• Journal of Advanced Marine Engineering and Technology
• /
• v.40 no.4
• /
• pp.282-287
• /
• 2016

Recently in order to protect the ocean environment and to reduce energy consumption, shipbuilders have been developing highly economized ships. This research analyzed the possibility of adopting the onshore absorption refrigerator to offshore ships having a cooling system with refrigerant by using the waiste heat of the engine jacket cooling water instead of compression refrigerators. The results showed that R236fa could be a suitable medium for absorbing the heat of the absorber and condenser in an absorption refrigerator. The cooling system using R236fa achieved a high COP of 0.798, which is 15% and 5% higher than an air cooling system with a cooling tower and a water cooling system with a heat exchanger, respectively. The cooling system with R236fa achieved high efficiency with a 25% reduction in flow rate of LiBr solution and only 15.7% flow rate of cooling medium as compared to the water cooling system. The heating of sea water by the engine jacket water flowing out from the generator can prevent the crystallization of LiBr solution due to the low temperature of sea water.

• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.7
• /
• pp.722-728
• /
• 2015

The demand for shipboard energy management is expected to gradually increase based on ship energy efficiency management plans (SEEMPs), which have been in use since January 1, 2013. Therefore, the fuel consumption of the main engine, which occupies the greatest portion of the energy used, along with elements related to the engine power, should be strictly monitored. There are many different methods for indicating the engine power. However, this study performed an experiment to monitor the status of a ship's engine power in real time using an encoder and a proximate switch, which are economical to purchase and easy to install. In the experiment, the angular velocity during one cycle of a two-stroke low-speed engine was measured, and the measured data were converted to the torque fluctuation. The angular velocity during an abnormal firing condition in the cylinder was also measured, and the torque fluctuation as a result of a misfire was considered. The results were compared with sea trial data to determine the reliability. In this study, the status of the engine power was determined using the torque fluctuation of the main engine in an operating ship.

• Journal of the Society of Naval Architects of Korea
• /
• v.54 no.3
• /
• pp.171-186
• /
• 2017

This paper introduces a study on ship performance in waves to consider the effects of added resistance in the early stage of hull-form design. A ship experiences a loss of speed in actual seaways, hence this study proposes the overall procedure of a new design concept that takes into account the hydrodynamic performance of ship in waves. In the procedure, the added resistance is predicted using numerical methods: slender-body theory and Maruo's far-field formulation, since these methods are efficient in initial design stage, and an empirical formula is adopted for short waves. As computational models, KVLCC2 hull and Supramax bulk carrier are considered, and the results of added resistance and weather factor for test models are discussed. The computational results of vertical motion response and added resistance of KVLCC2 hull are compared with the experimental data. In addition, the sensitivity analysis of added resistance and weather factor for KVLCC2 hull to the variations of ship dimensions are conducted, and the change of the added resistance and propulsion factors after hull form variations are discussed.

• Journal of Advanced Navigation Technology
• /
• v.21 no.3
• /
• pp.306-311
• /
• 2017

In the future ubiquitous network, information will collect data from various sensors in the field. Since the sensor nodes are equipped with small, often irreplaceable, batteries with limited power capacity, it is essential that the network be energy-efficient in order to maximize its lifetime. In this paper, we propose an effective network routing method that can operate with low power as well as the transmission of data and information obtained from sensor networks, and identified the number of sensors with the best connectivity to help with the proper placement of the sensor. These purposes of this research are the development of the sensor middle-ware to integrate the maritime information and the proposal of the routing algorithm for gathering the maritime information of various sensors. In addition, for more secure ship navigation, we proposed a method to construct a sensor network using various electronic equipments that are difficult to access in a ship, and then construct a communication system using NMEA(the national marine electronics association), a ship communication standard, in the future.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.22 no.7
• /
• pp.949-955
• /
• 2018

Hardware-in-the-loop (HIL) simulation is a technique that can be employed for developing and testing complex real-time embedded systems. HIL simulation provides an effective platform for verifying power management system (PMS) performance of liquefied natural gas carriers, which are high value-added vessels such as offshore plants. However, HIL tests conducted by research institutes, including domestic shipyards, can be protracted. To address the said issue, this study proposes a field programmable gate array (FPGA) based PMS-HIL simulator that comprises a power supply, consumer, control console, and main switchboard. The proposed HIL simulation platform incorporated actual equipment data while conducting load sharing PMS tests. The proposed system was verified through symmetric, asymmetric, and fixed load sharing tests. The proposed system can thus potentially replace the standard factory acceptance tests. Furthermore, the proposed simulator can be helpful in developing additional systems for vessel automation and autonomous operation, including the development of energy management systems.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.27 no.4
• /
• pp.538-549
• /
• 2021

In this study, a trim tab on the stern hull of a small high-speed vessel of approximately 10 m length sailing at a Froude number of 1.0 was designed for energy efficiency. The running attitude and resistance performance of the bare hull and trim tab hull at several angles to the base line were analyzed for model and full scale ships using computational fluid dynamics, and compared to investigate the scale effect. The analysis results for the bare hull were quite similar, but a difference in the attitude control under same conditions of the trim tab was observed, resulting in the total resistance error. However, there was no significant difference in tendency of the variation in the resistance with the attitude. Thus, the optimum running attitude could be determined from the tendency despite the scale effect, but a full scale analysis is required to analyze the control of the attitude by the trim tab and flow characteristics near the full scale ship.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2021.11a
• /
• pp.201-202
• /
• 2021

Regulations on greenhouse gases emitted from ships in international shipping are being strengthened, and the greenhouse gas reduction target established by the International Maritime Organization is acting as a great challenge for shipping companies in terms of technical and operational aspects. The International Maritime Organization aims to reduce carbon intensity by 30% by 2030, 70% by 2050, and by 50% in terms of gross emissions compared to 2008. To realize this situation, the IMO adopted some short-term and mid-to-long-term measures and adopted technical measures such as the application of EEXI, an energy efficiency index, to existing ships from 2023, and the early application of EEDI phase 3 for some tpe of ships. In addition, reduction measures were introduced to reduce greenhouse gas in the operational aspect.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.22 no.5
• /
• pp.554-563
• /
• 2016

Ships are capable of operating on residual fuel oil. Recently, various attempts have been made to meet environmental regulations and with ships operating on residual fuel oil. One way of fulfilling these requirements is by using fuel additives. Dispersants and fuel combustion improvers will have a positive effect on improving the combustion characteristics of the residual fuel oil. As such, this study examines fuel oils blended with additives by using fuel combustion analysis (FIA/FCA) and thermogravimetric analysis (TGA). The results of FIA/FCA focuse only on the amount of work done by the fuel oil. Therefore, it is recommended in this study that a new method to evaluate the combustion efficiency via FIA/FCA processes be developed. The analysis with ROHR curve gained by FIA/FCA brought similar results with pressure trace curve therefore it can be said that new analysis method can be reliable. The TGA, analysis process is very sensitive to the evaporation of fuel, for example, which could be addressed. In the performance-related findings of this study, blended samples with additives containing iron compounds showed a greater improvement in early combustion characteristics than samples without additives.

• Composites Research
• /
• v.34 no.1
• /
• pp.8-15
• /
• 2021

In the shipbuilding and marine industry, as a technology for reducing the weight of parts to reduce energy and improve operational efficiency of ships is required, a method of applying fibers-reinforced composites which is high-strength lightweight materials, as part materials can be considered. In this study, the possibility of applying fibers-reinforced composites to the pipe support clamps was evaluated to reduce the weight of LNGC. The fibers-reinforced composites were manufactured using carbon fibers and glass fibers as reinforcing fibers. Through the computer simulation program, the properties of the reinforcing materials and the matrix materials of the composites were inversely calculated, and the performance prediction was performed according to the change in the properties of each fiber lamination pattern. In addition, the structural analysis of the clamps according to the thickness of the composites was performed through the finite element analysis program. As a result of the study, it was confirmed that attention is needed in selecting the thickness when applying the fibers-reinforced composites of the clamp for weight reduction. It is considered that it will be easy to change the shape of the structure and change the structure for weight reduction in future supplementary design.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.28 no.4
• /
• pp.648-656
• /
• 2022

As environmental regulations such as the International Maritime Organization (IMO)'s strategy to reduce greenhouse gases(GHG) are strengthened, technology development such as eco-friendly ships and alternative fuels is expanding. As part of this, ship propulsion technology using energy reduction and wind propulsion technology is emerging, especially in shipping companies and shipbuilders. By securing wind propulsion technology and introducing empirical research into shipbuilding and shipping, a high value-added market using eco-friendly technology can be created. Moreover, by reducing the fuel consumption rate of operating ships, GHG can be reduced by 6-8%. Rotor Sail (RS) technology is to generate a hydrodynamic lift in the vertical direction of the cylinder when the circular cylinder rotates at a constant speed and passes through the fluid. This is called the Magnus effect, and this study attempted to propose a plan to increase propulsion efficiency through a numerical analysis study on turbulence flow characteristics around RS, a wind power assistance propulsion system installed on a ship. Therefore, C_L and C_D values according to SR and AR changes were derived as parameters that affect the aerodynamic force of the RS, and the flow characteristics around the rotor sail were compared according to EP application.