluorescence difference between sound enamel and caries lesions. It also made it easier to discriminate between stain and caries lesions using quantitative light-induced fluorescence (QLF). Half of the specimen surface was covered with nail varnish as a control. Specimens were divided randomly in six decalcification groups and decalcified for different lengths of time. Then, ${\Delta}F$ was measured using QLF-D. After applying 0.075% sodium fluorescein, we measured ${\Delta}F$ again and compared it with the initial value. After cutting the central portion of the specimen, we measured the lesion depth using scanning electron microscopy. The lesion surfaces observed with QLF were darker than normal enamel, whereas they were lighter than normal enamel after applying fluorescein. Longer decalcification time was associated with greater fluorescent dye penetration. The ${\Delta}F$ measured after applying fluorescein was higher than the initial value (p < 0.05). Due to QLF measurement using fluorescein being more sensitive for diagnosing early decalcification, this approach will enable early diagnosis of dental caries before the cavity formation stage, allowing the treatment of early caries lesions. With QLF and sodium fluorescein, we can easily discriminate between stain and caries lesions.

• The Journal of Korean Academy of Prosthodontics
• /
• v.46 no.5
• /
• pp.511-519
• /
• 2008

Statement of problem: An incompatibility between the initiator systems of self-curing composite resins and light-curing adhesives was supposed recently. Purpose: The purpose of the study was to evaluate the influence of activators for self/dual bonding on dentin shear bonding strengths. Material and methods: Fifty human molars were divided into 5 groups. A flat dentin surface was created for each tooth. A self-curing composite resin (Luxacore) was bonded with the following adhesives (n = 10); One-Step, Prime&Bond NT, AdheSE, Prime&Bond NT and AdheSE were also used in combination with activators. Shear bond strengths were measured after 24 hours of water storage. The specimens were loaded in shear in the Instron until failure at a 1 mm/min crosshead speed. Data were compared using one-way ANOVA and Tukey HSD test (${\alpha}$= 0.05). Results: The dentin adhesive systems in order of decreasing median bond strength were One-Step > Prime&Bond NT with activator, AdheSE with activator > Prime&Bond NT, AdheSE. Among adhesives, One-Step had the highest bond strength. Prime&Bond NT with activator had higher bond strengths than Prime&Bond NT that was used alone, and so was AdheSE. Conclusion: Shear bond strengths were increased in Prime&Bond NT and AdheSE when these were used with activators comparing used without activators. But using activators was not effective clinically comparing One-Step.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.26 no.3
• /
• pp.538-553
• /
• 1999

The purpose of this study was to compare the shear bond strength and the anticariogenicity of glass ionomer cement with conventional bonding resin and fluoride releasing resin. After the shear bond strength test, scanning electron microscopic observation was performed for the evaluation of the fracture patterns in each group. Under the polarizing light microscope, artificially induced carious lesions were evaluated and the lesion depths of the samples were measured using image analyzing program(Image-Pro $PLUS^{TM}$, USA). 50 sound maxillary premolars were used for the bond strength test and another 30 for the anticariogenic test. Data collected were analyzed statistically using Oneway-ANOVA and Scheffe test. The results were as follows: 1. Glass ionomer groups(G-III, IV, V) generally showed the lower bond strength values than resin groups(G-I, II). 2. Among the two resin groups, G-I showed the higher bond strength than G-II without statistically significant difference between them(p>.05). 3. Within glass ionomer groups, statistical significance was found between G-III and G-V with the superior bond strength in G-V (p<.05). 4. Under the SEM, adhesive failure was the predominant fracture pattern in G-I and II, whereas cohesive failures were mainly observed in G-III. In G-IV and V, mixed type of pattern where the both fracture patterns coexisted within samples could be seen. 5. In evaluation of the depth of artificially developed carious lesion, glass ionomer group showed shallower depth than resin groups with statistical significance between G-III and G-I, II(p<.05). Among resin groups, fluoride releasing resin(G-II) showed the shallower depth than conventional resin(G-I)(p<.05).