• Journal of the Microelectronics and Packaging Society
• /
• v.17 no.3
• /
• pp.27-32
• /
• 2010

For the flip chip joints processed using Cu pillar bumps and Sn pads, thermal cycling and high temperature storage reliabilities were examined as a function of the Sn pad height. With increasing the height of the Sn pad, which composed of the flip chip joint, from 5 ${\mu}m$ to 30 ${\mu}m$, the contact resistance of the flip chip joint decreased from 31.7 $m{\Omega}$ to 13.8 $m{\Omega}$. Even after thermal cycles of 1000 times ranging from $-45^{\circ}C$ to $125^{\circ}C$, the Cu pillar flip chip joints exhibited the contact resistance increment below 12% and the shear failure forces similar to those before the thermal cycling test. The contact resistance increment of the Cu pillar flip chip joints was maintained below 20% after 1000 hours storage at $125^{\circ}C$.

• Journal of the Microelectronics and Packaging Society
• /
• v.28 no.2
• /
• pp.95-103
• /
• 2021

Sn-58Bi-xRu composite solders were prepared by adding Ru nanoparticles to Sn-58Bi, a typical low-temperature solder, and the interfacial reaction and solder joint reliability were analyzed by reacting with Cu/OSP and ENIG surface treated PCB boards. The Cu₆Sn₅ IMC formed by the reaction with Cu/OSP had little change in thickness depending on the Ru content, and ductile fracture occurred inside the solder during the high-speed shear test without any significant change even after 100 hr aging. In reaction with ENIG, the Ni₃Sn₄ IMC thickness tended to decrease as the Ru content increased, and ENIG-specific brittle fracture was found in some specimens. Since Ru element is not found near the interface, it is judged not to be significantly involved in the interfacial reaction, and it is analyzed that it mainly exists together with the Bi phase.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.16 no.5
• /
• pp.957-968
• /
• 2021

To improve the data on reliability of the onshore fish farm water quality monitoring system and operate the system efficiently, the water quality data of the onshore seawater fish farms which are progressing test operation, and the marine environmental information network(Wando tidal station) were compared and analyzed. Furthermore, data validation, data range filters, and data displacement checks were applied to analyze the data in a way that eliminates the data errors in water quality monitoring systems and increases the reliability of measurement data.

• Journal of the Society of Naval Architects of Korea
• /
• v.29 no.4
• /
• pp.234-243
• /
• 1992

Fatigue crack initiation life has a wide scatter and this makes the fatigue design of structural members difficult. In order to make the fatigue life distribution clear, it is required to prepare a large number of specimens and repeat the fatigue tests under the same loading condition. Such fatigue tests usually take much time and cost. In this study, a fatigue testing method using a multi-notched test specimen for the purpose of estimating the distribution function of fatigue crack initiation life by small number of fatigue tests is used. The purpose of this study is to verify the above fatigue testing method of a multi-notched specimen by using Bayesian reliability analysis, Least square method and Skewness method for the determination of unknown Weibull parameters. The multi-notched specimen is a specimen in which several tens of statistically identical notches are prepared.

• Journal of Aerospace System Engineering
• /
• v.13 no.3
• /
• pp.48-55
• /
• 2019

This paper presents a study on Fault History Management Equipment (FHME) of Unmanned Aerial Systems (UAS). UAS comprise of various types of electronic equipment for high reliability design for flight safety. Consequently, it is mandatory for each on-board equipment to have its own Built-In-Test (BIT) function, because rapid fault-detections for UAS are necessary. FHME is developed for the purposes of display, storage and management of such BIT results on ground. This paper describes the outline, development requirements, design and verification process of FHME.

• Geophysics and Geophysical Exploration
• /
• v.19 no.4
• /
• pp.187-199
• /
• 2016

In order to delineate the soft ground distribution, an integrated geostatistical analysis was performed using the MASW (Multichannel Analysis of Surface Wave) which has the information of overall region and CPTu (Piezo Cone Penetration Test) which provides the direct information of the measuring point of the ground. MASW results were known to have close relationship with the ground stiffness. This correlation was confirmed through the comparison of MASW data obtained from two survey lines to the laboratory test with extracted soil samples. 3D physical property distribution in the study area was acquired by geostatistical integrated analysis with the data of tip resistance ($q_c$) and pore pressure (u) from the CPTu obtained at 6 points within the study area. The integrated analysis was conducted by applying the COSGSIM (Sequential Gaussian Co-Simulation) technology which can carry out the simulation in accordance with the spatial correlation between the MASW results and both tip resistance and pore pressure. Besides the locations of CPTu, borehole investigations were also conducted at two different positions. As a result, the N value of SPT and borehole log could be secured, so these data were used for the analysis of the geotechnical engineering accuracy of the integrated analysis result. For the verification of reliability of the 3D distribution of tip resistance and pore pressure secured through integrated analysis, the geotechnical information gained from the two drilling areas was compared, and the result showed extremely high correlation.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.5
• /
• pp.502-508
• /
• 2021

Predicting the settlement of soft ground is an important aspect of soft ground design. In this study, a method is proposed that increases the reliability of settlement predictions based on-site investigation data, including piezocone penetration test results, at the Gimhae-Jinyoung district, adjacent area to the Nakdong River. Soils in the area waweres classified using the Robertson Chart (1986, 1990), and theoretical settlement was calculated using the equations proposed by Terzaghi (1925) and Sanglerat (1972). SPSS was used to obtain the correlation between theoretical and measured settlements. Results produced settlement prediction errors for the Terzaghi and Sanglerat methods of 17.28% and 26.96%, respectively. A correction factor calculated by SPSS correlation analysis for the relation between and theoretical and measured settlements is proposed that improves the reliability of settlement prediction in soils of the classification examined.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.20 no.2
• /
• pp.331-346
• /
• 2018

In the tunnel of domestic high - speed railway, the main fire - fighting facility, fire - extinguishing passageway, is installed. However, due to the high pressure of the high - speed train, frequent breakage and maintenance are caused by strong shock and long - term vibration. In order to solve these problems, it is necessary to improve the fire door, but in Korea, it is installed by submitting a certificate by simple KS F 2296 performance test. At present, it is developed as a simple test certification by producing a real scale fireproof door without the theoretical examination in advance, so that a high cost for improvement is occurring in Korea. Therefore, through this study, structural analysis study which can preliminary structure review was carried out in order to design the refuge connection passage fire door and to improve the performance improvement. In order to secure the reliability of the result value, the official authentication test (KS F 2296) were compared.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.5
• /
• pp.648-655
• /
• 2020

The firing pin of modern automatic rifles detonates the primer of loaded ammunition via a hammer. During this process, the firing pin receives an impact load and repetitive force throughout the life of the rifle. An endurance test of a rifle showed that the firing pin breaks prematurely at 96.26% of life. Accordingly, a case study was conducted through cause analysis and a reconstruction test. Optical microscopy and scanning electron microscopy of the broken surface of the firing pin showed that a crack began in the circumferential direction of the surface, resulting in a fatigue crack to the core after repeated impact. Crack growth and fatigue destruction occurred at the end due to the repetitive impact and was estimated using a notch. For verification, a sample that produced a 0.03mm circumferential notch was broken at 64.25% of life in the reconstruction test. A test of breakage according to the notch types showed that a 0.3mm and a 0.5mm one-side notch were broken at 66.53% and 50.76%, respectively, and a 0.03mm six-point notch was broken at 85.65%. The endurance life of a sample firing pin with a rough surface and tool mark was examined, but an approximately 381 ㎛ internal crack formed. Through this study, failure for each notch type was considered. These results show that quality control of the notch and surface roughness is essential for ensuring the reliability of a component subjected to repeated impact.

• Fire Science and Engineering
• /
• v.28 no.2
• /
• pp.34-39
• /
• 2014

It is necessary to enhance its availability and reliability of performance based fire design of building with various type of database such as experiments, survey and fire properties and so on. In order to utilize to the performance based fire design, the present study has been performed a series of experiments to investigate the burning characteristics of building materials for two types of interior board and three types of interior louver. The burning test has been also conducted for different thickness because it may show different characteristics of burning behavior such as flame spread rate and flame propagation time. The result shows that the effective heat release per unit mass of interior materials were almost constant with 15.3~16.9 MJ/kg regardless of its thickness while the peak heat release rate and maximum $CO_2$ concentration was varied with thickness.