• Journal of the KSME
• /
• v.31 no.1
• /
• pp.43-50
• /
• 1991

로봇의 설계시 고려하여야 하는 여러가지 면을 기술하였다. 평면 3자유도 링크의 경우 길이비를 "Fibonacci Sequence"를 따라가도록 결정하였으며 여유자유도를 갖는 직접구동로봇의 설계 및 제작시 유의하여야 할 사항을 정리하였다. 몸체설계후 POSTECH DD 로봇을 위한 실시간 제 어환경이 구성되었으며 VME버스의 MC68020/68882 프로세서를 탑재한 "one board" 컴퓨터에서 모든 로봇제어 소프트웨어가 수행되었다.든 로봇제어 소프트웨어가 수행되었다.

• Proceedings of the KIEE Conference
• /
• 2000.11d
• /
• pp.758-760
• /
• 2000

본 논문에서는 기구적으로 여유자유도를 갖는 로봇 매니퓰레이터 시스템을 대상으로 하여, 로봇 랜드가 주어진 제적을 추종할 수 있는 관절 토크를 유도하기 위한 동적제어 식을 새로이 구성하고, 동적제어식을 만족하는 관절 토크 해들 중에 국소적으로 토크의 크기를 최적화하는 해를 사용하는 최적토크제어를 제안한다. 최적토크를 구하는 문제에 있어 관절 토크에 가중치 행렬을 적용하여 각 관절 토크의 최대 크기의 비를 반영할 수 있도록 한다. 또한, 로봇 핸드 자코비안-관성 역행렬의 영공간에서 나타나는 영공간 관절 속도를 정의하고 이러한 영공간 관절속도가 최적토크제어에서는 로봇 시스템을 불안정하게 할 수 있다는 것을 보인다. 최적토크 제어의 이러한 문제를 해결하기 위하여 영공간 관절 속도를 제거하기 위한 소산토크를 유도하고, 최적토크제어식에 소산토크를 추가하는 방법을 제안한다. 평면형 3-자유도 로봇을 대상으로 한 모의실험을 통해 제안된 제어 방법의 우수성을 검증하고 그 결과를 분석한다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2012.05a
• /
• pp.279-280
• /
• 2012

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.12
• /
• pp.66-72
• /
• 2001

In this paper, by using pseudo-inverse matrix of the spatial redundant flexible manipulators, a position control method and its effect in vibration suppression was presented. Vibration suppression control was developed using lumped mass spring model of the flexible manipulators. With 2 elastic links and 7 rotory joint manipulator ADAM, (1)position control for no redundancy, and (2)position control for one redundant DOF(degree of freedom) were tested. The objective of this experiment is to show the effect of position control, using pseudo-inverse matrix. toward the improvement of operation, and at the same time, to reduce the vibration of the link and the magnitude of the joint torque.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.33 no.10
• /
• pp.1014-1022
• /
• 2009

A biped robot in locomotion can be regarded to be kinetically redundant in that the link-chain from its foot on the ground to its swing foot has more degrees of freedom that needed to realize stable bipedal locomotion. This paper proposes a new method to generate a trajectory for bipedal locomotion based on this redundancy, which directly generates a locomotion trajectory at the joint level unlike some other methods such as LIPM (linear inverted-pendulum mode) and GCIPM (gravity-compensated inverted-pendulum mode), each of which generates a trajectory of the center of gravity or the hip link under the assumption of the dominance of the hip-link inertia before generating the trajectory of the whole links at the joint level. For the stability of the trajectory generated in the proposed method, a stability condition based on the ZMP (zero-moment point) is used as a constraint as well as other kinetic constraints for bipedal motions. A 6-DOF biped robot is used to show how a stable locomotion trajectory can be generated in the sagittal plane by the proposed method and to demonstrate the feasibility of the proposed method.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.4
• /
• pp.187-194
• /
• 2002

In this paper, a motion control algorithm is developed using a fuzzy control and the optimization of performance function, which makes a robot arm avoid an unexpected obstacle when the end-effector of the robot arm is moving to the goal position. During talc motion, if there exists no obstacle, the end-effector of the robot arm moves along the predefined path. But if these exists an obstacle and close to talc robot arm, the fuzzy motion controller is activated to adjust the path of the end-effector of the robot arm. Then, the robot arm takes the optimal posture far collision avoidance with the obstacle. To show the feasibility of the developed algorithm, numerical simulations are carried out with changing both the positions and sites of obstacles. It was concluded that the proposed algorithm gives a good performance for obstacle avoidance.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.20 no.12
• /
• pp.3871-3882
• /
• 1996

In this paper, a closed-form formulation for inverse kinematics of robot manipulators with kinematic redundancy under the constrained environment has been derived using the Kuhn-Tucker condition, the extended Lagrange multiplier method and the working set method. The proposed algorithm satisfies the necessaryand sufficient conditions for optimization subject to equality and inequality constraints. In addition, computationally efficient kinematic control methods have been proposed using differential kinemetics and gradient projection mehtod. The effectiveness of the proposed methods has been demonstrated with a 4-dof planar robot, and then a 7-dof spatial robot as a practical application to the nozzle dam task in the Nuclear Power Plant.

• Journal of the Korean Society for Precision Engineering
• /
• v.10 no.4
• /
• pp.227-235
• /
• 1993

In this paper, the development of a high performance flexible controller is described. The hardware of the controller, based on VME-bus, consists of four M68020 single-board computers (32-bit) with M68881 numerical coprocessors, two M68040 single board donputers, I/O devices (such as A/D and D/A converters, paraller I/O, encoder counters), and bus-to-bus adaptor. This software, written in C and based on X-window environment with Unix operating system, includes : text editor, compiler, downloader, and plotter running in a host computer for developing control program ; device drivers, scheduler, and mathemetical routines for the real time control purpose ; message passing, file server, source level debugger virtural terminal, etc. The hardware and software are structured so that the controller might have both flexibility and extensibility. In papallel to the controller, a three degrees of freedom kinematically redundant robot has been developed at the same time. The development of the same time. The development of the robot was undertaken in order to provide, on the one hand, a computationally intensive plant to which to apply the controller, and on the other hand a research tool in the field of kinematically redundant manipulator, which is, as such, an important area. By using the controller, dynamic control of the redundant manipulator was successfully experimented, showing the effectiveness and flexibility of the controller.

• The Magazine of the IEIE
• /
• v.23 no.12
• /
• pp.102-114
• /
• 1996

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.41 no.4
• /
• pp.422-432
• /
• 1992

Previous investigations of redundant manipulators have often focussed on local optimization for redundancy resolution by using the Jacobian pseudoinverse to solve the instantaneous relationship between the joint and end-effector velocities. This paper establishes some new goals for redundancy resolution at position level by using configuration control approach which has been recently developed. Minimum gravity loading, joint limit avoidance, minimum sensitivity, maximum stiffness and minimum impulse are introduced as redundancy resolution goals. These new goals for redundancy resolution allow more efficient utilizations of the redundant joints based on the desired task requirements. Simple computer simulation examples are given for illustration.