• The Journal of the Korea institute of electronic communication sciences
• /
• v.18 no.1
• /
• pp.185-194
• /
• 2023

The 4-axis strain-gauge, which is widely applied to military weapon systems, is operated in poor temperature and vibration conditions, tolerance may increase and malfunctions may occur. To improve this, this paper proposes a signal-processing software technique for the tolerance of the 4-axis strain gauge applied to a military weapon system. First, the tolerance of the strain-gauge and the signal processing circuit according to the ambient temperature were evaluated and analyzed. Second, a software technique for processing the dead zone and offset area that can improve the tolerance of the strain-gauge is proposed. The experimental results applying the software technique confirmed that it operated normally in the temperature test and operation test. Therefore, the proposed software technique is valid and can be used as useful information to improve tolerance due to ambient temperature and vibration when designing a system using a strain-gauge.

• Journal of Satellite, Information and Communications
• /
• v.6 no.1
• /
• pp.80-85
• /
• 2011

In this paper, a software-based real-time GPS L1 receiver is proposed for the block correlation techniques. Recently various navigation satellite navigation receivers in the environment for the development of more efficient software-based real-time receiver need to be developed. It is composed of components such as signal supplier, signal acquisition, signal tracking, navigation data processing, and navigation solution. They are designed and implemented as component based software for enhancing reusability and modifiability for user to have more flexibility during development of receiver. This paper will describe design, implementation, and verification of the developed realtime software GNSS receiver.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.25 no.11
• /
• pp.1135-1141
• /
• 2014

Performing wideband DDC while quantizing signal over a wide dynamic range and high speed sampling rate have primarily been implemented in a hardware such as, FPGA or ASIC because of time-consuming job. Real-time wideband DDC SW, even though signal environment changes, adapt to signal environment flexibly and can be reused. In addition, it has a lower price than the hardware implementation. In this paper, we study the system design that can be stored in real time designing a high-speed parallel processing architecture for SW-based wideband DDC. Finally, applying a Ping-Pong Buffering mechanism for receiving a signal in real time and CUDA for a high-speed signal processing, we verify wideband DDC design procedure that meets the signal processing.

• The Journal of the Acoustical Society of Korea
• /
• v.36 no.1
• /
• pp.30-38
• /
• 2017

In this paper, we propose an underwater acoustic sensor fault detection method for passive sonar systems. In general, a passive sonar system displays processed results of array signals obtained from tens of the acoustic sensors as a two-dimensional image such as displays for broadband or narrowband analysis. Since detection result display in the operation software is to display the accumulated result through the array signal processing, it is difficult to determine the possibility where signal may be contaminated by the fault or failure of a single channel sensor. In this paper, accordingly, we propose a detection method based on the analysis of RMSCR (Root Mean Square Crossing-Rate), and the processing techniques for the faulty sensors are analyzed. In order to evaluate the performance of the proposed method, the precision of detecting fault sensors is measured by using signals acquired from real array being operated in several coastal areas. Besides, we compare performance of fault processing techniques. From the experiments, it is shown that the proposed method works well in underwater environments with high average RMS, and mute (set to zero) shows the best performance with regard to fault processing techniques.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2002.11a
• /
• pp.695-698
• /
• 2002

최근 시각 관련 측정기 개발에 대한 관심이 높아지고 있다. 이에 본 연구는 자동 시각 굴절력 곡률계의 전자 부문에 연동될 굴절력 측정 알고리즘을 개발하였다. 만약 자동화된 시스템이 광학계로부터 나오는 영상을 이용하여 내부 처리를 거친 후 정확한 시각 측정치를 검사자에게 알려줄 수 있다면 잘못 측정되는 측정 횟수를 크게 줄일 수 있을 것이다. 본 연구는 형태학적 필터링(morphological filtering)과 그레이-레벨의 신호 강조(signal enhance) 기술들을 이용하여 자동 시각 굴절력 측정 시스템에 연동될 측정 알고리즘을 개발하였다. 알고리즘에서는 광학계로부터, 도출된 영상으로부터 첫째로 형태학적 필터링 처리를 행하여 처리가 어려운 원 영상을 좀 더 다루기 쉬운 상태로 바꿔준 후 영상에 가해주는 그레이 수준 한계 기법을 통해 신호를 강조함으로써 영상의 그레이 값 분포가 다양함으로 인해서 발생되는 오차를 줄이게 된다. 그리하여 본 전자 부문 소프트웨어는 정확한 측정값 도출이 어려운 시각 영상에 적용되어 효과적으로 오차를 줄임으로써 보다 효율적인 시각 측정을 가능하게 하였다.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2000.10b
• /
• pp.935-938
• /
• 2000

본 논문은 광학 현미경을 컴퓨터 상에서 구현한 소프트웨어 시스템인 Medieye 시스템에 가장 큰 문제점인 대용량의 영상 데이터를 압축하는 기법을 제안하고, Medieye 시스템에 대하여 기술한다. 현재 구현된 Medieye 시스템은 환자의 조직 샘플에 대한 고해상도 디지털 영상을 인터넷 상에서 제공하고 있으며, 궁극적으로는 의료 기관 및 의학 연구 기관의 슬라이드로 꽉 찬 캐비넷을 디지털 저장시스템으로 대체하기 위한 클라이언트 서버 구조 기반의 소프트웨어 시스템이다. Medieye 시스템은 클라이언트 프로그램, 네트워크 서버, 데이터 서버 3 부분으로 구성되었고, 이들은 정해진 통신 규약에 따라 메시지를 서로 주고받음으로써 각 부분이 상호 독립적이다 이 시스템에 적용할 영상압축 기법은 블록 기반의 웨이블릿 변환을 이용한 영상 압축이다. 입력 영상 신호를 여러 개의 부밴드 영상으로 분해하고 각 부밴드 영상에 대하여 독립적으로 다시 작은 블록으로 나누어 각 부밴드의 특성에 맞도록 영상을 압축하는 알고리즘을 제안하였다. 이 기법은 제로 트리와 비슷한 성능을 보이면서도 구조가 비교적 간단하여 계산적인 면과 수행 속도 면에서 우수한 성능을 보여 준다.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.21 no.6
• /
• pp.615-632
• /
• 2008

The bridge health monitoring has become an important research topic in conjunction with damage assessment and safety evaluation of structures owing to the improvement of structural modeling techniques incorporating response measurements and the advancements in signal analysis and information processing capabilities. The bridge monitoring systems are generally composed of hardwares such as sensors, data acquisition equipment, data transmission systems, etc, and softwares such as signal processing, damage assessment, display and management, etc. In this paper, the research and development(R&D) activities on the information processing for structural health monitoring of bridges are reviewed. After a brief introduction to the process of bridge health monitoring, various information processing techniques including various signal processing and damage detection algorithms are introduced in detail. Several challenges addressing critical issues in the current bridge health monitoring system and future R&D activities are discussed.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2005.10a
• /
• pp.37-42
• /
• 2005

It is necessary that Fail-Safe Seaway technology providing a continuous navigation solution though fault of navigation system is occurred in sea. This paper focus on signal processing of GPS receiver, one of receivers using the software radio technology to implement a integrated radio navigation system including satellite-based and ground-based navigation systems. It is difficult to implement the software GPS receivers using a commercial processor bemuse of the heavy computational burden for processing the GPS signals in real time. This paper proposes an efficient multi-bit GPS signal processing scheme to reduce the computational burden for processing the GPS signals in the software GPS receiver. The proposed scheme uses a compression concept of the multi-bit replica signals and patterned look-up table method to generate the correlation value between the GPS signals and the replica signals.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.17 no.4
• /
• pp.248-261
• /
• 1997

Ultrasonic pattern recognition is the most effective approach to the problem of discriminating types of flaws in weldments based on ultrasonic flaw signals. In spite of significant progress in the research on this methodology, it has not been widely used in many practical ultrasonic inspections of weldments in industry. Hence, for the convenient application of this approach in many practical situations, we develop an intelligent ultrasonic signature classification software which can discriminate types of flaws in weldments based on their ultrasonic signals using various tools in artificial intelligence such as neural networks. This software shows the excellent performance in an experimental problem where flaws in weldments are classified into two categories of cracks and non-cracks. This performance demonstrates the high possibility of this software as a practical tool for ultrasonic flaw classification in weldments.

• The KIPS Transactions:PartB
• /
• v.9B no.6
• /
• pp.727-734
• /
• 2002

Currently. people become interested in the development of measuring instrument related to eyesight. In this study, we developed software of electronic part in automatic refracto-keratometer. If an automatic system, which uses images from an optical instrument, can inform the in-spector of an accurate eyesight measured value after the internal process, the frequency of mistakenly observed value will be reduced considerably. This software is using morphological filtering and gray-level signal enhancing techniques. The morphological filtering is the first process, from images of the optical instrument, to transform an original image which is hard to process into manageable one. The second process is a signal enhancing technique to the first processed image using gray -level thresholding technique and is used to reduce an error caused by the variety in distribution of the gray value of image. Therefore, this software system in electronic part will make more effective eyesight measurement by reducing the error effectively when applied to the optical image which is difficult to get accurate measurement value.