• Proceedings of the Korean Society Of Semiconductor Equipment Technology
• /
• 2003.12a
• /
• pp.105-108
• /
• 2003

본 논문은 파이렉스 #7740 유리박막을 이용한 MEMS용 MLCA와 Si기판의 양극접합 특성에 관한 것이다. 최적의 RF 마그네트론 스퍼터링 조건(Ar 100 %, input power $1W/\textrm{cm}^2$)하에서 MLCA 기판위에 파이렉스 #7740 유리의 특성을 갖는 박막을 증착한 후 600 V, $400^{\circ}C$에서 1시간동안 양극접합했다. 그 다음에 Si 다이어프램을 제조한 후, MLCA/Si 접합계면과 MLCA 구동을 통한 Si 다이어프램 변위특성을 분석 및 평가하였다. 다이어프램 형상에 따라 정밀한 변위 제어가 가능했으며 0.05-0.08 %FS의 우수한 선형성을 나타내었다. 또한, 측정동안 접합계면 균열이나 계면분리가 일어나지 않았다. 따라서, MLCA/Si기판 양극접합기술은 고성능 압전 MEMS 소자 제작공정에 유용하게 사용가능할 것이다.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.6
• /
• pp.1187-1193
• /
• 2002

Anodic bonding process has been quantitatively evaluated based on the Taguchi analysis of the interfacial fracture toughness, measured at the interface of anodically bonded silicon-glass bimorphs. A new test specimen with a pre-inserted blade has been devised for interfacial fracture toughness measurement. A set of 81 different anodic bonding conditions has been generated based on the three different conditions for four different process parameters of bonding load, bonding temperature, anodic voltage and voltage supply time. Taguchi method has been used to reduce the number of experiments required for the bonding strength evaluation, thus obtaining nine independent cases out of the 81 possible combinations. The interfacial fracture toughness has been measured for the nine cases in the range of 0.03∼6.12 J/㎡. Among the four process parameters, the bonding temperature causes the most dominant influence to the bonding strength with the influence factor of 67.7%. The influence factors of other process parameters, such as anodic voltage and voltage supply time, bonding load, are evaluated as 18%, 12% and 2.3%, respectively. The maximum bonding strength of 7.23 J/㎡ has been achieved at the bonding temperature of 460$\^{C}$ with the bonding load of 45gf/㎠, the applied voltage of 600v and the voltage supply time of 25minites.

• Journal of Sensor Science and Technology
• /
• v.12 no.6
• /
• pp.265-272
• /
• 2003

This paper describes anodic bonding characteristics of MLCA (Multi Layer Ceramic Actuator) to Si-wafer using evaporated Pyrex #7740 glass thin-films for MEMS applications. Pyrex #7740 glass thin-films with same properties were deposited on MLCA under optimum RF magneto conditions(Ar 100%, input power $1\;W/cm^2$). After annealing in $450^{\circ}C$ for 1 hr, the anodic bonding of MLCA and Si-wafer was successfully performed at 600 V, $400^{\circ}C$ in - 760 mmHg. Then, the MLCA/Si bonded interface and fabricated Si diaphragm deflection characteristics were analyzed through the actuation test. It is possible to control with accurate deflection of Si diaphragm according to its geometries and its maximum non-linearity is 0.05-0.08 %FS. Moreover, any damages or separation of MLCA/Si bonded interfaces do not occur during actuation test. Therefore, it is expected that anodic bonding technology of MLCA/Si wafers could be usefully applied for the fabrication process of high-performance piezoelectric MEMS devices.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2003.11a
• /
• pp.214-217
• /
• 2003

상하로 양극 영역이 중첩된 새로운 Si 포토다이오드를 제작하고 이의 전기광학적 특성을 조사하였다. 제작된 소자의 역포화전류와 이상계수는 각각 68pA와 1.8로 나타났으며 -3V 바이어스에서 측정된 접합 커패시턴스는 8.3 pF로 나타났다. 또한 $100mW/cm^2$, AMI 스펙트럼 조건에서 -3V 바이어스 아래 측정된 광전류와 감도특성은 각각 $60\;{\mu}A$와 6 A/W로 나타났다.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.41 no.6
• /
• pp.423-427
• /
• 2017

In this paper, an anchor design that improves bonding strength uniformity in the silicon-on-glass (SOG) process is presented. The SOG process is widely used in conjunction with electrode-patterned glass substrates as a standard fabrication process for forming high-aspect-ratio movable silicon microstructures in various types of sensors, including inertial and resonant sensors. In the proposed anchor design, a trench separates the silicon-bonded area and the electrode contact area to prevent irregular bonding caused by the protrusion of the electrode layer beyond the glass surface. This technique can be conveniently adopted to almost all devices fabricated by the SOG process without the necessity of additional processes.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.3
• /
• pp.681-686
• /
• 2017

Degradation is commonly observed in field-aged PV modules due to corrosion of the photovoltaic ribbon. The reduced performance is caused by a loss of fill factor due to the high series resistance in the PV ribbon. This study aimed to mitigate the degradation by corrosion using five sacrificial anodes - Al, Zn and their alloys - to identify the most effective material to mitigate the corrosion of the PV ribbon. The corrosion behavior of the five sacrificial anode materials were examined by open circuit potential measurements, potentiodynamic polarization tests, and galvanic current density and potential measurements using a zero resistance ammeter. Immersion tests for 120 hours were also conducted using materials and damp heat test tests were performed for 1500 hours using 4 cell mini modules. The Al-3Mg and Al-3Zn-1Mg sacrificial anodes had a low corrosion rate and reduced drop in power, making then suitable for long-term use.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.15 no.1
• /
• pp.9-20
• /
• 2002

The purpose of this research is to develop computational procedures for studying nonlinear soil-structure interaction Problems. In orders to study soil-structure interaction behavior, the finite element analysis for the strip footing subjected to both vortical and lateral loads, and foundation layer reinforced with sheet pile are considered, interface elements are used between the footing and the soil to model the interaction behavior The main analyzed results are as follows; 1. For the prediction of settlement and lateral displacement, the result due to interface element was evaluated larger then without interface element. 2. For the determination of ultimate bearing capacity, the value using interface element appeared smaller by 12%, which was safe. 3. The horizontal and vertical displacement of strip footing affected by the presence of interface element.

• Korean Journal of Optics and Photonics
• /
• v.17 no.4
• /
• pp.354-358
• /
• 2006

A silicon lens and an insulator of pyrex, components of a micro-electron column, should be assembled by aligning and stacking simultaneously. An optical alignment of a diffraction beam and a laser welding were employed for the assembly of a source lens and an Einzel lens with precision within $\pm$4% for the maximum aperture size. The experimental condition for optical alignment and laser welding are explained. Anodic bonding was used to assist in stacking lenses. A micro-electron column of smaller apertures assembled with precise alignment and fabrication was tested with a current image of a Cu grid of 9$\mu$m in linewidth, and showed a higher resolution in acceleration mode.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.11
• /
• pp.211-220
• /
• 2002

Optical disk drives read information by replacing a laser beam on the disk track. As information has become larger, the more accurate position control of a laser beam is necessary. In this paper, we report the analysis and fabrication of the micro mirror for optical disk drivers. A coupled simulation of gas flow and structural displacement of the micro mirror using the Finite-Element-Method is applied to this. The mirror was fabricated by using MEMS technology. Especially, the process using the lapping and polishing step after the bonding of the mirror and electrode plates was employed for the Process reliability. The mirror size was 2.5mm${\times}$3mm and it needed about 35V for displacement of 3.2 ${\mu}$.

• Proceedings of the IEEK Conference
• /
• 2003.07b
• /
• pp.1037-1040
• /
• 2003

본 논문에서는 microcolumn 을 위한 초소형 전자빔 deflector 의 제작방법과 microcolumn array 에서 deflector 의 외부 패드를 최소화 할 수 있는 새로운 배선방법을 기술하였다. 배선의 통로 및 절연체 역할을 하는 Pyrex glass 의 양쪽에 각각 실리콘 웨이퍼의 양극접합 및 deep reactive ion etching(DRIE)과 금속 전기 도금을 이용하여 다층배선을 하였다. 이 배선방법을 이용하면 microcolumn array 가 수백개가 되더라도 deflector 의 외부 패드는 항상 8개를 유지할 수 있다.