• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.26 no.5
• /
• pp.327-333
• /
• 2013

The purpose of this study is to predict sloshing pressure of a actual tank by using measured pressure in scaled down tank and to evaluate with structural strength of LNG Corner Block. For this purpose, we performed sloshing analysis about 138K class tank by using Ansys CFX program, and were measured both average pressure and maximum peak pressure according to scaled tank ratio. Also, measured pressure was converted to pressure of the actual tank by Froude scale law, and we conducted the evaluation of structural strength about the conner block of actual size KC-1.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.22 no.3
• /
• pp.379-385
• /
• 2012

This paper developes the navigation visual aid supporting a watch officer's situation awareness and analyzes its performance test result. Developing the equipment made from composite video sensor which transfer video signal, ranger laser measurement model which search out distance, Pan/ Tilt, center control device. The developed equipment with Pan/Tilt was made from high performance video sensor and ranger laser measurement. To make a real ship test, we carried on setting the developed equipment on ship, observed a danger factor and analyzed a image, and from that we can evaluate marine environment awareness. Through this result, the developed equipment can show effective ability of the awareness of the clearer check and resolution situation when compare with the binocular.

• Journal of Navigation and Port Research
• /
• v.39 no.4
• /
• pp.307-312
• /
• 2015

ARPA(Automatic Radar Plotting Aid) is a device to calculate CPA(closest point of approach)/TCPA(time of CPA), true course and speed of targets by vector operation of relative courses and speeds. The purpose of this study is to develop target acquisition and tracking technology for ARPA Radar implementation. After examining the previous studies, applicable algorithms and technologies were developed to be combined and basic ARPA functions were developed as a result. As for main research contents, the sequential image processing technology such as combination of grayscale conversion, gaussian smoothing, binary image conversion and labeling was deviced to achieve a proper target acquisition, and the NNS(Nearest Neighbor Search) algorithm was appllied to identify which target came from the previous image and finally Kalman Filter was used to calculate true course and speed of targets as an analysis of target behavior. Also all technologies stated above were implemented as a SW program and installed onboard, and verified the basic ARPA functions to be operable in practical use through onboard test.

• Journal of Navigation and Port Research
• /
• v.40 no.3
• /
• pp.97-103
• /
• 2016

The precise prediction of ships propulsion performance is very important to find out the ships optimum route. This paper describes the development of computer program to generate the database of propulsion performance for the ships optimum routing system. The propulsion performance of ship in the sea is caused by not only ships conditions such as drift and hull roughness, but also various sea conditions such as wave and wind. These prediction methods of added resistance are based on the ships speed trial analysis methods of the ISO 15016:2002 standard, and a few prediction methods of the wind and hull roughness are supplemented. These prediction methods have been applied to the comprehensive computer program. And the database calculation for the research ice breaker the Araon has been carried out, which shall be used for the calculation of optimum route. Furthermore, this program shall be used for the route optimization in global shipping routes.

• Journal of Navigation and Port Research
• /
• v.31 no.10
• /
• pp.813-818
• /
• 2007

There are the C.W.C and Towing Tank to the model-test equipments of the boat. A model testing of the high speed boat have a difficult in the performance verification because of very a small the scale-ratio of the ship-model and restricted by flow-velocity of the C.W.C and X-carriage velocity of the T.T. In general, the stepped hull boat is a high of fuel-efficiency because of the resistance reduction by a small wetted surface-area in correspond without stepped-hull boat. But It have a tendency to be bad the rolling performance by reduced stern wetted-area In this paper, the high speed stepped planning-boats with & without attached a stern body were performed to compare the effect of resistance and rolling performance by using sea model-test method.

• Journal of Navigation and Port Research
• /
• v.33 no.1
• /
• pp.35-41
• /
• 2009

A waypoint tracking algorithm(WTA) is designed for Unmanned Surface Vehicle(USV) in which water-jet system is installed for propulsion To control the heading of USV for waypoint tracking, the steering nozzle of water-jet need, to be controlled. Firstly, target heading is calculated by using the position information of waypoints input from the land control center. Secondly, the command for the steering nozzle of water-jet is calculated in real time by using the heading and the rate-of-turn( ROT) from magnetic compass, In this study, in order to consider the drift angle due to external disturbance such as wind and wave, the course of ground( COG) can be used instead of heading at higher speed than a certain value, To test the performance of newly-designed WTA, the tests were carried out in actual sea area near Gwang-an bridge of Busan. In this paper, the sea trial test results from WTA are analyzed and compared with those from manual control and those from commercial controller.

• Journal of Navigation and Port Research
• /
• v.35 no.10
• /
• pp.805-810
• /
• 2011

An experiment was carried out to figure out the instantaneous flow characteristics in the wake of the transom stern's 2-dimensional section by 2-frame grey level cross correlation PIV method at $Re=3.5{\times}103$, $Re=7.0{\times}103$. The stern angles of models were learning at $45^{\circ}$(Model "A"), $90^{\circ}$(Model "B") and $135^{\circ}$(Model "C") respectively based on the survey results of real ships. The depth of wetted surface is 40mm from free surface. As Reynolds number increases, vortices increase in volume and move their way to the downstream. Flow separation appeared at the end of model's bottom.

• Journal of Ocean Engineering and Technology
• /
• v.27 no.5
• /
• pp.88-92
• /
• 2013

The icebreaking research vessel (IBRV) ARAON had her second ice trial in the Arctic Ocean in the summer season of 2010. During the voyage, the local ice loads acting on the bow of the port side were measured using 14 strain gauges. These measurements were carried out in three icebreaking performance tests. To convert the measured strains into the local ice pressures, a finite element model of the instrumented area was developed. The influence coefficient method (ICM), which uses the influence coefficient from the finite element model, and the direct method, which uses the measured strain, were selected as the conversion methods. As a result, the maximum measured pressure was 1.236MPa, and the average difference between ICM and the direct method was about 5% for an area of $0.2m^2$. The pressure-area relationship of the measurement falls below the range of the existing pressure-area curve, which is due to the low ice strength of melted ice in the summer.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.24 no.4
• /
• pp.445-450
• /
• 2018

AIS is the most important navigation equipment for the identification of other ships, etc. However, the AIS overload problem has been raised recently due to an increase in AIS equipped vessels. The government is planning to introduce the wireless LTE network at 100 km offshore as part of the SMART-Navigation project. Continuous development and dissemination of the services available through such platforms will be necessary to achieve major goals such as marine accident prevention and environmental protection. In this study, we applied a WAVE communication system, which could be the basis for the development of such services. As a result, reliable data transmission was confirmed for a range of communication of approx. 5 miles, although the service was limited to 1 km in road traffic. Therefore, it is expected that WAVE communication technology will be used to prevent marine accidents through such efforts as collision avoidance and the transfer of marine safety information between ships.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.6 no.1
• /
• pp.1-24
• /
• 1969

Added masses of two-dimensional cylinders of curvilinear-element sections with chines, which are similar to marked V character ship sections with either single or double chines, oscillating at high frequency in a free surface of an ideal fluid are calculated for both vertical and horizontal vibration by employing two particular two-parameter families of the conformal transformation. The numerical results are graphically presented in the forms of added mass coefficient curves in terms of the sectional area coefficient and the half beam-draft ratio together with the section contours derived with the employed transformations, and discussed in comparision with those of the Lewis forms and of straightline-element sections with single chine for vertical vibration, and, for horizontal vibration, with those of the Lewis forms.