• Applied Chemistry for Engineering
• /
• v.23 no.1
• /
• pp.18-22
• /
• 2012

Photocurable binder for a transparent glass fiber composite was prepared with alicyclic methacrylate and fluorene-based diacrylate. ANOVA (analysis of variance) analysis was used to know main factors affecting the conversion of photocurable binder. It showed radiation intensity and photoinitiator (PI) concentration were main factors. The conversion of photocurable binder was simply increased with radiation intensity. Its increment however was abated with increasing PI concentration. We found that average conversion of the binder measured by FTIR-ATR was 87% when it was exposed to $5J/cm^2$ of UV dose with 5 wt% of PI. Oxime ester type PI was very effective to get a high degree of conversion, but it caused a yellowing problem. Owing to post-baking process, UV cured film showed an improved thermal stability by increase of conversion and removal of volatile organic compounds. TG% at $260^{\circ}C$ of film cured with 5 wt% of PI (TPO+MBF) and $5J/cm^2$ of UV radiation increased from 95.4 to 99.0% by post-baking at $230^{\circ}C$ for 5 min.

• Conservation Science in Museum
• /
• v.15
• /
• pp.56-65
• /
• 2014

The face of the Seated Stone Buddha ^{Korean Treasure No.84} of Sinboksa Templesite in Gangneung was contaminated with a glossy resin, spoiling its beauty. The contaminants covered the face, the forehead of the urna, to the bottom of the jaw. FT-IR analysis on a sample of the contaminants identified the substance as cyanoacrylate instant adhesive, which can normally be melted with acetone and removed with a swab. However, given that the surface of the statue was severely weathered from prolonged open-air exposure, alternative removal procedures were considered, to minimize the possibility of physical damage. After research, two removal procedures were utilized: one procedure involving poultices, which had been used to remove graffiti from the Samjeondobi Stele, and one procedure involving steam sterilization, which has been used to remove resin from pottery and porcelain. When both the poultices and steam sterilization were applied together, the resin was removed within twenty-four hours, without physical work using a swab.

• The Korean Journal of Rheology
• /
• v.9 no.4
• /
• pp.151-162
• /
• 1997

다층 구조를 갖는 고무/아크릴 충격보강제가 poly(methyl methacrylate) (PMMA)/ 충격보강제 블렌드의 몰폴로지와 유변학적 성질에 미치는 영향을 고찰하였다. TEM으로 측 정한 블렌드 내의 충격보강제 몰폴로지는 그 함량에 관계없이 균일한 크기의 구형을 이루는 것으로 나타났으며 파괴 단면의 SEM 측정으로부터 충격보강제와 매트릭스 수지와의 강한 결합력을 확인할수있었다. 블렌드의 유변물성 측정 실험에서는 충격보강제 함량이 복합 점 도에 크게 영향을 준 반면, capillary rheometer로부터 얻은 정상상태 점도에는 별 영향을 주지않음이 확인되었다. 특히 동적응력 실험의 고진동 주파수 영역에서는 일정 충격보강제 함량이상 일 때 충격보강제 자체의 점도와 근사해졌으며 이와같은 현상을 충격보강제의 shell 분자 상호간 또는 매트릭스 분자와의 엉킴에서 비롯되는 물리적인 상호 작용측면에서 설명해보았다. 또한 실험 결과를 Palierne[16]의 비상용성 블렌드계의 이멀젼 모델과 비교한 결과 상당한 차이를 확인할수 있었으며 이러한 차이는 위에서 언급한 shell 분자 상호간 또 는 매트릭스 분자와의 엉킴에 기인한다고 추정된다.

• Korean Journal of Heritage: History & Science
• /
• v.55 no.2
• /
• pp.200-211
• /
• 2022

The celadon stools with an openwork ring design which consist of four items as one collection were excavated from Gaeseong, Gyeonggi-do Province. The celadon stools were designated and managed as treasures due to their high arthistorical value in the form of demonstrating the excellence of celadon manufacturing techniques and the fanciful lifestyles during the Goryeo Dynasty. However, one of the items, which appeared to have been repaired and restored in the past, suffered a decline in aesthetic value due to the aging of the treatment materials and the lack of skill on the part of the conservator, raising the need for re-treatment as a result of structural instability. An examination of the conservation condition prior to conservation treatment found structural vulnerabilities because physical damage had been artificially inflicted throughout the area that was rendered defective at the time of manufacturing. The bonded surfaces for the cracked areas and detached fragments did not fit, and these areas and fragments had deteriorated because the adhesive trickled down onto the celadon surface or secondary contaminants, such as dust, were on the adhesive surface. The study identified the position, scope, and conditions of the bonded areas at the cracks UV rays and microscopy in order to investigate the condition of repair and restoration. By conducting Fourier-transform infrared spectroscopy(FT-IR) and portable x-ray fluorescence spectroscopy on the materials used for the former conservation treatment, the study confirmed the use of cellulose resins and epoxy resins as adhesives. Furthermore, the analysis revealed the addition of gypsum(CaSO₄·2H₂O) and bone meal(Ca₁₀ (PO₄)₆(OH)₂) to the adhesive to increase the bonding strength of some of the bonded areas that sustained force. Based on the results of the investigation, the conservation treatment for the artifact would focus on completely dismantling the existing bonded areas and then consolidating vulnerable areas through bonding and restoration. After removing and dismantling the prior adhesive used, the celadon stool was separated into 6 large fragments including the top and bottom, the curved legs, and some of the ring design. After dismantling, the remaining adhesive and contaminants were chemically and physically removed, and a steam cleaner was used to clean the fractured surfaces to increase the bonding efficacy of the re-bonding. The bonding of the artifact involved applying the adhesive differently depending on the bonding area and size. The cyanoacrylate resin Loctite 401 was used on the bonding area that held the positions of the fragments, while the acrylic resin Paraloid B-72 20%(in xylene) was treated on cross sections for reversibility in the areas that provided structural stability before bonding the fragments using the epoxy resin Epo-tek 301-2. For areas that would sustain force, as in the top and bottom, kaolin was added to Epo-tek 301-2 in order to reinforce the bonding strength. For the missing parts of the ring design where a continuous pattern could be assumed, a frame was made using SN-sheets, and the ring design was then modeled and restored by connecting the damaged cross section with Wood epos. Other restoration areas that occurred during bonding were treated by being filled with Wood epos for aesthetic and structural stabilization. Restored and filled areas were color-matched to avoid the feeling of disharmony from differences of texture in case of exhibitions in the future. The investigation and treatment process involving a variety of scientific technology was systematically documented so as to be utilized as basic data for the conservation and maintenance.

• Polymer(Korea)
• /
• v.38 no.6
• /
• pp.760-766
• /
• 2014

Bead type super-absorbent resins to be used for release-control were prepared by modification of the inverse suspension polymerization, and their physical properties were characterized. Acrylic acid and acrylamide were used as monomers, and N,N-methylenebisacrylamide was used as crosslinker, controlling the viscosity of monomer solution by adding hydroxyethylcellulose (HEC). SEM studies of the synthesized beads verified that the bead surfaces had many pores with their diameters of several tens nm. The bead sizes were in the range of $500{\sim}3000{\mu}m$, depending on the viscosity of the monomer solution. Both absorbent amount and absorbent rate of the beads were inversely proportional to the bead size, and the maximum water absorbent amount of 1 g beads was determined to be ca. 170~200 g for 5 hrs. The absorbent rate was also dependent on pH change of the aqueous solution, exhibiting the maximum rate in pH ranging from 5 to 11. The absorbent rate decreased as the concentration of salt (NaCl and $MgCl_2$) or ethanol and ethylene glycol increased. Release time of the water absorbed into the bead resins was 700 hrs, confirming the usefulness of the resin for the good release-control materials.

• Clean Technology
• /
• v.11 no.1
• /
• pp.41-50
• /
• 2005

In this study, semibatch emulsion copolymerization of n-BA as adhesive component and MMA as coagulant component were carried out for the stable acrylic polymer latex in aqueous phase for polymer cement using LE-type nonionic surfactant as environmental friendly surfactant. The stable polymer emulsion was obtained with the increases of chain length(n) of this surfactant. The effect on the amount of LE-50 as nonionic surfactant were showed that the concentration of polymer latex were increased by increasing the amount of LE-50, whereas the average particle size were decreased by increasing the amount. The addition of functional monomer in initial reactor charge showed a significant effect on the final polymer concentration and the latex particle size. The single polymerization of each n-BA or MMA showed a very low concentration of polymer latex and very big particle size due to coagulation. In the polymerization composed of mixed monomer with MMA and n-BA, the larger the ratio of MMA to n-BA in the copolymers, the greater the amount of coagulum produced. It was found that a stable copolymers were obtained in the range of 15-35 % of n-BA. Moreover, incorporation of some functional monomers in addition to of main monomers became more stable polymer latex. Through DSC and IR analysis, the final polymer latex was composed by MMA/n-BA/AA/AM with a single Tg depending on the reaction conditions. As a result, the conditions of this acrylic polymerization could also be effectively controlled to get the desired final products.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.14 no.1
• /
• pp.79-91
• /
• 2012

A curved fiber reinforced polymer (FRP) panel is produced with a certain width depending on allowances of manufacturing processes and facilities. An targeted arch-shaped structure could be built by sequential connection of series of the FRP panels. The connection manner between the FRP panels could be given by chemical treatment, mechanical treatment and hybrid method. Among those, the connection between the panels by chemical treatment is commonly adopted. Therefore, For an optimized design of the connected part between FRP pannels, a number of direct shear tests have been undertaken in terms of a number of parameters: surface treatment conditions, bonding materials, etc.. As results, surface grinding condition by sand paper or surface treatment by sand blasting appear properly acceptable methods, and epoxy and acryl resins are shown to be effective bonding materials for the purpose in this study.

• 보존과학연구
• /
• s.29
• /
• pp.65-90
• /
• 2008

This study examines the status and the physical features of Paraloid B-72 layers with examination of microstructure and analysis of organic matters. Paraloid B-72 layers were coated on samples from the colour layer of outer wall painting in Mireuk hall in Geumsan temple. On the basis of the previous examination result, it has made the samples which are similar to outer wall in Mireuk hall in Geumsan temple. The samples can be divided into two, one; 5% Paraloid B-72 coating and another is without coating. Then samples have been experimented under the compulsive environments of infrared radiation and immersion, thereafter compared the results of the damages and physical features between two samples. As a result of the comparison, the sample with Paraloid B-72 had more serious cracks, exfoliations and peeling layers than that of without Paraloid B-72. Otherwise, in the examination of ultraviolet radiation, the sample with Paraloid B-72 coating showed weaker physical properties, less density in structure of colour layer and less hardness in surface of colour layer than the sample without coating. The percentage of moisture content after the ultraviolet radiation was higher in the sample without Paraloid B-72 than the sample with Paraloid B-72 coating. Observing the conditions before the ultraviolet radiation, the sample with Paraloid B-72 coating demonstrated lower rate in moisture evaporation rate than the sample without Paraloid B-72. As a consequence, in examination of this samples, the change of physical features are increased in the sample with Paraloid B-72 coating than that without Paraloid B-72 when compulsive environment of heat, moisture and ultraviolet rays for a short term are imposed.

• Journal of Conservation Science
• /
• v.26 no.3
• /
• pp.325-334
• /
• 2010

In order to clarify the effect of consolidant, the artificial porous material with low intensity was manufactured using granite powder and Portland cement. We have prepared four kinds of alkoxysilane system consolidants, a acrylic resin and a epoxy resin and investigated about characteristics before and after consolidation. As a result of the research, Silres BS OH 100 was effective for density and surface hardness. SS-101 with hydrophobicity and Site SX-RO with hydrophilicity had the good durability over salts weathering. On the other hand, Syton HT-50 and Paraloid B72 were easily destructed by salt weathering because they were concentrated on surface area by the low penetration depth. Araldite 2020 was the most effective consolidant for improvement of physical properties.

• Journal of Conservation Science
• /
• v.29 no.1
• /
• pp.81-92
• /
• 2013

In the past, European material and method were applied to conservation of Buddhist mural paintings in Korea. At that time, there were inadequate to selection of materials in consideration of porosity and hydrophilicity, therefore insufficiency to assessing their suitability for materials. The treatment result of mural painting are dissatisfied with consolidation of painting layer using synthetic resin. Therefore, it has experimented on applying fixative for reinforcement of painting layer on Buddhist mural painting in order to establish the effects of conservation. In relationship of binder's viscosity, adhesion and penetrating depth, adhesion increased in high-viscosity specimen whereas it decreased in low-viscosity specimen. While the binder's penetrating depths show similar patterns, the surface's response and combination adjacent to painting layer have differences. Animal glue and methyl cellulose (MC) shows excellent performance in their reaction with soil and painting layer. It is estimated that the fixative penetrates deep into soil to produce a stable fixing effect. The viscosity of polyvinyl acetate resin (PVAc) and acrylic resins are low, and thus penetrates well into soil, but they adhere poorly to soil.