• Journal of the Society of Naval Architects of Korea
• /
• v.36 no.3
• /
• pp.1-7
• /
• 1999

This paper describes the modification of hull bottom for the air lubrication technique to the passenger boat in service at the Chung-Ju lake, which has a large beam-draft ratio. From numerical analysis of 2-D cavity problem by potential theory, the cavity shape, length and the pressure in cavity are estimated for the simplified geometry of hull bottom, and the non-dimensional parameters affecting air cavity phenomena are investigated. Extensive resistance tests for the model ship which has variation of step height and side strip have been performed to investigate the formation of air cavity and the drag reduction effectiveness. And also, the development of attached cavity to the bottom were observed from the flat bottom made by transparent acrylic plate. From this survey on the modification of bottom shape and the air lubrication technique, the total resistance of model ship could be reduced by about 25% at the design speed compared to the proto type hull form.

• Journal of the Society of Naval Architects of Korea
• /
• v.54 no.6
• /
• pp.501-514
• /
• 2017

In the previous research, a study was carried out to estimate the actual performance such as the propeller Revolution Per Minute (RPM) and engine power of a Liquefied Natural Gas Carrier (LNGC) using the full-scale measurement data. After the predicted RPM and engine power were verified by comparing those with the measured values, the suggested method was regarded to be acceptable. However, there was a limitation to apply the method on the prediction of the RPM and engine power of a ship. Since the information of route, speed, and environmental conditions required for estimating the RPM and engine power is generally regarded as the intellectual property of a shipping company, it is difficult to secure the information on a shipyard. In this paper, the RPM and engine power of the 151K LNGC was estimated using the combination of Automatic Identification System (AIS) and European Centre for Medium-Range Weather Forecasts (ECMWF) database in order to replace the full-scale measurement. The simulation approach, which was suggested in the previous research, was identically applied to the prediction of RPM and engine power. After the results based on the AIS and ECMWF database were compared with those obtained from the full-scale measurement data, the feasibility was briefly reviewed.

• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.9
• /
• pp.1170-1174
• /
• 2014

If cavitation occurs in propeller, it generates vibration and noise accordingly which results in low efficiency of propeller. It's important to increase cavitation inception speed(CIS) since the noise of cavitation increases significantly from the beginning of cavitation. This paper describes the result of actual observation and measurement onboard ship with controllable pitch propeller(CPP), so as to verify the first occurrence phenomenon of cavitation. The research suggests new type of controllable pitch propeller with improved CIS at the bolt as it started with bolt cavitation as result of observation. It's not found bolt cavitation on the CPP proposed in this paper, furthermore its CIS is increased approximately by 4.5 knots than the existing CPP. The result of the research can be used for development of low-noise CPP and improving performance of CIS.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.12 no.3
• /
• pp.209-216
• /
• 2009

IMO has established International Convention for the Control and Management of Ships' Ballast Water and Sediment 2004 in February 2004 in order to prevent transfer of aquatic organisms through ballast water. According to the Convention, Each countries are preparing ratification and legislation process and encouraging the development of treatment system to satisfy the performance standard in the Convention. This Electro-$Cleen^{TM}$ treatment system was granted IMO basic approval in March 2006, and final approval in October 2008. The Type Approval Certificate was issued in December 2008 by the Government of Republic of Korea. This paper considers the matter of principle mechanism, overview of the system, installation on shipboard and shipboard test results for the Electro-$Cleen^{TM}$. Shipboard tests with the 8300 GT M/V Yokohama and 27,000 DWT M/V Greenwing have already been conducted. These tests confirmed that the Electro-$Cleen^{TM}$ system satisfies all of the IMO standards and is suitable for installation in new and existing ships.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.19 no.1
• /
• pp.52-58
• /
• 2013

Operation Abstract : Operational cost required for navigating a ship may differ from according to type, scale, economic speed, navigation area and other factors. However, it is known that the fuel oil price ratio takes 50~60 %. It is the current trend because of the use of poor quality fuel and it is reviewed even for small to medium sized ships to save the operational costs due to the recent rise of international oil price. Furthermore, ocean carriers are taking action to low speed navigation as the alternative method of reducing fuel consumption. Hence, in this study, fuel consumption of main engine was measured by using actual operating ship data compared with sea speed at sea. It was suggested that the area of M/E's load(70 %) lower than NCR is the optimal navigating condition through the relation between speed and fuel consumption compared with advance ratio together with the load.

• Journal of the Society of Naval Architects of Korea
• /
• v.47 no.2
• /
• pp.150-162
• /
• 2010

Assessment of hydrodynamic performance of a ship hull has been focused on a model ship rather than a full-scale ship. In order to design the propeller of a ship, model-scale wake is often extended to full-scale based upon an empirical method or designer's experience, since wake measurement data for a full-scale ship is very rare. Recently modern CFD tools made some success in reproducing wake field of a model ship, which implicates that there are some possibilities of the accurate prediction of full-scale wakes. In this paper firstly the evaluation of model-scale wake obtained by Fluent package was performed. It was found that CFD calculation with the Reynolds-stress model (RSM) provided much better agreement with wake measurement in the towing tank than with the realizable k-$\varepsilon$ model (RKE). In the next full-scale wake was calculated using the same package to find out the difference between model and full-scale wakes. Three hull forms of KLNG, KCS, KVLCC2 having measurement data open for the public, were chosen for the comparison of resistance, form factor, and propeller plane wake between model ships and full-scale ships.

• KEPCO Journal on Electric Power and Energy
• /
• v.6 no.2
• /
• pp.163-171
• /
• 2020

A model test for assessment of towing stability and seakeeping of a multi-purpose mobile base (MMB) was performed in calm water and wave conditions. Scale ratio of the MMB was 1/48. Tension of the towing line was measured during tests to estimate effective power to tow the full scale MMB. The tests were repeated with towing speed. In addition, an inertial measurement unit was used to measure six DOF motion of the model. Seakeeping performance was assessed through the captive model test.

• Journal of the Society of Naval Architects of Korea
• /
• v.35 no.4
• /
• pp.11-18
• /
• 1998

This study describes sea trial tests for a waterjet propulsion system attached in the hybrid super high speed cargo ship named "Narae". A measuring technique of jet velocity, gross thrust and impeller torque for the waterjet system is explained. From the measured data in sea trial test, performance of the waterjet propulsion system is analyzed and compared with model test results of a similar waterjet system which was carried out in 1996. The erective horse power estimated from sea trial tests shows a good agreement with resistance test results of the model ship. The optimum rising height is estimated as 0.75 m, and the overall efficiency of the waterjet system is predicted as 0.315 at 15 knots. Useful data such as the pump performance, the jet efficiency, the losses of inlet duct and nozzle were obtained. Test results show a similar behavior to the model test results.

• Journal of the Society of Naval Architects of Korea
• /
• v.34 no.1
• /
• pp.50-59
• /
• 1997

Shipbuilder checks the status of main engine and propeller operation before sea trial. Generally these tests are carried out at a quay during fitting out of the ship. For these tests the operator has to estimate the maximum RPM with permissible torque and thrust to ensure the safety of the mooring line and ship. In this paper, the propeller characteristics according to the draft variation for a moored ship is inveatigated. From these tests, it is shown that shaft submergence is a dominant parameter in the propeller performance at shallow shaft submergence and that the propeller performance is dependent upon the propeller RPM when the shaft submergence is kept unchanged. In this study, a simple formula of the required thrust for a given propeller shaft submergence and propeller RPM is derived. 1be propeller thrust, which is calculated by another formula in case of dtep draft, is compared with results of bollard pull test for FPSO.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.25 no.7
• /
• pp.851-857
• /
• 2019

This study is about ship horsepower prediction of machine learning method using the big data of ship. Currently, new ships use the ISO15016 method to predict external environmental resistance through mathematical equations but due to complicated equations and requires many input variables so it is less applicable to be used in ship. In this recent research, we propose a model capable of predicting ship performance with high performance using SVM (Support Vector Machine) algorithm which shows excellent performance in recent prediction and recognition. The proposed predictive model has the advantage of being able to predict better performance than ISO15016 only if secured big data is used. In this study, we compared the ISO15016 technique and the SVM algorithm-based horsepower analysis method using the 178K bulk carrier's voyage data to reduce ship model data preparation, which is a disadvantage of ISO15016, and improve inaccurate horsepower prediction performance.