• Journal of Korean Tunnelling and Underground Space Association
• /
• v.24 no.2
• /
• pp.153-170
• /
• 2022

Waterjet has been comprehensively used in urban areas owing to a suitable technique for cutting concrete and rock, and low noise and vibration. Recently, the abrasive waterjet technique has been adopted and applied by the Korea Atomic Energy Research Institute to demolish concrete plugging without disturbing and damaging In-situ Demonstration of Engineered Barrier System in the disposal research tunnel. In this study, the use of abrasive waterjet in the tunnel was evaluated for practical applicability and the existing cutting model was compared with the experimental results. As a variable for waterjet cutting, multi-cutting, water flow rate, abrasive flow rate, and standoff distance were selected for the diversity of analysis. As regarding the practical application, the waterjet facilitated path selection for cutting the concrete plugging and prevented additional disturbances in the periphery. The pump's noise at idling was 64.9 dB which is satisfied with the noise regulatory standard, but it exceeded the standard at ejection to air and target concrete because the experiment was performed in the tunnel space. The experimental result showed that the error between the predicted and measured cutting volume was 12~13% for the first cut and 16% for second cut. The standoff distance had a significant influence on the cutting depth and width, and the error tended to decrease with decrement of standoff distance.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.14 no.4
• /
• pp.421-435
• /
• 2012

Rock excavation (removal) tests are performed with effective parameters using an abrasive waterjet. For verification of the field rock excavation capabilities, the removal performance and level of efficiency are analyzed for hard granite rock in terms of the water pressure, exposure time of the jet, and the standoff distance. In particular, experimental tests are performed with a long standoff distance required condition in the real excavation field. The rock removal performance level changes according to the rock properties. In this study, various rock specimens are used and P-wave velocities are measured in order to determine the correlation between the removal performance and the P-wave velocity. As a result of the experimental study, the effect of waterjet parameters on rock removal is analyzed.

• Journal of IKEEE
• /
• v.23 no.4
• /
• pp.1387-1392
• /
• 2019

Aspherical mirrors have lighter weight and better performance than spherical mirrors, but it is difficult to process their shape and measure the processing precision. Especially, large aperture aspherical mirrors mounted on satellites need high processing precision and long processing time. The computerized numerically controlled machine of gantry type has been used in polishing process, but it has difficulties in processing the complex shapes due to the lack of degrees of freedom. In order to overcome this problem we developed a polishing system using an articulated industrial robot. The system consists of tool path generating program, real-time robot monitoring, and control program. We show the performance of the developed system through the computer simulation and actual robot operation.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.15 no.1
• /
• pp.32-38
• /
• 2006

The magnetic fluid polishing technique can polish the tool of complex shape, because the polishing method which polishes as compress the workpiece by the magnetism abrasives to arrange to the linear according to the line of magnetic force. Therefore, we producted the magnetic fluid polishing device in order that mirror like finishing processes the tool surface. In order to a polishing condition selection, polishing characteristic was estimated by polishing conditions which are magnetic flux density, polishing speed, grain size, magnetic fluid. The tool was polished to the selected polishing condition. The result to evaluate the polished tool's performance with the cutting force and tool wear, the polished tool's performance was improved compared with the tool not to polish.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.12
• /
• pp.37-43
• /
• 2004

The performance of magnetic abrasive finishing fur surface is evaluated by the characteristic curve. The characteristic curve is generated by experiment in surface finishing. For experiment, new magnetic inductor is designed and manufactured. 15 kinds of powders are provided to find the relationship between powder characteristic and finishing performance. As powder, Fe-TiC. Polymer-TiC and Fe-NbC are used with different size. The size of abrasives and location are also important factor for the performance. From characteristic curve, two index are obtained, which specify the initial finishing performance and endurance of finishing performance. It is proved that the performance index can be applied to select proper powder for efficient deburring. It is shown that the characteristic curve can be used as good tools for evaluating powder performance in surface finishing and deburring.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2013.10a
• /
• pp.383-385
• /
• 2013

반도체소자의 고속실현을 위해서 알루미늄배선에서 40% 가량 성능을 높이는 반면 제조비용은 30%까지 낮출 수 있는 구리를 선호하고 있으나, 식각이 잘 되지 않아 원하는 패턴으로 만들어 내기가 곤란한 공정기술의 어려움과 구리물질이 지닌 유독성문제를 가지고 있다. 기존의 식각기술로는 구리패턴을 얻을 수 없는 기술적 한계 때문에 화학.기계적 연마(CMP)를 이용한 평탄화와 연마를 통해서 구리배선을 얻는 다마스커스(Damascene)기술이 개발됐고 이를 이용한 구리배선기술이 현실적으로 가능하게 됐다. CMP를 이용한 평탄화 및 연마 공정에서 Wafer에 도포된 구리의 두께를 실시간으로 측정하여 정밀하게 제어할필요가 있는데, 본 논문에서는 와전류를 이용하여 옹고스트롬 단위의 두께를 실시간으로 측정하여 제어 하는 시스템구현에 대해 기술한다.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.24 no.6
• /
• pp.42-49
• /
• 2020

This paper is a basic study to improve durability by imparting hydrophobicity to the surface and sphere of cement-based materials. A cement mortar to which a silane/siloxane-based mixed water repellent was added was prepared, and its initial hydration performance, flow performance, and compressive strength were measured. In addition, after the surface was abraded, the water contact angle and water absorption were measured. The flow of cement mortar to which the water repellent was added was found to decrease up to 1.5% in the addition amount of the water repellent agent, and increased at 3.0% in the addition amount. It was found that the setting time of the cement paste was delayed in both the initial setting and the termination when the water repellent was added. It was found that the compressive strength decreased from 3.0% of the maximum added amount of the water repellent to a maximum of 30%. The contact angle was found to increase when the water repellent was added to the cement mortar, and the contact angle after surface polishing was found to be larger than before surface polishing. The addition of the water repellent showed hydrophobicity not only on the surface but also on the surface and cross section damaged by polishing. The water absorption rate was found to decrease when the water repellent was added to the cement mortar, and the water absorption rate after surface polishing was found to be greater than before surface polishing.

• ETRI Journal
• /
• v.14 no.1
• /
• pp.108-117
• /
• 1992

광통신 시스팀에서 신호접속용으로 사용되는 광커넥터의 결합기구 중 세라믹 페룰-슬리브의 정렬기구에서 발생하는 성능저하 현상을 다루었다. 성능저하 현상으로 페룰 단면연마시 발생하는 Vertex Eccentricty, 좌굴현상, 환경에 따른 탄성 및 응력의 변화, 마모, 피로파괴 등에 대한 이론적인 배경과 실험결과를 토대로 특성에 대한 영향을 분석하였다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.10a
• /
• pp.354-361
• /
• 2005

In high speed cutting process, due to the friction between the tool and workpiece, a temperature rise of contacting part is serious. It need to develop cutting tool for overcoming such a poor condition. So now, some studies, the optimization of tool shapes, the fine grains of tool material, multi-layer coating of tools are processing. If mirror finishing on the tool is processed, there is advantage of relation between chip and tool, because of less friction, and also tool's lift would be increased. As a result mirror like finishing is expected efficient enhancement of tool. Generally, it is too difficult to process by a general way for tools of complex shapes, it is required a new method to process such complex shape tools. The magnetic fluid polishing technique can polish the workpiece of complex shape, because the polishing method which polishes as compress the workpiece by the magnetism abrasives to arrange to the linear according to the line of magnetic force. In this paper, We polished the surface of the high speed cutting tool using the magnetic fluid polishing technique, to enhance the performance of the high speed cutting tool.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2006.06a
• /
• pp.37-38
• /
• 2006