• Journal of Korean Society of Environmental Engineers
• /
• v.33 no.3
• /
• pp.183-190
• /
• 2011

This study investigated the emissions characteristics of air freshener using small emission chamber method. The emission of VOCs from air freshener were determined in the small chambers in the temperature (25, $30({\pm}1)^{\circ}C$), relative humidity ($50{\pm}5%$), ventilation rate (0.3, 0.5, ($0.8({\pm}0.005)/hr$), and sample loading factor ($1.4{\sim}551.0g/m^2$) in this study. The emission tests from air freshener for sample loading factor resulted in TVOC emission rates of $0.7{\sim}64.4mg/m^2{\cdot}h$ after 5 hours. For most target VOCs such as limonene, ${\alpha}$-pinene and linalool, higher temperature and ventilation rate levels exhibited increased emission rates.

• Journal of the Korean Vacuum Society
• /
• v.11 no.2
• /
• pp.87-96
• /
• 2002

Outgassing from such sources as paints, coatings, adhesives and other non-metallic surfaces can contaminate satellites, especially second surface mirror and optical lens, it cause satellite to fail in own missions. The vacuum bake-out test using high temperature(more than $85 ^{\circ}C$)and high vacuum(less than $5.0{\times}1-^{-3}$ Pa) certify that the components of satellite work properly and can survive and operate in space environment like high vacuum. In the bake-out chamber installed at SITC of KARI, Rotary vacuum pump and Booster pump produce low vacuum of 5.0 Pa, and then two cryopumps produce high vacuum of below $5.0{\times}10^{-3}$ Pa. Also 48 ceramic heaters were provided to simulate high temperature. During the vacuum bake-out test, we detected contaminants using RGA(Residual Gas Analyzer) and measure the outgassing rate of the contaminant using the TQCM(Thermoelectric Quartz Crystal Microbalance). Also, IR/UV Spectrometer and witness plate be used to certify that the components were suitable for the spacecraft. This paper includes the preparation and procedures of the bake-out test for SAR(Solar Array Regulator) and MLI(Multi Layer Insulator), which were the components of the spacecraft. Especially, we discussed the methods and results of the contamination measurement. In the bake-out for SAR, the contamination was measured continuously although it was on the decrease from TQCM results. And RCA established that it is a highly polymerized compound. In the MLI bake-out using RGA and witness plate, we didn't detect any contamination materials.

• Ecology and Resilient Infrastructure
• /
• v.4 no.4
• /
• pp.187-192
• /
• 2017

This study evaluated the reduction performance of ambient temperature and the amount of evaporation that takes place depends on the temperature difference of paving blocks which are used in the sidewalk, roadway, parking lot, park, plaza, and etc. The water-retentive block of the LID (Low Impact Development) practice was compared with the conventional concrete block. For the quantitative performance evaluation, experiments were performed in a climatic environment chamber capable of controlling the climatic environment (solar radiation, temperature, humidity, rainfall, and snowfall). The method for performance evaluation was proposed using temperature, humidity, and ambient air of paving blocks which changes according to the solar radiation and the wind speed after the rainfall. As a result, the evaporation amount of the water-retentive block was 2.6 times higher than that of the concrete block, the surface temperature of water-retentive block was $10^{\circ}C$ lower than the concrete block, and the air temperature of water-retentive block was $4.6^{\circ}C$ lower than the concrete block. Therefore, it is analyzed that the water-retentive block with a large amount of evaporation is more effective in reducing the urban heat island phenomenon as compared with the concrete block.

• Particle and aerosol research
• /
• v.13 no.3
• /
• pp.105-110
• /
• 2017

Real-time measurements of fine particles from stack emission gases are necessary due to the needs of continuous environmental monitoring of PM10 and PM2.5. The porous tube dilutor using hot and cold dilutions was developed to measure fine particles without condensable particles from highly humid emission gases and compared to the commercialized ejector-type dilutor. Particle size distributions were measured at the emission gases from a diesel engine and a coal-fired boiler. The porous tube dilutor could successfully measure the accumulation mode particles including relatively large particles more than $3{\mu}m$ without nuclei particles, while the ejector dilutor detected some condensable particles and could not detect large particles. The porous tube dilutor could successfully remove the already condensed water droplet particles generated by a humidifier in a $30m^3$ chamber.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.05a
• /
• pp.224-227
• /
• 2007

This paper introduces the results of acoustic loads test conducted on the upper stage assembly of KSLV-I, which is the first Korea space launch vehicle. A launch vehicle and its payloads are subjected to severe acoustic pressure loading when they lift off and ascent during the transonic periods. Acoustic loadings are spreaded out broad frequncy-spectrum up to 10,000Hz. Acoustic loads are a primary source of structural random vibration of the upper stage and payloads. Therefore, in order to verify the structural integrity of the upper stage assembly of KSLV-I and the survivability of its components under severe random vibration environment, acoustic loads test is conducted in the high intensity acoustic chamber with 142dB (overall SPL). The results show the structural design and component random vibration specifications well meet with the environmental requirements.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.11a
• /
• pp.269-272
• /
• 2009

Catalytic decomposition of nitrous oxide was investigated experimentally. Two noble metal catalyst (Pt, Ir) were chosen to decompose nitrous oxide. Each catalyst was tested with different chamber pressure and preheating temperature. Ir decomposed $N_2O$ at lower temperature ($230^{\circ}C$) and suitable for $N_2O$ decomposition. In addition, the minimum required preheating temperature decreased as the chamber pressure increased. However, deactivation of Ir catalyst was observed during the experiments.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.05a
• /
• pp.867-872
• /
• 2002

A high intensity acoustic test facility is constructed at Korea Aerospace Research Institute (KARI) by 2003. The reverberant chamber of the facility has a volume of 1,228 cubic meters and shall provide an acoustic environment of 152 dB over the frequency range of 25 Hz to 10,000 Hz. The facility consists of a large scaled reverberant chamber, acoustic power generation systems, gases nitrogen supply systems, and acoustic control systems. This paper describes how the basic parameters of a chamber and power generation systems are controlled to meet the requirement of the test. The volume of a reverberant chamber is controlled by the size of test objects and the reverberant characteristics of a chamber. The capacity of acoustic power generation systems is determined by the energy absorption of a chamber and the efficiency of acoustic modulators. Simple math is employed to calculate the required power of acoustic modulators. Moreover, the paper explains how the distribution of sound pressure level at low frequency is checked by analytical and numerical methods.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2018.06a
• /
• pp.76-76
• /
• 2018

LCD 디스플레이 크기는 점차 대형화를 이루면서, 현재 LCD 디스플레이 크기는 3,000*3,320mm 크기까지 증가하여 개발이 활발이 이루어지고 있다. 디스플레이의 크기가 증가함에 따라 제조 장비의 크기도 증가되어야 하므로, LCD 디스플레이 CVD 공정에 사용되는 4,200*3,300mm 크기의 대형 Aluminium Vacuum Chamber 에 피막두께 $15{\mu}m$ 이상을 구현함과 동시에 두께 균일도가 우수하며 염수분무시험으로 168시간 이상의 내식성 확보가 가능한 양극산화조건 개발을 위하여 양극산화 피막의 각종 특성 평가를 실시하였다. 양극산화 피막 두께 측정은 와전류(Eddy Current)의 원리를 이용한 비파괴식 두께 측정법(ISO 2360, ASTM D 7091)을 적용하였으며, 염수분무시험 방법은 (KS D 9502)을 적용하였으며, HCl bubble stream 시험 방법은 HCl 5% 농도를 투명 아크릴 튜브에 채운후 bubble stream 을 종점으로 하여 평가를 실시하였으며, 열충격을 이용한 도금밀착성(KS D 0254), 도장접착력(ASTM D 3359) 등을 이용하여 전해조건 및 전해액 농도에 따른 피막 특성 비교평가를 실시하여 최적의 대형 Aluminium Vacuum Chamber 양극산화 전해 조건을 개발하여 4,200*3,300mm 크기의 대형 Aluminium Vacuum Chamber 제조를 목적으로 하였다.

• Journal of the Korean Geotechnical Society
• /
• v.25 no.2
• /
• pp.67-77
• /
• 2009

In this study, the relations of cone tip resistances (qc) and DMT indices of cemented sand are analyzed from a series of calibration chamber tests. The experimental results show that, with increasing the cementation level, three DMT indices also increase. The CPT and DMT do not appear to properly reflect the cementation effect of sand, since the penetration induces the damage of cementation. Nevertheless, the DMT is more sensitive to deformation characteristics of cemented sand than CPT. It is also observed that the $E_D/q_c$ ratio of cemented sand is larger than that of uncemented sand. However, the $K_D-q_c/{\sigma}_v'$ relation is independant of cementation, unlike the result of previous study. In addition, this study evaluates the constrained modulus and cohesion intercept of cemented sand using the relation between cone resistance and dilatometer constrained modulus ($M_D$).

• The Proceeding of the Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.4 s.60
• /
• pp.48-52
• /
• 2006

2006 CISPR 총회가 스웨덴 스톡홀름 KISTA에서 개최되었다. CISPR I 회의는 9월 18일부터 20일까지 3일간 WG2 및 WG4를 중심으로 진행되었으며, WG1과 WG3 회의는 9월 20일 오후에 있었다. 우리나라에서는 WG1에 두 가지 제안을 발표하였다. 하나는 2004년 중국 상해 회의에서 처음 제안하여 2005년 남아공 케이프타운 회의에서 Task Force가 구성된 대형 시험품에 대한 CISPR 20의 외부 방사내성 시험레벨에 관한 것이다. 2006년 1월 미국 산타페에서 열린 TF 회의에서 시험결과에 대한 기술적 토론이 있었으며, Round Robin Test(RRT)를 실시하기로 결정되었다. RRT시험은 7월 중순에 실시되었으며, 참여한 시험소는 영국의 SONY, 네덜란드의 Philips, 독일의 SHARP 이었으며, 국내의 여러 EMC 시험소도 추후에 참여하였다. RRT 시험의 결과 및 분석이 이번 스톡홀름 회의에서 발표되었다. 또한, CISPR 13의 방사성 방출(RE)의 측정거리 기준점의 변경에 관한 것이다. 본 고에서는 TV 수신기에 대한 RRT 시험결과 및 분석에 대한 발표 내용을 소개하고자 한다. CISPR 20의 외부 전자기장 내성 시험은 0.8 m인 개방형 스트립라인(Open Strip-line: OSL)내에 시험품을 설치하고 $150kHz{\sim}150MHz$에서 시험하도록 규정하고 있다. OSL에 설치할 수 없는 대형기기는 IEC 61000-4-3에 따라서 주파수 범위 $80MHz{\sim}150MHz$까지 동일한 한계치로 전자파무반사실에서 시험하도록 규정되어 있다. 이에 대해 국내 제조업체 및 EMC 전문가들로 구성된 CISPR I 국내 위원회에서는 IEC 61000-4-3에 의한 전자파무반사실(챔버)에서의 내성시험이 CISPR 20에 의한 OSL에서의 내성시험보다 가혹하다는 문제 제기가 있었다. 이것이 본 안건에 대한 배경이다 지금까지 진행되어 왔던 내용을 요약해 보면 2004년 상해 회의에서, 수치해석 및 측정비교를 통하여 CISPR 20에서 규정하고 있는 OSL 전기장 교정방법의 개선의 필요성과 OSL에서 시험할 수 없는 대형 시험품에 대하여 시험레벨을 조정할 것을 지적하였다. 2005년 케이프타운 회의에서는 실제적으로 TV 방송 수신기 및 관련기기가 두가지 방법으로 시험되었을 때 시험결과에 미치는 영향을 시험품의 전기장 내성 레벨로 비교하였으며, 전자파무반사실에서 시험할 경우 시험레벨이 12 dB 낮추도록 보정되어야 할 것을 제안하였다. 2006년 이번 회의에서는 세계 각국의 시험소와 비교시험을 통하여 나타난 OSL과 전자파무반사실 간의 시험결과의 차이 및 이에 대한 원인을 분석하여 보고하였다. OSL과 전자파무반사실 비교시험에서 나타난 차이는 평균적으로 9 dB의 차이로 나타났으며, 주요 원인은 OSL에서 적용하고 있는 시험품을 OSL내부에 설치한 후 시험품에 의해 변경된 전기장의 세기를 보정해 주는 인자(k2)로 인한 차이(6 dB)와 OSL 내부의 전기장의 세기와 전자파무반사실 균일장 영역의 전기장의 세기의 차이(3 dB)이다.