• Journal of the Microelectronics and Packaging Society
• /
• v.15 no.1
• /
• pp.27-31
• /
• 2008

Due to the increasing need for miniaturization of electronic device, embedded resistor technology using thick film resistance paste to embed resistors currently mounted on the board thus effectively reducing board size, is being extensively researched. In this research, thick film resistor paste having $0.35{\sim}4k{\Omega}/sq$ range of resistivity were fabricated using mixtures of carbon black and epoxy resin. In order to adjust the TCR (temperature coefficient resistivity), TCR modifiers such as Ni-Cr alloy, $SiO_2$ powder were added and were able to improve on TCR value with $100ppm/^{\circ}C$. Finally embedded resistor board using thick film resistance paste were fabricated. Stable resistivity value and reliability results were achieved.

• Applied Chemistry for Engineering
• /
• v.5 no.3
• /
• pp.517-523
• /
• 1994

The effects of cure kinetics and mechanism of DGEBA(diglycidyl ether of bisphenol A)/MDA(4,4'-methylene dianiline) with SN(succinonitrile) and HQ(hydroquinone) as an additive and accelerator were investigated. Cure kinetics was evaluated by Kissinger equation and fractional-life method through DSC analysis. The activation energy has hydroxyl group as an accelerator, the activation energy and the starting cure-temperature were lower than those of DGEBA/MDA/SN system. Cure mechanism of those systems was investigated through FT-IR according to the various SN contents. The ratio was SN : HQ = 4 : 1. It has been known that the cure reactions of an epoxy-diamine system are composed of primary amine-epoxy reaction, secondary amino-epoxy reaction and epoxy-hydroxyl group reaction. But in DGEBA/MDA/SN system, primary amino-CN group reaction and CN group-hydroxyl group reaction were added to the above mentioned reactions. These reactions attributed to the long main chain and the low crossliking density. And in DGEBA/MDA/SN/HQ system, hydroxyl group of HQ formed a transition state with epoxide group and amime group and also opened the ring of the epoxide group rapidly, then amino-epoxy reaction took place easily.

• Proceedings of the KWS Conference
• /
• 2010.05a
• /
• pp.78-78
• /
• 2010

모바일 정보통신기기를 중심으로 패키지의 초소형화, 고집적화를 위해 플립칩 공법의 적용이 증가되고 있고 있으며 접속피치의 미세화에 따라 솔더 및 언더필을 사용하는 C4 공법보다 ACA(Anisotropic Conductive Adhesive), NCA (Non-conductive Adhesive) 등의 접착제를 이용하는 칩본딩 공법에 대한 요구가 증가하고 있다. 특히, NCA 공법의 경우 산업 현장의 대량생산에 대응하기 위해서는 접착제의 속경화 특성이 요구되어 진다. 일반적으로 접착제의 경화거동은 DSC(Differential Scanning Calorimeter)를 사용해 확인하지만, 수초 이내에 경화되는 접착제의 경우는 적용되기 어렵다. 본 연구에서는 이러한 전자패키지용 접착제의 속경화 거동을 효과적으로 평가할 수 있는 방법을 조사 하였다. 실험에서 사용된 접착제는 에폭시계 레진 기반에 이미다졸계 경화제를 사용한 기본적인 포뮬레이션을 사용하였고, 경화시간은 160^{\circ}C에서 1분 이내에 경화되는 특성을 가지고 있다. 경화 거동을 확인하기 위해서 isothermal DSC와 DEA(Dielectric Analysis)의 두가지 방법을 사용해 비교하였다. 두 실험 방법 모두 $160^{\circ}C$를 유지하며 경화 거동을 확인하였고, DoC(Degree of Cure)의 측정오차를 비교 분석하였다. DEA는 이온 모빌리티 변화에 따른 유전손실율을 측정하는 방법으로 80~90% 이후의 경화도는 측정되지 않았지만, 수초 이내에 경화되는 속경화 특성을 평가하기에 적합한 것으로 확인되었다.

• 월간산업보건
• /
• s.105
• /
• pp.16-25
• /
• 1997

직업성 피부질환은 1988년 미국 전체 직업성 질환중 20%에 해당된다(미 노동부 자료 참고). 그 비율은 주에 따라 크게 달라지기도 한다. 피부질환은 어떤 주에서는 보상되는 직업성 질환의 대다수를 차지하기도 한다; 예를 들어, 캘리포니아와 플로리다주에서는 농작물에 의한 접촉성 피부염이 흔하다. 접촉성 피부염은 직업성 피부질환으로 보고되는 가장 흔한 피부질환이다. 이러한 사례의 4/5는 유기용제, 절삭유, 세척유, 알칼리, 산 등과 같은 자극성 화학물질에 대한 노출과 관련이 있다. 자외선은 어떤 화학물질(예를 들면, 코울 타르, 크레오소오트)과 반응하여, 이 화학물질 및 빛에 노출되는 부위에 자극성 접촉성 피부질환을 유발하기도 한다. 1/5의 사례는 에폭시 수지, 크롬, 식물 수지, 그 밖의 많은 것 등 특수 접촉 감광제와 관련될 수 있다. 강한 자극제에 노출되어 발상하는 화학적 화상은 비교적 흔하게 일어난다. 백반과 유사한 피부탈색은 드물게 일어나며 피부 접촉을 통하여 야기하는 특수 화학물질과 관련될 수 있다. 여드름과 모낭염은 기름 및 유지들과의 피부 접촉을 통하여 생겨날 수 있다. 10대 여드름과 구별되는 염소성 여드름이라고 불리는 질환은 여러 종류의 염화 탄화수소들(예를들면 다브롬화 디페닐, 다염화 디페닐, 디옥신)에 노출되어 발생되기도 한다. 신체적인 손상으로 반복되는 외상부위에 가골이 형성되기도 한다. 여러 종류의 일에 특징적인 것(예를 들면 바이올린 연주자의 목에 가골)이 소위 "직업적인 표지" 이다. 전기톱 작동 기술자, 분쇄기 작동기술자, 지하 광산 암석 천공 기술자에게서 발생하는, 손 - 팔 부위의 진동은 오랜기간 혹은 심하게 노출된 노동자에 있어서 - 손에 혈관수축질환 - 진동장애 백색 수지질환을 일으킬 수 있다. 피부암은 직업과 관련이 있다고 할 수 있다. 하지만 몇몇 사례가 산재 관련 기관에 보고외어 있지만, 암등록소에 보고는 불완전하며, 피부암으로 인한 사망은 드물기 때문에 피부암의 발생률은 알 수 없다. 예방적인 방법은 개인보호구(장갑, 구두 등), 기계공학적 통제, 노동자 교육, 피부에 노출되는 것을 피하기 위해 주어진 일을 맡는 노동자들의 교대와 같은 관리적인 통제가 있다. 이러한 방법들은 화학적 화상, 알러지성 접촉성 피부염과 같은 피부염, 진동장애, 직업관련성 질환(예를 들면, 건선, 단순태선, 백반)을 예방하는데 도움이 된다. 만성 자극성 접촉성 피부염은 아직 잘 이해하고 있지 못하여 현재 예방하는 방법은 아직 만족스럽지 못하다.

• Composites Research
• /
• v.14 no.2
• /
• pp.1-7
• /
• 2001

The studies on the formulation and curing behaviors of Kevlar/Epoxy prepreg for NOSE CONE of aircraft were presented in this paper. Dielectrometer and differential scanning calorimeter were used in order to check the curing behaviors. This prepreg showed the lowest ionic viscosity around $120^{\circ}C$, and then the ionic viscosity was gradually increased up to $200^{\circ}C$. This indicated that the curing reaction of this prepreg started at $120^{\circ}C$ and the molecular weight was increased by the accelerated thermal cross-linking reaction. The loss factor and tan $\delta$ values were also measured and discussed. The loss factor behaviors of Kevlar/Epoxy prepreg, which is related to the fluidity of matrix, were fecund to be similar with that of ionic viscosity. The thermal reaction properties of this prepreg were also studied by differential scanning calorimeter.

• Applied Chemistry for Engineering
• /
• v.10 no.6
• /
• pp.949-953
• /
• 1999

Because epoxy molding compound(EMC) for semi-conductor encapsulants contains high concentrations of fillers, its flow behaviors are affected much by the concentrations and properties of those fillers. This paper reports the effects of a filler concentration, shape, size, and size distributions on the viscosity behavior of EMC(epoxy/silica). In addition, the prediction of viscosity behavior was performed using the Mooney equation. The maximum packing volume in the Mooney equation was calculated by Ouchiyama's packing model and Taguchi's optimization method, while the shpae factor was determined by fitting the experimental data. The results showed that the Mooney equation predicted the viscosity behavior of EMC very well.

• Applied Chemistry for Engineering
• /
• v.24 no.1
• /
• pp.104-111
• /
• 2013

Poymer blends of two degradable aliphatic polyesters, relatively expensive material polylactic acid (PLA) and relatively inexpensive material poly(butylene adipate-co-terephthalate) (PBAT), were used in this study. Three different kinds of modifiers were used with various amounts. Diisocyanate type methylenediphenyl 4,4'-diisocyanate (MDI) and hexamethylene diisocyanate (HDI) were used as modifiers and epoxy type coupling agents also used. The melt flow index (MFI) and dynamic viscoelasticity of various compositions of PLA/PBAT blends were studied. The mechanical property and morphology with respect to the fracture surface of PLA/PBAT blends were also investigated using tensile test and field emission scanning electronic microscopy, respectively. These tests were also used to verify the compatibility of PLA/PBAT and the effect of mechanical properties due to the use of modifiers. Tensile properties of PLA/PBAT blends modified with HDI were improved remarkably.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.42 no.4
• /
• pp.336-343
• /
• 2014

Modern advanced-turboprop propellers are required to have high structural strength to cope with the thrust requirement at high speed. The high stiffness and strength carbon/epoxy composite material is used for the major structure and skin-spar-foam sandwich structural type is adopted for advantage in terms of the blade weight. As a design procedure for the present study, the structural design load is estimated through investigation on aerodynamic load and then flanges of spars from major bending loads and the skin from shear loads are sized using the netting rule and Rule of Mixture. In order to investigate the structural safety and stability, stress analysis is performed by finite element analysis code MSC. NASTRAN. It is found that current methodology of composite structure design is a valid method through the static structural test of prototype blade.

• Applied Chemistry for Engineering
• /
• v.27 no.5
• /
• pp.490-494
• /
• 2016

This paper describes the very efficient and highly enantioselective ring opening of terminal epoxides with alkyl and arene sulfonic acid. The dinuclear chiral (salen) Co complexes bearing Lewis acids of Al, Ga and In catalyze the reaction enantioselectively in the presence of tetrabutylammonium chloride using tert-butyl methyl ether as a solvent. The variation of the anion of the tetra butyl ammonium salt has significant impact on the reactivity and selectivity of the asymmetric ring opening of phenyl glycidyl ether with p-toluenesulfonic acid. The order of reactivity and selectivity was found to be $Cl^-$ > $l^-$ > $Br^-$ > $OH^-$. Strong synergistic effects of the different Lewis acid centers of Co-Al, Co-Ga and Co-In complexes were observed in the catalytic process. The dinuclear chiral salen catalyst containing $AlCl_3$ was found to be most active and highly enantioselective (91% ee).

• Composites Research
• /
• v.26 no.3
• /
• pp.189-194
• /
• 2013

This paper deals with the study of mechanical properties and impact energy absorbed by composites, made by using thermoplastic and thermoset as matrix, flax fiber and nanoclay as reinforcements. The nanoclay was sprayed on the fiber laminate directly after mixing with ethanol. This experiment designed by Taguchi method and have variable factors, i.e three types of fiber direction(F), three different nanoclay wt%(N) and three spray gun hole shapes(S). According to these conditions, composites were made and the optimum conditions were found to be F1N3S1, F1N2S1, F1N2S1 and F3N2S1 for thermoplastic, and F1N3S2, F1N3S2, F1N2S2 and F3N2S1 for thermoset which were matched with tensile strength, modulus, total impact absorbed energy and heat release rate respectively.