• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.312-313
• /
• 2008

A transflective liquid crystal displays associated with fringe field switching (FFS) mode of new concept is proposed. The device utilizes unique characteristic of the FFS mode in which the rotation angle of LC director is strongly dependent on electrode position in on state. We use the liquid crystal with negative dielectric anisotropy. Also we are look for optimized electrode size and the optimization of pixel electrode width and distance between them, the LC director could rotate about $22.5^{\circ}$ and $45^{\circ}$ depending on electrode positions. Consequently, we get high transmittance and high reflection on the optimized electrode condition. Respectively, a high image quality transflective display with single gap and single gamma characteristics realized.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.05a
• /
• pp.181-184
• /
• 2005

In this paper, we have improved a novel fast response time liquid crystal operating mode using tilt angle in the unique condition by hot-plate equipment. The new control of tilt angle for nematic liquid crystal (NLC) with negative and positive dielectric anisotropy on the rubbed homeotropic polyimide (PI) using baking method by Hot-plate equipment was investigated. LC tilt angle decreased with increasing baking temperature and time. Especially, the low LC tilt angle of positive type NLC (${\Delta}n$>0) on the rubbed homeotropic PI surface by increasing temperature and time was measured. The EO characteristics of the high tilted OCB(HTOCB) mode using control of tilt angle on the homeotropic surface than that of conventional OCB cell can be improved. We suggest that the developed the HTOCB cell using control of tilt angle on the homeotropic surface is a promising technique for the achievement of a fast response time and a high contrast ratio.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.6
• /
• pp.111-118
• /
• 2008

In this paper, novel latch-up prevention method that employs power-up sequential switches has been proposed to relieve latch-up problem in liquid crystal display (LCD) driver ICs. These sequential switches are inserted in the 2'nd and 3'rd boosting stages, and are used to short the emitter-base terminals of parasitic p-n-p-n circuit before relevant boosting stages are activated during power-up sequence. To verily the performance of the proposed method, test chips were designed and fabricated in a 0.13-um CMOS process technology. The measurement results indicated that, while the conventional LCD driver If entered latch-up mode at $50^{\circ}C$ accompanying a significant amount of excess current, the driver IC adopting the proposed method showed no latch-up phenomenon up to $100^{\circ}C$ and maintained normal current level of 0.9mA.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.18 no.2
• /
• pp.41-54
• /
• 2000

Photochemical modulation of Bragg-reflection wavelengths based on isomerization of an azobenzene (Azo) and subsequent change in reflectance was investigated in cholesteric liquid crystals (ChLCs) which reflect light in visible wavelength region. Irradiation at 366 nm, which causes an efficient transcis isomerization of Azo, led to change in reflected color of ChLCs toward shorter wavelengths with a concomitant lowering of phase transition. Reversible change in color was induced all-optically by alternate irradiation at effective wavelengths for reversible isomerization of Azo. A considerable variation in reflectance was also observed when the photoinduced change in color was measured by a probe light with the same handedness as the ChLCs. The spectral Position of selective light reflection in the initial states played an important role to produce a normal-mode and a reverse-mode switching in photoinduced modulation of reflectance of the ChLCs with respect to the probe light.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.33B no.1
• /
• pp.49-56
• /
• 1996

In this paper, as a new grey scale method for simple matrix LCDs, the grey scale method using the new code scheme was proposed. The experiment and the characteristic estimation for the new grey scale method were performed by the simulation of the 16 and 32 grey patterns and the calculation of the driving voltages. As a result of the experiment and the characteristic estimation, the 16 grey mode using the 3 bits code scheme, (7, 5, 3) has the maximum driving voltage which is reduced by 19% and 9.6% each compared with the values in the conventional grey modes discussed in this paper. And the extent of improvement in the driving voltage characteristics is increased much as the number of grey levels increases. On the other hand, as a result of the grey image estimation through the grey pattern simulation, the 3 bits 16 grey mode degrades the characteristics of the grey image more or less compared with the conventional grey method but the extent of this characteristic degradation is much reduced with the increase in the number of grey levels such as 32 grey scale, etc. Consequently the grey scale method using the new code scheme proposed in this paper is confirmed as a method that it minimized the degradation of grey characteristics and improves the driving voltage characteristics effectively.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.162-162
• /
• 2009

Optical bounce which occurs by over twist of the liquid crystal (LC) director has a problem of response time in fringe-field switching (FFS) modes. After removing the electric field, effective birefringence ($d{\Delta}n_{eff}$) at the edge of pixel electrode meets the $\lambda/2$ phase instantly, since tilt angle of LC directors at that position suddenly decreases compared to twist angle. In this paper, based on the careful analysis, origin of optical bounce has been explained.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.04a
• /
• pp.63-64
• /
• 2009

Optical bounce during switching in the fringe field switching (FFS) mode using a liquid crystal (LC) with positive dielectric anisotropy has been observed. According to the analysis, it occurs at two positions which are center and edge of the pixel electrode, which decreases decaying response time. The former is major and mainly associated with increase in twist angle instantaneously during switching off resulted from decrease in tilt angle near by LC molecules at center. This paper discusses the origin of such optical bounces.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.3
• /
• pp.311-318
• /
• 2004

We have studied electro-optic characteristics as a function of pretilt angle ($\theta$$_{p}$) in the fringe-field switching (FFS) mode using the LC with positive dielectric anisotropy. When $\theta$$_{p}$ is increased from 0$^{\circ}$ to 20$^{\circ}$, a maximum transmittance and an operating voltage are obviously decreased. In the viewing angle characteristics, the cell with low pretilt angle has a wide region for the contrast ratio greater than 5 and has a best luminance uniformity. Therefore, in the FFS device, a low pretilt angle is favored for high transmittance and wide viewing angle.gle.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.8
• /
• pp.720-725
• /
• 2002

The fringe-field switching (FFS) mode was known to exhibit both a wide viewing angle and high transmittance, especially when using the liquid crystal (LC) with negative dielectric anisotropy. In the device, the LC director rotates almost in-plane. However, in the bright state the device shows bluish and yellowish color along parallel and perpendicular to the LC director at off-normal directions since the LC director rotates only in one direction. Such a problem was greatly improved using a wedge shape of only pixel electrodes. In this way two different field directions exist in a pixel, enabling the LC director to rotate in two opposite directions. Consequently, owing to dual domain effect when using the LC with negative dielectric anisotropy, the viewing angle characteristics are greatly improved.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.05a
• /
• pp.153-156
• /
• 2004

We have studied electro-optic characteristics of transflective liquid crystal display (LCD) using in-plane switching mode. Unlike previous transflective LCD using a dual gap structure and multi driving circuit, this transflective LCD has a single gap structure and a single driving circuit. In the voltage on state, the electric field is applied horizontally to the LC directors, and then homogeneously aligned LC directors at initial state is rotated to with the electric field. But the twist angle of the LC directors in reflective area is lower than transmissive area. As a result, it is possible to design the transflective LCD with a single gap and a single driving circuit. The transflective display associated with this LC cell exhibits a wide viewing angle in both reflective and transmissive areas.