• Applied Chemistry for Engineering
• /
• v.10 no.1
• /
• pp.98-104
• /
• 1999

In this work, we investigated hydrogen content, bond structure, and electrical properties of a-Si:H films prepared by ECR plasma CVD as a function of pressure. In general, the photo sensitivity of a-Si:H films prepared by CVD method decreases as the deposition rate increases, but the photo sensitivity of a-Si:H films prepared by ECR plasma deposition method increases as the deposition rate increases. In the same condition of microwave power, the ratio of $SiH_4/H_2$, and pressure, though film thickness increases linearly with deposition time and hydrogen content in the film is constant, photo conductivity can be decreased because $SiH_2$ bond is made more than SiH bond in the short reaction time. According to increase pressure in the chamber, SiH bond in the film increase and optical energy gap decrease. So, photo conductivity can be increased. But photo sensitivity decreased as dark conductivity increase. It must be grown in the condition of low pressure and hydrogen gas for taking the a-Si:H film of high quality.

• Journal of the Korean Vacuum Society
• /
• v.10 no.1
• /
• pp.104-111
• /
• 2001

B-doped hydrogenated amorphous silicon carbide (a-SiC:H) thin films were prepared by plasma-enhanced chemical-vapor deposition in a gas mixture of $SiH_4, CH_4,\;and\; B_2H_6$. Physical and chemical properties of a-SiC:H films grown with varing the ratio of $B_2H_6/(SiH_4+CH_4)$ were characterized with various analysis methods including scanning electron microscopy (SEM), X-ray diffractometry (XRD), Raman spectroscopy, Fourier-transform infrared (FTIR) spectroscopy, secondary ion mass spectroscopy (SIMS), UV absorption CH_4spectroscopy and electrical conductivity measurements. With the B-doping concentration, the doping efficiency and the micro-crystallinity were decreased and the film became amorphous when $B_2H_6/(SiH_4{plus}CH_4)$ was over $5{\times}10^{-3}$. The addition of $B_2H_6$ gas during deposition decreased the H content in the film by lowering the quantity of Si-C-H bonds. Consequently, the optical band gap and the activation energy of a-SiC:H films were decreased with increasing the B-doping level.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.10a
• /
• pp.42.1-42.1
• /
• 2011

박막형 디스플레이구서에 있어서 투명전극은 필수적이다. 투명전극은 정보를 표시하기 위해 빛을 외부로 방출시키거나 태양광 등을 소자 내부로 입사시켜야 한다. 또한 전극을 형성하는 박막은 높은 광투과율과 ${\sim}10-4{\Omega}cm$ 정도의 낮은 전기비저항을 가져야 한다. 가장 널리 사용되는 투명전극으로 ITO (Indium Tin Oxide)는 인듐의 독성, 저온증착의 어려움, 스퍼터링시 음이온 충격에 의한 막 손상으로 저항의 증가 및 액정디스플레이의 투명전극으로 사용될 경우 $400^{\circ}C$정도의 높은 온도와 수소플라즈마 분위기에서 장시간 노출시 열화로 인한 광학적 특성변화가 문제로 지적된다. 이러한 문제 해결의 대안으로 ZnO 산화물 반도체가 있는데 ITO 박막에 비해 비저항이 높기 때문에 도핑을 이용한 비저항을 ${\sim}10-4{\Omega}cm$ 정도로 낮추어야 한다. 투명전도막으로는 ITO, FTO 등과 더블어 체적 저항율은 다소 높으나 환원성 분위기에 대한 내성, 가시광 영역에서의 높은 광투과율과 저렴한 가격 등의 장점 등으로 AZO 박막이 주목 받고 있다. ZnO는 ITO 나 FTO에 비해서 700 kJ/mol의 큰 분해에너지를 가지므로 코팅 때 발생하는 전도도 및 투과율이 나빠지는 현상이 발생하지 않는 특징이 있으며, 위의 두 재료에 비해 밴드갭도 가장 낮아서 자외선 투과율이 낮다. 그러나 내습성이 약하기 때문에 이를 보완하기 위하여 내습성향상과 전도성 향상을 위해서 3족 원소인 B, In, Al, Ga 등을 도핑한 ZnO 투명전도막의 연구가 진행되고 있다. 이러한 원소들 중에서 Al로 도핑했을 때 가장 낮은 비저항을 얻을 수 있다고 알려져 있다. 본 연구에서는 SiOC 박막위에 AZO 박막을 제조하기 위하여 RF 마그네트론 스퍼터링법을 이용하여 박막을 성장시켰으며, 박막의 전기적 및 광학적 특성을 조사하였다. AZO 박막은 rf power가 5~200 W인 RF 마그네트론 스퍼터 방법에 의해서 제작되었다. SiOC 박막은 산소와 DMDMOS 전구체의 유량비를 다르게 하여 플라즈마 발생 화학적 기상 증착방법으로 증착되었다. 증착된 SiOC박막은 UV visible spectroscopy에 의해서 분석하였다. 투명전극의 비저항은 rf 전력이 작을 수록 낮았으며, SiOC 절연막 위에 AZO를 증착시킨 후 반사률은 반대로 바뀌는 것을 확인하였다.

• Journal of the Korean Vacuum Society
• /
• v.16 no.2
• /
• pp.105-109
• /
• 2007

In this paper, we fabricated TCO (transparent conductive oxide) electrode on flexible substrate in order to study effects of electrical and optical properties according to Al-doped ZnO(AZO) film thickness. The thickness of film was from 100 nm to 500 nm and was controlled by changing deposition time. We used High Resolution X-ray Diffractometer (HR-XRD) to analyze crystal structure and UV-visible spectrophotometer to measure property of optical transmittance, respectively. The surface images are obtained by using ESEM (Environment Scanning Electron Microscopy). In this experiment, all the AZO films deposited on flexible substrate show high transmittance over 90% and especially in the films with 400 nm and 500 nm thickness, the resistivity ($4.5{\times}10^{-3}\;{\Omega}-cm$) and optical bandgap energy (3.61 eV) are superior to the other films.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.15 no.7
• /
• pp.1559-1563
• /
• 2011

We fabricated gallium doped ZnO (GZO, 5 wt% Ga) thin films on PES (polyethersulfon) substrate with RF magnetron sputtering and investigated optical and electrical properties for various substrate temperatures ($50{\sim}200^{\circ}C$). All GZO thin film has c-axis preferred orientation without reference to deposition conditions. As a result of AFM analysis, the GZO thin film deposited at $200^{\circ}C$ exhibited the lowest surface roughness of 0.196nm. The transmittance of GZO thin films were above 80% and Burstein-Moss effect was observed. In the analysis of Hall measurement, we confirmed that the GZO thin film deposited at $200^{\circ}C$ showed the lowest resistivity of $6.93{\times}10-4{\Omega}{\cdot}cm$ and the highest carrier concentration of $7.04{\times}1020/cm^3$.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.14 no.7
• /
• pp.1647-1652
• /
• 2010

A CdS film has been used as a window layer in CdTe and Cu(In,Ga)$Se_2$ thin films solar cell. Partial substitution of Zn for Cd increases the photocurrent and the open-circuit voltage by providing a match in the electron affinities of the two materials and the higher band gap. In this paper, CdZnS/CdTe and CdS/CdTe heterojunctions were fabricated and the electrical characteristics were investigated. Current-voltage-temperature measurements showed that the current transport for CdS/CdTe heterojunction was controlled by both tunneling and interface recombination. However, CdZnS/CdTe heterojunction displayed different current transport mechanism with the operating temperature. For above room temperature, the current transport of device was generation/recombination in the depletion region and was the leakage current and/or tunneling in the range below room temperature.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.19 no.6
• /
• pp.1393-1398
• /
• 2015

In this study, the electrical and optical properties of GZO (Ga-doped ZnO) thin films prepared on PES substrates by RF magnetron sputtering method with various working pressures (5 to 20 mTorr) were investigated. All GZO thin films exhibited c-axis preferential growth regardless of working pressure, the GZO thin film deposited at 5 mTorr showed the most excellent crystallinity having 0.44˚ of FWHM. In AFM observations, surface roughness exhibited the lowest value of 0.20 nm in a thin film produced by the working pressure 5 mTorr. Figure of merits of GZO thin film deposited at 5 mTorr showed the highest value of 6652, in this case resistivity and average transmittance in the visible light region were 6.93×10^-4Ω-cm and 81.4%, respectively. We could observed the Burstein-Moss effect that carrier concentration decrease with the increase of working pressure and thus the energy band gap is narrowed.

• Journal of the Korean Vacuum Society
• /
• v.7 no.3
• /
• pp.187-194
• /
• 1998

InGaAsP epitaxial layers lattice matched to InP were grown at 600 and $620^{\circ}C$ by low pressure metalorganic chemical vapor deposition. Solid phase composition of group III was controlled by the diffusion flux gas phase to the reachion surface. For the case of group V, the difference of As and P vapor pressure and pyrolysis efficiency of $PH_3$and $AsH_3$ mainly determined their in corporation into solid. An abnormal behavior of peak energy shift was observed below 75K in temperature variant photoluminescence study. This abnormal behavior was explained by the difference in order of ordering which makes spatial variation of energy gap in InGaAsP layer and this explanation was supported by the analyses of transmission electron microscopy and transmission spectroscopy.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.475-475
• /
• 2013

Cuprous oxide ($Cu_2O$)는 밴드갭이 2.17 eV p-type 산화물 반도체로써 태양에너지 변환기, photocatalysis (광촉매작용), 센서, 스위칭 메모리 등 응용이 다양한 재료이다. 산화물 반도체의 기본 특성은 나노/마이크로 범위 안에서 재료의 표면형태, 크기, 구조와 형상 공간방향등에 크게 영향을 받는다. 그렇기 때문에 원하는 $Cu_2O$ 특성을 얻기 위해서 성장 거동을 아는 것은 매우 중요하다. RF 마그네트론 스퍼터법으로 rod 성장 사례는 잘 알려지지 않았다. 그래서 RF 마그네트론 스퍼터법 $Cu_2O$ rod 형성 실험을 통하여 $Cu_2O$ 형성과 성장 거동을 알아보았다. RF 마그네트론 스퍼터법으로 $Cu_2O$ rod를 glass 기판 위에 Cu metal target을 이용하여 형성시켰다. $Cu_2O$ rod 합성을 위해 기판온도 및 산소분압 O2/(Ar+O2)=3%, 5%, 7% 증착시간 등을 변화시켜 실험하였다. 성장된 rod의 분석은 XRD, SEM으로 확인하였다. 성장 거동은 증착온도와 증착시간에 차이를 보였다. 증착온도 $550^{\circ}C$에서 rod가 생성되는 것을 관찰하였다. 증착시간이 길어질수록 rod 길이가 길어지고 일정 시간이 지나면 rod의 길이 성장보다는 두께(폭)가 성장하는 것을 확인하였다. 증착온도 $550^{\circ}C$ 그리고 산소분압 3%, 5%, 7% 조건에서 rod 합성 실험을 하였을 때 3%, 5% 조건에서 rod의 성장을 확인하였다. 이때 3%, 5% 산소분압에 따라 rod의 모양이 변화하였다. 하지만 7% 조건에서는 rod가 성장하지 않았다. 이유는 3%, 5%에서는 Cu metal peak을 확인하였지만, 7% 조건에서는 Cu metal peak이 없었다. 이로부터 Cu metal이 $Cu_2O$ rod 생성에 영향을 미치는 중요한 요소임을 예상할 수 있었다.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.22 no.2
• /
• pp.114-119
• /
• 2008

With the improvement of industrial society, the high quality electrical energy, simplification of operation and maintenance, ensuring reliability are being required. We request urgently change a $SF_6$ for an environment friendly gas insulation material. In this paper the experiments of breakdown characteristics by pressure and gap change of Imitation-Air in model GIS(Gas Insulated Switchgear) were described. Also assess of breakdown characteristics about Imitation-Air and $SF_6$. It is considered in this paper that the results are fundamental data for electric insulation design of Distribution Power Facilities which will be studied and developed in the future. The pressure to be confronted to $SF_6$ gas 1[atm] for Distribution Power Facilities is Imitation-Air 3[atm]. And we could make an environment friendly gas insulation material with maintaining dielectric strength by Imitation-Air which generates a lower level of the global warming effect.