• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.8
• /
• pp.94-102
• /
• 2013

We propose the mirror active element pattern (AEP) method for the radiation pattern computation of linear array antennas versus scan angles. The computation time for the radiation pattern of linear array antennas using the mirror AEP method is reduced by almost half compared to that using the AEP method because the number of AEPs of elements obtained by the full-wave simulation necessary for the radiation pattern computation of linear array antennas is reduced by almost half. The difference between the radiation patterns of linear array antennas obtained by the full-wave simulation and mirror AEP method is very small for wide scan angle range when the radiation pattern of an antenna element is symmetric.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2008.05a
• /
• pp.1789-1793
• /
• 2008

전자파표면유속계는 홍수유속측정을 위하여 개발된 기기로 평 갈수기에는 유속측정이 불가하여 프로펠러 유속계를 이용하고 있다. 현재 보급된 전자파표면유속계는 하천의 흐름방향에 나란하게 설치하였을 때에만 유속을 측정할 수 있는 기기의 구조상의 한계성 때문에 교량이 없는 지점에서는 유속측정이 불가하여 유량산정을 할 수가 없다. 또한 편각측정이 불가능하여 기기를 각 측선마다 이동 설치하여야 하기 때문에 유속측정시 효율성 떨어진다. 이에 홍수시 유량측정의 효율성을 증대시키고 전자파표면유속계의 활용도를 높이고자 편각측정이 가능하도록 전자파표면유속계의 성능을 개선하는 것이 본 연구의 주된 목적이다. 전자파표면 유속계에서의 편각 측정은 하천의 유속방향을 기준으로 정면에서 측정하면 수평 편각이 0도가 되며 좌우로 안테나를 회전하여 움직인 각도가 측정 편각으로 결정된다. 현장에서 전자파표면유속계의 사용시 편의성을 높이고 유량측정을 효율적으로 하기 위해서는 가급적 편각을 크게 해서 측정을 해야 하지만, 편각이 증가하면 전자파의 물리적 특성 때문에 반사된 신호의 수신 크기가 감소하여 측정이 불가능하게 된다. 이러한 문제를 해결하기 위해서는 유속 측정시 전자파 출력을 기존의 시스템보다 높게 물표면에 발사하여야 하며 안테나를 포함한 RF 모듈의 수신감도 및 지향성이 개선되어야 한다. 이에 편각측정이 가능하도록 이러한 사항에 주안점을 두어 새로운 시스템을 구성하였다. 수신감도 향상을 위해서는 물표면에 반사되어 돌아오는 신호를 가장 먼저 수신하는 안테나의 특성이 중요하며 그 다음 수신용 증폭기, IF 증폭기 순으로 개선이 필요하다. 본 연구에서는 안테나의 형태를 기존 파라볼릭 안테나에서 위상 배열 평면안테나로 변경하였으며, 이에 따른 이점으로는 송수신부를 분리하여 하나의 평면에 두 개의 안테나를 구성할 수 있다는 사항이다. 즉 외형적으로는 하나의 안테나로 보이지만 두 개의 안테나가 하나로 구성된 것이다. 송수신부를 분리하는 형태는 기존 파라볼릭 안테나에선 불가능한 구조로 변경에 따른 수신감도 향상은 수치적으로 10dB 이상 개선하였다. 송수신부 분리가 수신감도에 영향을 미치는 이유는 물표면으로 발사된 송신 신호의 일부가 수신단으로 유입되는 현상으로 누설되는 송신 신호를 최대한 차단하는 분리도가 수신 신호 검출에 직접적인 양향을 주기 때문에다. 평면 안테나를 적용하면 기존 파라볼릭 안테나에서 사용하던 써큘레이터라는 부품을 삭제할 수 있으며, 안테나의 구조적인 분리를 통해서 수신감도를 개선할 수 있었다. 안테나의 지향성은 발사하는 전자파의 빔폭 성능과 일치하며 각도 단위로 표시한다. 각도 값이 작을수록 전자파의 에너지가 한 곳에 집중된다고 말할 수 있다. 즉 빔폭이 크면 측정시 반사면적이 커져 정확한 지점의 유속을 측정하기 어려운 문제가 발생한다. 본 연구를 통해 빔폭은 기존 안테나 대비2도를 개선하였으며 25%의 개선 효과를 얻었다. 또한 수신감도 및 지향성 개선과 더불어 전자파의 출력을 기존 장비 대비하여 1.6배를 증가하여 편각측정을 위한 전자파표면 유속계의 성능을 개선하였다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.40 no.12
• /
• pp.1086-1092
• /
• 2012

It has been studied for DGPS/INS(Differential Global Positioning System/Inertial Navigation System) to offer the more precise and reliable navigation data with the aviation industry development. The flight performance evaluation of navigation system is very significant because the reliability of navigation data directly affect the safety of aircraft. Especially, the high-level navigation system, as DGPS/INS, need more precise flight performance evaluation method. The performance analysis is performed by comparing between the DGPS/INS navigation data and reference trajectory which is more precise than DGPS/INS. The GPS receiver, which is capable of post-processed CDGPS(Carrier-phase DGPS) method, can be used as reference system. Generally, the DGPS/INS is estimated the CG(Center of Gravity) point of aircraft while the reference system is output the position of GPS antenna which is mounted on the outside of aircraft. For this reason, estimated error between DGPS/INS and reference system will include the error due to lever arm. In order to more precise performance evaluation, it is needed to compensate the lever arm. This paper presents procedure and result of flight test which includes lever arm compensation in order to verify reliability and performance of DGPS/INS more precisely.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.7
• /
• pp.784-795
• /
• 2007

In this thesis, the Multi element antenna with wideband and enhanced gain characteristic is proposed to operate at both frequency range from 824 MHz to 896 11Hz for the CDMA and frequency range from 908.5 MHz to 914 MHz for the RFID band. The proposed antenna has tile size of $35{\times}15{\times}5mm^3$ in order to put it in the A model of S company and each element of the proposed antenna is folded to obtain the minimum size. To obtain the antenna with wideband and high gain characteristic, the radiator of the antenna is divided into 4 elements. As a result, bandwidth of the proposed antenna become broader and lower center frequency is appeared due to increased and lengthened current path. Moreover, the enhanced gain characteristic is verified because divided element structure that induct uniform current distribution can get increased antenna efficiency. To attain more uniform current distribution, modified structure of the feeding point that can deliver currents directly is designed. The antenna that alters the feeding structure has higher gain value. Each element is folded to increase the current paths considering the current directions to attain the miniaturization of the antenna. To measure the handset antenna, the handset case must be considered. Even though antenna is designed for predicted characteristic, the resonance frequency is shifted and antenna gain is deteriorated at predicted frequency while antenna is set in the handset case. 1.08 GHz of the resonant frequency is determined after frequency shift from 150 MHz to 200 MHz is confirmed and the maximum gain is measured as 3.1 dBi while antenna is not set in the handset. In case handset case is considered, the experimental results show that the impedance bandwidth for VSWR<2 is from 0.824 GHz to 0.936 GHz(110 MHz). This result appears that the proposed antenna can cover both CDMA and RFID band at once. The measured gain is from -3.4 dBi to -0.5 dBi and it has omni-directional pattern practically.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.9
• /
• pp.1015-1022
• /
• 2007

In this paper, we proposed a wideband design of planar inverted-F antenna(PIFA) using two-layer, patches and modified ground structure. The antenna consists of two layer patches with common feed and modified ground plane to control resonance frequency and antenna input impedance. The measured bandwidth is 1,492 MHz(BW: 67.7 %, 1,457${\sim}2,949$ MHz) for VSWR<2, and 1,170 MHz(BW: 21 %, 4,970${\sim}$6,140 MHz) for VSWR<2.5. It covers service bands of DCS1800, DCS1900, UMTS(WCDMA), WiBro, WLAN(IEEE 802.11b), satellite DMB. WLAN(IEEE 802.11a) in Korea and radiation patterns shows constant figure with frequency change.

• Proceedings of the Korean Association of Geographic Inforamtion Studies Conference
• /
• 2008.06a
• /
• pp.254-259
• /
• 2008

지형의 표고값물 격자간격으로 표현하는 수치표고모델(DEM)은 지형분석을 위한 GIS데이터 활용과 휴대전화 중계안테나의 영향권 분석, 정밀지오이드 계산을 위한 지형효과계산 등 여러 가지 분야에 활용되고 있다. 본 연구에서는 이렇게 활용성이 증가하고 있는 수치표고모델을 수집하고 또 진주시 지역을 대상으로 LiDAR촬영을 통한 LiDAR 수치표고모델을 구축하여 그 정확도를 분석하고자 하였다. 연구에 활용된 수치표고모델은 GTOPO30, SRTM-3, 지형도(1/50,000) 독취 DEM, 환경부 DEM, 항공사진에 의해 생성된 DEM, 그리고 LiDAR DEM의 6가지이며, 정확도 분석을 위해 GPS측량과 수준측량이 동시에 실시된 409점의 진주시 3차원 도시기준점 성과를 이용하였다.

• Proceedings of the Korean Society of Surveying, Geodesy, Photogrammetry, and Cartography Conference
• /
• 2010.04a
• /
• pp.201-206
• /
• 2010

A project for construction of Korea Geodetic VLBI has officially started in Oct. 2008. The construction of all system will be completed by the end of 2011. The project was named Korea VLBI system for Geodesy (KVG), and its main purpose is to maintain the Korea Geodetic Datum. In case of the KVG system, an observation room where an H-maser frequency standard is located is in a building separated from an antenna by several tens of meters. Therefore KVG system will adopt a so-called round-trip system to transmit reference signals to the antenna with diminishing the effect of path length variations. KVG's round-trip system is designed not only available to use either metal or optical fiber cables, but also available to measure path length variations directly by using K5/VSSP32 sampler. We will present principle of round-trip system and the new type of round trip system for KVG.

• Journal of IKEEE
• /
• v.26 no.2
• /
• pp.211-218
• /
• 2022

This paper presents a S-band phased array antenna system for receiving LEO satellite telemetry signals. The proposed antenna, which is performed to be beam-tiled along the elevation direction, consists of 16 sub-array assemblies, 16 active circuit modules, a perpendicular feed network and a control/power unit. In order to precisely track an LEO satellite, the developed antenna is placed with its elevation axis along the projected trajectory of the satellite on the earth. The center of antenna aperture is facing to the maximum elevation angle in the LEO trajectory. The beam-tilted angles for tracking LEO satellite are obtained by calculating accurately satellite points. Satellite tracking measurements are carried out in the range of ±30° with the respect to the maximum elevation angle. The S/N ratio of 16.5 dB and the Eb/No of 13.3 dB at the maximum elevation angle are obtained from the measurements. The measured result agrees well with the pre-analyzed system margin.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.7
• /
• pp.3-8
• /
• 2014

We consider a limited feedback based hybrid beamforming which reduces the energy of feedback information. In the millimeter wave channel, some rays with large ray gain dominate energy of the channel. Using this point, we propose a channel feedback scheme that employs limited number of channel rays. Also, we provide a hybrid beamforming scheme for the limited feedback system. Based on the simulation results, the proposed scheme shows a comparable data rate performance with conventional schemes, while it remarkably reduces energy of channel feedback.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.18 no.6
• /
• pp.1015-1022
• /
• 2023

In this paper, we propose DLP(Dual Linear Polarization) antenna with aperture coupled feeding structure for private network. The proposed antenna has general aperture coupled structure and design two port between top and bottom layer to obtain the enhanced isolation. Also, The size of each substrate(top and bottom layer) is 34.0 mm(W)×34.0 mm(L), which is designed on the FR-4 substrate which thickness (h) is 1.0 mm, and the dielectric constant is 4.4. Also, the size of patch antenna is 12.70 mm(W2)×14.60 mm(L3), and it is located on the top layer. The size of feeding line is 24.0 mm(W2)×1.6 mm(L3), and is located at the bottom layer Also, rectangular slot is located on the ground plane between top layer and bottom layer. From the fabrication and measurement results, bandwidths of 300 MHz (4.52 to 4.82 GHz) for feeding port 1, and 170 MHz (4.65 to 4.82 GHz) for feeding port 2 are obtained on the basis of -10 dB return loss and transmission coefficient S21 is got under the -30 dB. Also, cross polarization isolation between each feeding port obtained