• The Journal of Engineering Geology
• /
• v.18 no.4
• /
• pp.405-414
• /
• 2008

When we evaluate slope stability, we regard the slope homogeneous and evaluate slope stability at the most dangerous portion of slope. However, since conditions and properties of rock mass/soil are different from one location to another within a single slope, slope stability evaluated by current concept can not represent slope correctly. This also result in over-reinforcement at the portion where reinforcement is not necessary. In order to solve these problems, we suggest a cell unit evaluation method in which we apply small rectangular cells in a slope and regard each cell as a single slope. In this method, slopes are classified into soil slope and rock slope depending on materials. Strength of rock, volumetric joint count, spacing of joints, condition of joints, ground water condition and so on are examined and SMR and condition index values are calculated. Finally, all data and results are presented as contour maps. We apply the cell unit evaluation method into 3 cut slopes. SMR values estimated by the new method are larger than those by current concept at most portions of slope, indicating that the new method suggested by this research represent slope stability more correctly than methods which were used. This method will prevent over-reinforcement at the portion of slope where reinforcement is not necessary.

• Journal of the Korean Geotechnical Society
• /
• v.20 no.8
• /
• pp.15-27
• /
• 2004

Sliding aspects of rock slope, where large-scaled tension cracks are induced during preliminary excavation, have been analyzed. Structure of rock mass is investigated by performing the electrical resistivity survey and the orientations and positions of discontinuities are measured from DOM-drilled core log. Geological evidence far primary failure movement has been detected and clay minerals which possess swelling properties are identified through XRD analysis. Slope stability is examined by considering the orientations of discontinuities and their trace distributions on the cut-face and neighboring natural slope surface. Both orientations and positions of failure-invoking discontinuity planes, traces of which are exposed within the anticipated sliding region, are concerned fur analyzing the preferred sliding directions. Regional sliding vectors are assessed based on the relative positions of potential sliding planes in the boreholes and the general trend of anticipated failure movement of rock slope is also investigated.

• Tunnel and Underground Space
• /
• v.13 no.4
• /
• pp.294-303
• /
• 2003

The structural behaviour of rock mass structure, such as tunnel or slope is critically dependent on the various characteristics of discontinuities. Therefore, it is important to survey and analyze discontinuities correctly for the design and construction of rock mass structure. One inevitable Procedure of discontinuity survey and analysis is joint set identification from a lot of raw directional joint data. The identification procedure is generally done by a graphical method. This type of analysis has some shortcomings such as subjective identification results, inability to use extra information on discontinuity, and so on. In this study, a computer program for joint set identification based on the fuzzy clustering algorithm was implemented and tested using two kinds of joint data. It was confirmed that fuzzy clustering method is effective and valid for joint set identification and estimation of mean direction and degree of clustering of huge joint data through the applications.

• Tunnel and Underground Space
• /
• v.19 no.1
• /
• pp.31-42
• /
• 2009

One set of hardware system of guide point method (GP method), modified from the multistage convergent photographing technique, was developed to interpret the geometrical characteristics of Joints photogrammetrically on rock slope. Before the field application of the hardware system, the level of errors and constraints that ran be acceptable in the field measurement has been severely investigated in the laboratory and the optimum photographing scheme was analyzed. The range of the most suitable convergence angle between two cameras was $25^{\circ}{\sim}150^{\circ}$ and the photographing distance was about 5.5 m when using a 2 M pixel digital camera. An extended analyzing technique, which was newly developed in this study, was applied to the field measurement to magnify the benefits of GP method. This technique can be applied when survey for the wide range of rock surface is necessary. The global coordinates of ground control points for the neighbor photographing area ran be introduced without any preparation from the previous photographed area using this technique. It could reduce phographing time in the field.

• Tunnel and Underground Space
• /
• v.22 no.1
• /
• pp.43-53
• /
• 2012

Stability of cut-slope, the orientation and dimension of which are gradually changed, has been analyzed by employing the cross-section method capable of comprehensibly considering the lithological, structural and mechanical characteristics of slope rock. Lithological fragility is investigated by inspecting the drilled core logs and BIPS image has been taken to delineate the rock structure. Engineering properties of drilled-core including the joint shear strength have been also measured. Potential failure modes of cut-slope and failure-induced joints are identified by performing the stereographic projection analysis. Traces of potential failure-induced joints are drawn on the cross-section which depicts the excavated geometry of cut-slope. Considering the distribution of potential plane failure-induced joint traces blocks of plane failure mode are hypothetically formed. The stabilities and required reinforcements of plane failure blocks located at the different excavation depth have been calculated to confirm the applicability of the cross-section method for the optimum cut-slope design.

• Journal of the Korean Geotechnical Society
• /
• v.18 no.4
• /
• pp.119-126
• /
• 2002

A reliability analysis is performed to investigate the influence of the uncertainty from few in-situ samples and inherent heterogeneity of the ground on the probability of failure for a rock cut slope. The results are compared with those of deterministic slope stability analysis. The random variables used are unit weight of the rock, the angle of potential slope of failure, and cohesion and internal friction angle of joints. It was found that the rock slope in which the factor of safety satisfied the minimum safety factor in the deterministic analysis has high probability of failure in the reliability analysis when the weak geological strata are involved in the cut slope. The probability of failure of rock slope is most sensitive to the mean and standard deviation of cohesion in rock joint among the random soil parameters included in the reliability analysis. Sensitivities of the mean values are larger than those of standard deviations, which means that accurate estimation of the mean for the in-situ geotechnical properties is important.

• Tunnel and Underground Space
• /
• v.16 no.5 s.64
• /
• pp.368-376
• /
• 2006

After heavy rainfall, It was occurred massive plane failure along bedding plane of shale in the center of rock slope. It was observed filling material and trace of underground water leakage around of the slope. We tried to find the cause for slope failure, and the result of examination showed that primary factors of the failure were low shear strength of clay filling material and water pressure formed within tension crack existed in the top of the slope. In this research, in order to examine the features of shear strength of filled rock joint, shear test of filled rock joint was conducted using of artificial filling material such as sand and clay..Also we made an investigation into the characteristics of shear strength with different thickness of filling materials.

• The Journal of Engineering Geology
• /
• v.24 no.4
• /
• pp.473-486
• /
• 2014

The objective of this study is to produce the rock slope hazard map on the Mt. Hwangryeong located at center of Busan Metropolitan City for evaluating the rock slope hazard susceptibility. The Mt. Hwangryoeng is located between Dongrae and Ilkwang faults and consists of various rocks such as sedimentary rock, andesitic volcanic rock, andesite, gabbro and granitic rocks. Thematic maps were carried out using ArcGIS for Database including the orientations and density of joints, strength of rock constructed through the field survey and results from previous studies. Also, rock slope hazard susceptibility for the Mt. Hwangryoeng area was studied using empirical method through checklists proposed by NDMI (National Disaster Management Institute). Results from using the empirical method indicated that rock slopes are evaluated from very stable to stable, but moderate stability has been partially presented along the edge of the mountain area.

• Tunnel and Underground Space
• /
• v.11 no.3
• /
• pp.279-288
• /
• 2001

Jointed rock mass can be analyzed by either continuum model or discontinuum model. Finite element method or finite difference method is mainly used for continuum modelling. Although discontinuum model is very attractive in analyzing the behavior of each block in jointed blocky rock masses, it has shortcomings such that it is difficult to investigate each joint exactly with the present technology and the amount of calculation in computer becomes trio excessive. Moreover, in case of the jointed blocky rock mass which has more than 2 dominant joint sets, it is impossible to model the behavior of each block. Therefore, a model such as ubiquitous joint model theory which assumes the rock mass as a continuum, is required. In the case of tunnels, unlike slopes, it is not easy to obtain safety factor by utilizing analysis method based on limit equilibrium method because it is difficult to assume the shape of failure surface in advance. For this reason, numerical analyses for tunnels have been limited to analyzing stability rather than in calculating the safety factor. In this study, the behavior of a tunnel excavated in jointed rock mass is analyzed numerically by using ubiquitous joint model which can incorporate 2 joint sets and a method to calculate safety factor of the tunnel numerically is presented. To this end, stress reduction technique is adopted.

• The Journal of Engineering Geology
• /
• v.21 no.1
• /
• pp.1-13
• /
• 2011

Joint roughness is one of the most important parameters in analysis of rock slope stability. Especially in probabilistic analysis, the random properties of joint roughness influence the probability of slope failure. Therefore, a large dataset on joint roughness is required for the probabilistic analysis but the traditional direct measurement of roughness in the field has some limitations. Terrestrial LiDAR has advantagess over traditional direct measurement in terms of cost and time. JRC (Joint Roughness Coefficient) was calculated from statistical parameters which are known from quantitative methods of converting the roughness of the material surface into JRC. The mean, standard deviation and distribution function of JRC were obtained, and we found that LiDAR is useful in obtaining large dataset for random variables.