• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.9 s.112
• /
• pp.829-835
• /
• 2006

In this paper, new structure of the Cassegrain reflector antenna whose spill-over is efficiently reduced by modified reflectors is proposed for high power. It can be achieved by designing the geometry of subreflector in Cassegrain system using two hyperbolic curves in order to be suitable a lager beamwidth of feeding pattern without broadening main reflector. Finally, radiation efficiency and side lobe level of the proposed Cassegrain reflector antenna can be improved respectively 9 %, 10 dB than conventional one.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.6 no.1
• /
• pp.18-22
• /
• 2013

Input impedance of the inverted L antenna which is modified from a monopole antenna varies to very high input impedance value when the ratio of vertical height to horizontal length is reduced. So its impedance matching becomes very difficult. In this paper, we analyzed the input impedance variation range depending on the ratio of vertical height to horizontal length in the normal and ferrite thin film added configuration for the input impedance control. For the exact analysis involving the permittivity, permeability and conductivity of ferrite material, FDTD numerical method is used.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.11 no.6
• /
• pp.135-141
• /
• 2008

In this paper, a design method of broadband horn antenna having 3:1 bandwidth and multiple polarization characteristics is proposed. The feeding section of the antenna adopts quadruple-ridged waveguide type for broadband and multiple polarization characteristics of the antenna. By inserting a shorting bar in the cavity structure with a semi-sphere type back short, the return loss at the feeding section was minimized. A corrugated dielectric lens is designed for phase compensation and lens-surface matching at the antenna aperture, which improves the antenna beam pattern. The validity of the design method is verified by indicating the measured data of the antenna.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.26 no.12B
• /
• pp.1724-1732
• /
• 2001

In this paper, a technique for increasing the bandwidth of microstrip array antennas using the parallel coupled lines on a single layer is presented. Four types of wideband microstrip array antenna are designed and the characteristics of each type are analyzed. In addition, an iterative method using a distributed network is proposed to design the parallel coupled lines as a wideband impedance matching network. Measurements show that the proposed antennas provide wider bandwidths ∼1.7 times those of conventional microstirp array antennas, while the sizes of proposed antennal are the same as that of a conventional array. And low cross-polarization level can be obtained through symmetrical locations of the parallel coupled lines section

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.27 no.7B
• /
• pp.727-736
• /
• 2002

In this paper, the broadband microstrip antenna with small size, thin-profile, conformability and ease of manufacture is proposed for providing PCS(down link: 1.75GHz∼1.78GHz, up link: 1.84GHz∼1.87GHz) '||'&'||' IMT-2000(down link: 1.92GHz∼1.98GHz, up link: 2.11GHz∼2.17GHz) services simultaneously. By using double U-slots and matching stub, the bandwidth and operating performance of printed antenna was significantly improved, with need for a complex fabrication procedure. We have also studied the various parameters of the U-slot$_2$for the performances of the antenna. Impedance bandwidth of the wideband microstrip antenna with the double U-slots is about 30.45% (VSWR<2)

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.2
• /
• pp.194-198
• /
• 2004

This paper presents a broadband compact microstrip antenna design with four U slots on the ground plane by using of genetic algorithm. FDTD method is used as fitness function for antenna analysis, and length of rectangular patch, length of ground plane slot, distance from center point to feed point is used as optimization parameter for maximum bandwidth and minimum size. The measurement result of implemented antenna present 10 dB bandwidth of 15.63 ％ and peak gain of 3.61 dBi in the 2.445 GHz, and antenna has a reduced patch size of 54.8 ％ compare with normal microstrip antenna.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.18 no.4
• /
• pp.49-53
• /
• 2018

Parabolic offset antenna is widely used for wireless communication system. The general structure of parabolic offset antenna system is composed of supporting stand and RF devices under parabolic reflector. However sidelobe distortion in gain pattern is occurred by supporting stand and RF devices. Depending on position of subsidiary devices, angle of sidelobe distortion can be changed. In this paper we describe method for sidelobe distortion suppression using raytracing. We calculate 3D vector for sidelobe distortion suppression zone by raytracing method and compare when subsidiary device is in sidelobe distortion suppression zone or not. By comparison, we show method for parabolic antenna sidelobe distortion suppression.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.36D no.2
• /
• pp.31-40
• /
• 1999

Characteristics of monopole antenna and planar conductor structure mounted on handheld telephone are anlayzed by using FDTD method. Feeding of monopole antenna is implemented with lumped elements and plastic case is coated on the surface of conductor box. Otherwise, resonant frequency of handheld telephone mounting monopole antenna with no plastic case is 877MHz, when plastic case (${\varepsilon}_r=2$) is coated, the resonant frequency is down to 82MHz and the bandwidth is broadened about 1.5 times. Planar structure of handheld telephone mounted on the body makes to change far-field gain radiation patterns. In this case, radiation patterns are somewhat asymmetrical. Handheld telephone using PIFA(Planar Inverted F Antenna), instead of monopole antenna, is resonated at frequency 1.52GHz that is available onPCS. In the radiation pattern of this structure, azimuth that electric field intensity is presented below 20dB is 14$^{\circ}$.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.9
• /
• pp.978-984
• /
• 2008

In this paper, we propose a RFID metal tag antenna with a minimum by size of a metal surface to attach. This proposed tag antenna is a patch antenna which is able to stick on metal surface and designed for very slim structure ($119{\times}30{\times}1.6$ mm) antenna that is matched to a chip impedance. This has a loop coupling feeding and consists of a inner radiator and a outer radiator. The outer radiator activates the current to concentrate on the inner radiator regardless of metal size to attach. Also the tag antenna is designed by CST microwave tool and the performance is measured in the anechoic chamber. The optimum antenna has 3.77 % of the matching bandwidth($S_{11}<-10$ dB). The readable range of the tag antenna is about 2.9 m on metal(max. size $700{\times}700$ mm) and 5.5 m in free space according to the measurement results.

• Journal of Advanced Navigation Technology
• /
• v.16 no.5
• /
• pp.766-772
• /
• 2012

In the present study, wideband microstrip monopole slot antennas which can be applied to the RF4CE Zigbee remote controller are designed. First I-shaped monopole slot antenna which has ${\lambda}g/4$ length at 2.45GHz is designed. In particular, a conducting via is used to connect the microstrip feed line and the ground plane surrounded with the etched slot for the bandwidth improvement. In order to reduce the antenna size, it is changed into L-shaped and T-shaped monopole slot antennas for which improve results of antenna performance are observed. In case of T-shaped monopole slot antenna, impedance bandwidth(VSWR<2) is about 3.32GHz, and also its radiation efficiency and gain is more than 90% and 2.1dBi respectively at whole operating frequency range. In particular, all of proposed monopole slot antennas have the end-fire radiations which has a maximum radiation power toward direction of open ends of monopole slots.