• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.1
• /
• pp.74-81
• /
• 2001

Dynamic pressure is one of the major sources on noise emission in oil hydraulic piston pump. This paper reports an experimental study of dynamic pressure characteristics in the cylinder bore of oil hydraulic piston pump. We experimently measured dynamic pressure at BDC with delivery pressure, rotational speed and oil temperature. Because the V-grooves at the ends of the kidney ports with three types valve plates. We hope this paper help to design of the valve plate in oil hydraulic piston pump.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.10a
• /
• pp.211-211
• /
• 2003

• Proceedings of the Korean Society of Laser Processing Conference
• /
• 1999.11a
• /
• pp.16-20
• /
• 1999

• Proceedings of the Korean Society of Laser Processing Conference
• /
• 2000.06a
• /
• pp.43-46
• /
• 2000

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.3
• /
• pp.28-38
• /
• 2003

Finite element analysis of cylinder heat/block compound under assembly, thermal and firing condition were performed. FE model including two cylinders with gasket, head bolts, liners and valve seats was used. FE modeling method and boundary conditions were introduced. Stress distribution and deformation of cylinder head and block under each loading condition were presented. Gasket pressure distribution and bore distortion level were predicted. Measured data of bore distortion was compared with the analysis results. The analysis result showed similar trends with the experimental data. High cycle fatigue analysis on the basis of this result has been performed in order to find the critical areas of the engine assembly.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.5
• /
• pp.174-181
• /
• 2002

Dynamic deformation of the cylinder bore during actual engine operation has an important effect on the combustion gas sealing, oil consumption, friction and so on. The dynamic analysis using the finite element method is performed to investigate the dynamic deformation of the cylinder bore subjected to forced vibration under excitation of the combustion gas pressure. However, this analysis requires large computer memory and tremendous solving time. The pseudo-static analysis can be an alternative to the dynamic analysis at the expense of accuracy. Dynamic analysis and static analysis results are presented for both closed-deck block and open-deck block that are respectively combined with the cylinder block, cylinder head, transmission, and oil pan.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.4
• /
• pp.39-48
• /
• 2005

Finite element analyses have been performed for the purpose of obtaining the robust and reliable design of engine cylinder block. Fatigue under high cycle operating loads is a primary concern and is evaluated by a probabilistic method. The robust and reliable design by a probabilistic method can provide satisfactory design conditions for the performance of the system under the influence of noise factors. Therefore, the design by this method will be desensitized to the uncontrollable noise factors. The simple methodology evaluates the distortion of main bore is proposed for the purpose of maintaining a well-controlled clearance between the crankshaft and main bores. The proposed methodology has proven a capability of predicting the distortion of the main bore under assembly, thermal, and firing loads. The calculated results are correlated well with the experimental ones.

• Journal of the Korea Convergence Society
• /
• v.12 no.2
• /
• pp.185-191
• /
• 2021

The characteristics of the foundry sand were analyzed for water jacket core required to prevent structural deformation from the heat generated in the cylinder bore during the casting of the cylinder block of an automobile. The sand core tensile strength tester, AFS-GFN, and optical microscope were used to evaluate the its properties. If the SiO2 content is high in the foundry sand, the dimensional defects and veining defects occur due to high temperature expansion. Also, if it is too low, the core breakage, porosities, chemical burn-on defects occur. The particle size index and grain shape influenced the core strength and resin consumption, resulting in fluctuations in defect types. The higher the alkalinity of the dried sand, the lower the core strength. And the more basic, the lower the core strength. At the resin content of 1.6~1.8%, the increase in core strength after 1 hour curing was approximately at its maximum.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.5
• /
• pp.211-221
• /
• 1998

Thermal behavior on the cylinder block of a 4-cylinder, 4-stroke 2.0L SOHC gasoline engine was numerically and experimentally analyzed. The numerical calculation was performed using the finite element method. The cylinder block was modelled as a three dimensional finite element by considering its geometry. The physical domain was devided into hexahedron elements. 16 thermocouples were installed at points of 2mm inside from cylinder wall near top ring of piston in cylinder block, which points have suffered major thermal loads and suggested as proper measurement points for engine design by industrial engineers. Under full load and 9$0^{\circ}C$ coolant temperature condition, temperature behavior of cylinder block according to engine speed were analyzed. The results showed that temperature rose gradually to conform to a function of 2nd~4th order of engine speed at intake side, exhaust and siamese side, respectively. As engine load was changed from 100 to 50% by 25% step, temperature curve also conformed to 2nd~7th order function of engine speed. Temperature differences by load condition were similar among 100, 75% and 50%. Under full load and coolant temperature of 11$0^{\circ}C$, temperature behavior were also analyzed and the result also showed conformance to 2n d~7th order function of engine speed. Temperature curve was transferred in parallel upwards corresponding coolant temperature rise.

• Korean Journal of Materials Research
• /
• v.11 no.11
• /
• pp.965-971
• /
• 2001

The objective of this study is to investigate the characteristics - microstructure, hardness, adhesive strength and friction coefficient - of the coatings with aging - treatment after optimizing internal- plasma spraying parameters for Al-30wt%Si powder as a basic research to manufacture the cylinder block bore for Al engine composed of Al-30wt%Si alloy on Al alloy, The optimum internal-plasma spraying parameters of Al-30wt%Si alloy are summarized as follows: voltage: 37.5V, current: 160A, working distance: 25mm, gun traverse speed: 4.5mm/s, rotating speed: 518m/min. The primary Si particles grew aggressively with increasing heat-treating temperature. The hardness of the as-sprayed coating was about Hv=275 but this value was abruptly decreased with increasing heat-treating temperature. And average friction coefficient of the coating was below 0.08 after heat treatment for 48h at $175^{\circ}C$.