• Resources Recycling
• /
• v.9 no.4
• /
• pp.50-55
• /
• 2000

Recycling technology of aluminum foil scraps into aluminum flake powder by ball milling in dry or wet conditions was studied. Aluminum foil were laminated each other, elongated through microforging by the falling balls, fragmented into small foils and then changed into flake powder during ball milling. It is also possible to recycle foil scraps with thickness less than $60\mu\textrm{m}$ into aluminum paste by wet ball milling. As initial foil thickness decreases, foil is easily milled to flake powder by wet milling in mineral spirits. the appearance and the opaque character of glass painted with aluminum paste obtained by wet milling of foils are similar to those of aluminum paste made by ball milling of gas atomized powder.

• Resources Recycling
• /
• v.28 no.2
• /
• pp.3-13
• /
• 2019

Aluminum is the most abundant metal and the second most plentiful metallic element in the earth's crust, after silicon. Aluminum is a light, conductive, and corrosion resistant metal with strong affinity for oxygen. However, the primary aluminum production process is highly energy intensive. The recycling of aluminum scrap reduces the energy consumption and environmental burden, comparing to the primary metal production. However, the amount of the recovered metal from scrap is limited because of the difficulties to remove the impurities in the scrap. This work provides an overview of the aluminum production and recycling process, from the preparation of alumina to the scrap upgrading and the melting process.

• Resources Recycling
• /
• v.29 no.1
• /
• pp.70-80
• /
• 2020

This study investigates the effect of flux type and mixing ratio on efficiency in aluminum can scrap recycling using induction furnace. The removal of surface coating layer of aluminum can scrap was possible through heat treatment at about 500 ℃ for about 30 min. The temperature for the melting process was set to be slightly above the melting temperature of the aluminium can scrap. The molten metal treatment was performed with different types of flux and mixing ratio. As a result, The optimum efficiency of Al recovery ratio was revealed when the process was performed with at least 3 wt.% of the flux (Salt and MgCl₂ mixture of ratio 70:30) at 750 ℃. The mechanical property of the recovered Al alloy showed that the tensile strength is about 249 MPa and elongation is about 14 %. This result was found to be similar to the mechanical property of the virgin Al 5083 alloy.

• Electrical & Electronic Materials
• /
• v.9 no.8
• /
• pp.806-812
• /
• 1996

I-V characteristics of ground electrode fabricated using an aluminium scrap are presented. We fabricated several shapes of aluminium scraps and aluminium electrodes. The results show that the current of aluminium electrode increased linearly by the voltage increase. AC breakdown voltage of copper plate electrode was higher than that of aluminium electrode. AC breakdown current of aluminium electrode was higher than that of copper plate electrode. As applied voltage increased, grounding resistance of aluminum electrode decreased linearly.

• Resources Recycling
• /
• v.24 no.5
• /
• pp.72-79
• /
• 2015

Since there are many kinds of non-ferrous metal, it is difficult to investigate the current status on the recycling of all the non-ferrous metals. Therefore, the survey is confined to some commercially important non-ferrous metals such as copper, aluminum, zinc, lead, nickel and magnesium in this article. Domestic demand and production of these non-ferrous metals in recent years (2010-2014) and recycling ratio of the scraps are estimated briefly here.

• Resources Recycling
• /
• v.22 no.6
• /
• pp.81-86
• /
• 2013

Since there are many kinds of non-ferrous metal, it is difficult to investigate the current status on the recycling of all the non-ferrous metals. Therefore, the survey is confined to some commercially important non-ferrous metals such as copper, aluminum, zinc, lead, nickel and magnesium in this article. Domestic demand and production of these non-ferrous metals in recent years(2010-2012) and recycling ratio of the scraps are estimated briefly here.

• Resources Recycling
• /
• v.29 no.5
• /
• pp.3-14
• /
• 2020

Magnesium is the third most abundant structural metal after aluminum and iron. Magnesium is the lightest metal in the common metals. It has a density 33 % less than aluminum and 77% lower than steel. However, the primary magnesium production process is highly energy intensive. The recycling of magnesium scrap reduces the energy consumption and environmental burden, comparing to the primary metal production. However, the amount of recovered metal from scrap is limited because of the difficulties to remove the impurities in the scrap. This work provides an overview of the magnesium production and recycling process.

• Resources Recycling
• /
• v.30 no.1
• /
• pp.26-34
• /
• 2021

Titanium is the fourth most abundant structural metal, after aluminum, iron, and magnesium. However, it is classified as a 'rare metals', because it is difficult to smelt. In particular, the primary titanium production process is highly energy-intensive. Recycling titanium scraps to produce ingots can reduce energy consumption and CO2 emissions by approximately 95 %. However, the amount of metal recycled from scrap remains limited of the difficulty in removing impurities such as iron and oxygen from the scrap. Generally, high-grade titanium and its alloy scraps are recycled by dilution with a virgin titanium sponge during the remelting process. Low-grade titanium scrap is recycled to ferrotitanium (cascade recycling). This paper provides an overview of titanium production and recycling processes.

• Proceedings of the Korean Institute of Resources Recycling Conference
• /
• 1993.03a
• /
• pp.6.1-6
• /
• 1993

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 1998.04b
• /
• pp.17-17
• /
• 1998