• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.22 no.6
• /
• pp.895-902
• /
• 2018

Energy consumption in buildings is close to 40% of the total national energy consumption in developed countries such as US and Japan, and Korea accounts for 24% of total energy consumption. In buildings, HVAC can't freely control the cooling flow rate according to the required calorie, so energy is not used efficiently. Therefore, by using the energy saving valve, the flow rate can be controlled by the required amount of heat and the energy can be saved. In this paper, we define basic conditions and develop control and monitoring boards for building energy saving valves based on PIC processor with low power and high cost-effectiveness. The designed board displays and transmits in real time information about two temperature values, flow values and calculated calories for temperature difference measurement. The developed board will be useful for real - time monitoring of the state of the valve in the future and development of the valve for the offshore.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.30 no.10B
• /
• pp.619-629
• /
• 2005

In this paper, we propose energy-aware routing schemes which are simple enough to be applicable to the wireless sensor networks. The one hop upstream no de in direction of the base-station is determined in four different ways based on the energy information of neighboring nodes, which are obtainable via the process of self-organization of the network. The fair distribution of the energy consumption over all the possible routes to the base-station is one of the design objectives. Also, an alternate route search mechanism is proposed to cope with the situation in which no routing information is available due to lack of remaining energy of the neighboring nodes. The mechanism turns out to be a supplementary scheme to improve the energy efficiency. Lots of simulations are performed to examine the performance metrics such as the energy efficiency, throughput, network lifetime, and the transmission latency of the proposed schemes. Simulation results show the feasibility of the simple routing schemes for the sensor networks.

• Journal of the Korean Solar Energy Society
• /
• v.39 no.3
• /
• pp.47-57
• /
• 2019

Clear sky indices were estimated by various ways based on in-situ observation and satellite-derived solar irradiance. In principle, clear sky index defined by clear sky solar irradiance indicates the impacts of cloud on the incoming solar irradiance. However, clear sky index widely used in energy sciences is formulated by extraterrestrial irradiance, which implies the extinction of solar irradiance due to mainly aerosol, water vapor and clouds drops. This study examined the relative difference of clear sky indices and then major characteristics of clear sky irradiance when sky is clear are investigated. Clear sky is defined when clear sky index based on clear sky irradiance is higher than 0.9. In contrast, clear sky index defined by extraterrestrial irradiance is distributed between 0.4 and 0.8. When aerosol optical depth and air mass coefficient are relative larger, solar irradiance is lower due to enhanced extinction, which leads to the lower value of clear sky index defined by extraterrestrial irradiance.

• Korean Journal of Materials Research
• /
• v.9 no.5
• /
• pp.446-451
• /
• 1999

Surface of Polymethylmethacrylate (PMMA) was modified by ion assisted reaction in which ion beam of Ar or$ O_2$is irradiated on polymer in reaction gas environment. Ion beam energy was changed from 600 to 1000eV, and ion doses were varied from $5\times10^{14} ions/cm^2 to 1\times10^{17} ions/cm^2$. Contact angle and surface energy of modified PMMA were measured by contact angle micrometer using distilled water and formamide. In the case of $Ar^+$ ion irradiation only, the contact angle reduced from $68^{\circ} to $35^{\circ}$ and the surface energy was changed from 46 dyne/cm to 60 dyne/cm. The contact angle significantly decreased to $14^{\circ}$and the surface energy increased to 72 dyne/cm when the surface of PMMA was modified by oxygen ion irradiation in oxygen gas environment. Improvement of wettability results from the formation of new hydrophilic group which is identified as C-O chain by XPS analysis. Recovery of wettability in dry air and maintenance of it in water condition were explained in view of the formation of hydrophilic group.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.5
• /
• pp.37-42
• /
• 2004

Shallow $p^{＋}$-n junctions were formed by preamorphization, low-energy ion implantation and dual-step annealing processes. Germanium ions were implanted into silicon substrates for preamorphization. The dopant implantation was performed into the preamorphized and non-preamorphized substrates using B $F_2$2 ions. Rapid thermal anneal (RTA) and furnace anneal (FA) were employed for dopant activation and damage removal. Samples were annealed by one of the following four methods; RTA(75$0^{\circ}C$/10s)＋Ft FA＋RTA(75$0^{\circ}C$/10s), RTA(100$0^{\circ}C$/10s)＋FA, FA＋The Ge Preamorphized sample exhibited a shallower junction depth than the non-preamorphized sample. When the employed RTA temperature was 100$0^{\circ}C$, FA＋RTA annealing sequence exhibited better junction characteristics than RTA＋FA thermal cycle from the viewpoint of junction depth, sheet resistance, $R_{s}$$.$ $x_{j}$, and leakage current.t.

• 한국태양에너지학회:학술대회논문집
• /
• 2012.03a
• /
• pp.177-181
• /
• 2012

본 연구는 고온고습 시험을 통하여 Cell 레벨에서의 표면관찰 및 효율저하를 분석하였다. 고온고습 시험 조건은 KS C IEC-61215에서 제시한 PV module하의 조건을 이용하여 온도 $85^{\circ}C$, 습도 85% 조건하에 1000시간 동안 수행하였다. 고온고습 시험에 따라 효율에 직접적인 영향을 줄 수 있는 이상 유 무를 Cell 표면을 통해 분석한 결과, 고온고습 시험 수행 중 부분적으로 변색되는 것을 확인하였다. 고온고습 시험 전 단결정 Cell의 효율은 17.74% 였으며, 1000시간 수행 후 15.63%으로 11.89%의 감소율을 보였다. 다결정 Cell의 시험 전 효율은 15.46%, 1000시간 수행 후 효율은 14.02%로 9.31%의 감소율을 보였다. 경년 시 나타나는 전기적 특성을 분석하기 위해 FF(Fill Factor)값을 분석한 결과, 고온고습 시험 전 단결정 Cell은 78.71%에서 75.01%로 4.7%의 감소율을 보였으며, 다결정 Cell은 78.10 %에서 76.66%로 1.84%의 감소율을 보였다. 효율 및 FF값에서 단결정 Cell이 다결정 Cell보다 감소율이 큰 것으로 분석되었으며, 이는 단결정 Cell이 외부 환경에서 더욱 크게 작용하여 효율저하에 영향을 주었다고 판단된다.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.20 no.4
• /
• pp.159-163
• /
• 2010

Co-(0.5 mol%) and Ce-(0~0.3 mol%) doped cubic zirconia ($ZrO_2:Y_2O_3$=64:36 mol%) single crystals grown by a skull melting method were heat-treated in $N_2$ at $1200^{\circ}C$ for 3 hrs. The brown-colored as-grown single crystals were changed into either green or blue color after the heat treatment. Before and after the heat treatment, the YSZ (yttriastabilized zirconia) single crystals were cut for wafer form (${\phi}7mm{\times}t2mm$) and round brilliant cut ($\phi$ 12 mm). The optical and structural properties were examined by UV-VIS spectrophotometer and X-ray diffraction. Absorption by $Ce^{3+}(^2F_{5/2},\;_{7/2}(4f){\rightarrow}^2T_g(5d^1)),\;Co^{2+}(^4A_2(^4F){\rightarrow}^4T_1(^4F)$ or $^4T_1(^4P))$ and $Co^{3+}$, change of ionization energy and lattice parameter were confirmed.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.34 no.1
• /
• pp.36-39
• /
• 2024

As interest in power semiconductors is growing recently, research on device design and application using light energy gap materials such as SiC and GaN is being actively conducted. Because AlN single crystals have a larger energy gap than the above mentioned materials, research on high-power devices is also in progress, but commercialized wafers have not yet been reported, so research is needed. In this study, we applied the HVPE (Hydride vapor phase epitaxy) method to produce AlN single crystals and attempted to obtain bulk single crystals using our own manufacturing equipment. To this end, we would like to report the results of securing the growth conditions for single crystals. we would like to report on the change in the shape of the grown crystal according to the change in temperature.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.11a
• /
• pp.158.1-158.1
• /
• 2010

국내 최초의 생활폐기물고형연료(RDF) 생산플랜트인 원주시 RDF플랜트의 2009년도 운영실적을 정리하여 폐기물 처리단가를 분석하였으며 에너지 생산 효과도 분석하였다. 실적분석에 사용된 자료는 원주 RDF플랜트 위탁운영업체가 운영비를 청구 및 정산하기 위해서 원주시에 상시 측정 및 보고하는 항목으로서, 내용은 트럭으로 플랜트에 반입되는 폐기물 전체량, RDF생산 전체량, 불순물 매립 전체량, 건조 및 탈취용 연료사용 전체량, 전기사용 전체량 등이다. 2009년도 원주시 RDF플랜트에 반입된 폐기물 량은 총 17,504톤이었고, RDF를 총 7,044톤 생산하였으며, 4,120톤의 불연물을 선별하였다. 1년간 사용한 건조 및 탈취용 연료는 총 596,268 리터였으며 연료인 부생유의 가격은 리터 당 평균 864.6원이었다. 사용한 전기량은 총 2,435,397 kWh였고, 이 중에서 성형공정에 사용된 전기량은 총 사용량의 19%였다. 이상의 기록자료들을 분석해 본 결과, 폐기물 1톤을 처리하는데 전기 비용이 14,334원이었고, 연료비가 29,452원이었다. 여기에 폐기물 1톤당 불연물 매립비 6,573원과 위탁인건비를 합하면 폐기물 1톤당 처리비용은 약 116,573원으로 나타났다. 현재 원주시 RDF는 톤당 25,000원에 판매되고 있으므로 이 비용을 감안하면 폐기물 1톤당 처리비용은 105,298원으로 산출되었다. 현재 알려진 유사 규모의 소각로 운영비가 폐기물 1톤당 136,736원인데, 이것은 RDF기술보다 31,438원/톤-폐기물 정도 처리비용이 비싸다. 따라서 100톤 이하 규모의 폐기물처리시설 설치를 할 경우에는 RDF 시설이 경제적으로 타당함을 나타낸다. 원주시 RDF플랜트의 물질수지를 분석해 본 결과, RDF생산 수율은 40.2%였으며 총 투입된 에너지는 8,0587 Gcal였다. 생산된 에너지 총량은 RDF발열량 4,500 kcal/kg으로 했을 때 31,699 Gcal로 나타났다. 투입대비 생산에너지 비율은 25.4%로 계산되었고, 전기의 발전효율을 40%로 감안했을 경우에는 35.3%로 계산되었다. 성형하는데 사용되는 총 에너지는 전체 투입에너지의 4.9%로 나타났고, 비용으로는 폐기물 1톤당 2,723원 이었다.

• Journal of Energy Engineering
• /
• v.5 no.2
• /
• pp.170-175
• /
• 1996

This study is to determined the activation energy from TGA experimental data for the bituminous and anthracite coals of three kinds which are being used in the domestic coal-fired power plants. TGA experimental data indicate that the weight loss temperature of bituminous coal is 200$^{\circ}C$ higher than that of anthracite coal. Activation energy of bituminous coal is in the range of 14∼20 Kcal/mole compared with 37∼55 Kcal/mole of anthracite coal. A reduction of particle size of coals results in the decrease of activation energy and activation energy has a good correlation with the weight loss percent of coal in the TGA experiment. Addition of CaCO$_3$ on anthracite coal caused to decrease the activation energy of 1∼23 Kcal/mole while activation energy of bituminous coal do not change significantly.