• Journal of the Korean Geosynthetics Society
• /
• v.17 no.2
• /
• pp.41-49
• /
• 2018

The purpose of this study is to fabricate a full scale road embankment using lightweight air foamed soil as a soil material on soft ground and to investigate its material characteristics and behavior in order to promote dredged soil utilization and minimize ground improvement. As a result of the laboratory test of the onsite mixed samples, the total unit weight of the specimens decreased almost linearly until curing 28 days. In particular, the total unit weight after 28 days of curing was reduced to about 81% of the slurry state before curing, which will be useful in the formulation of similar native soil materials in the future. The unconfined compressive strength began to decrease with the 14th day of curing as shown in the previous study. When the cement content is increased, the strength decreases sharply at a small strain change after the occurrence of the maximum compressive strength, and the maximum strength is exhibited in a range of a smaller axial strain than normal range. The settlement at the surface layer of the ground due to the lightweight embankment was about 1 / 2.75 of the soil embankment and was in agreement with the unit weight ratio (1 / 2.7) of the embankment materials. This indicates the cause and effect of the settlement due to the difference in self weight of the embankments. Also, the difference in settlement between soil and lightweight embankment increased with increasing depth. This shows that the difference in the point at which the settlement is terminated is clear. The ground horizontal displacement under the lightweight embankment was about 15~20% smaller than that of the soil embankment and the depth of occurrence was also 4.5~5.0m shallower in the lightweight embankment.

• The Korean Journal of Ecology
• /
• v.25 no.3 s.107
• /
• pp.189-195
• /
• 2002

In order to elucidate the budget and cycling of Nitrogen and Sulfur, essential elements and principal constituents of acid rain, their input through precipitation, and their output by streamflow were quantified in coniferous and deciduous forested watersheds, using combination of nutrient concentration and hydrological analysis, in Kwangnung Experimental Forest from July 1991 to December 1993. Amount of annual mean precipitation was $12,916\;ton{\cdot}ha^{-1}{\cdot}yr^{-1}$, annual mean runoff $5,094\;ton{\cdot}ha^{-1}{\cdot}yr^{-1}$(39%), $7,467\;ton{\cdot}ha^{-1}{\cdot}yr^{-1}$(59%) in coniferous and deciduous forest watersheds, respectively. Amounts of annual input of $N({NO_3}^-+{NH_4}^+)$ and ${SO_4}^{2-}$ through preciptation were 12.5, $81.72\;kg{\cdot}ha^{-1}{\cdot}yr^{-1}$, repectively. Annual output via runoff of $N({NO_3}^-+{NH_4}^+)$ and ${SO_4}^{2-}$ were 0.06, $39.23\;ton{\cdot}ha^{-1}{\cdot}yr^{-1}$ in the coniferous forest watershed ecosystem, and 0.15, $55.46\;ton{\cdot}ha^{-1}{\cdot}yr^{-1}$ in the deciduous one, respectively. On the basis of annual nutrient input and output, the annual budget of $N({NO_3}^-+{NH_4}^+)$ and ${SO_4}^{2-}$ were +12.46, $+42.49\;ton{\cdot}ha^{-1}{\cdot}yr^{-1}$ in the coniferous forest watershed, and +11.35, $+26.26\;ton{\cdot}ha^{-1}{\cdot}yr^{-1}$ in the deciduous one. Thus $N({NO_3}^-+{NH_4}^+)$ and ${SO_4}^{2-}$ were accumulated in both forested watershed ecosystems.

• The Journal of Korean Academy of Prosthodontics
• /
• v.47 no.1
• /
• pp.46-52
• /
• 2009

Statement of problem: Recently, titanium has become popular as superstructure material in implant dentistry because titanium superstructure can be easily milled by means of computer-aided design and manufacture (CAD/CAM) technique. But retention form such as nail head or bead cannot be cut as a result of technical limitation of CAD/CAM milling and bond strength between titanium and porcelain is not as strong as that of conventional gold or metal alloy. Purpose: The objective of this study was to evaluate the shear bond strength of three different materials: heat curing resin, composite resin, porcelain which were bonded to grade II commercially pure Titanium (CP-Ti). Material and methods: Thirty seven CP-Ti discs with 9 mm diameter, 10 mm height were divided into three groups and were bonded with heat curing resin (Lucitone 199), indirect composite resin (Sinfony), and porcelain (Triceram) which were mounted in a former with 7 mm diameter and 1 mm height. Samples were thermocycled for 1000 cycles at between $5-55^{\circ}C$. Shear bond strength (MPa) was measured with Instron Universal Testing Machine with cross head speed of 1 mm/min. The failure pattern was observed at the fractured surface and divided into adhesive, cohesive, and combination failure. The data were analyzed by one-way ANOVA and Scheffe's multiple range test (${\alpha}=0.05$). Results: Lucitone 199 ($17.82{\pm}5.13\;MPa$) showed the highest shear bond strength, followed by Triceram ($12.97{\pm}2.11\;MPa$), and Sinfony ($6.00{\pm}1.31\;MPa$). Most of the failure patterns in Lucitone 199 and Sinfony group were adhesive failure, whereas those in Triceram group were combination failure. Conclusion: Heat curing resin formed the strongest bond to titanium which is used as a CAD/CAM milling block. But the bond strength is still low compared with the bond utilizing mechanical interlocking and there are many adhesive failures which suggest that more studies to enhance bond strength are needed.

• The Journal of Korean Academy of Prosthodontics
• /
• v.47 no.1
• /
• pp.61-69
• /
• 2009

Statement of problem: Porcelain veneers have become a popular treatment modality for aesthetic anterior prosthesis. Fitting porcelain veneers in the mouth usually involve a try-in appointment, which frequently results in salivary contamination of fitting surfaces. Purpose: An in vitro study was carried out to investigate the effect of silane treatment timing and saliva contamination on the resin bond strength to porcelain veneer surface. Material and methods: Cylindrical test specimens (n=360) and rectangular test specimens (n=5) were prepared for shear bond test and contact angle analysis. Whole cylindrical specimens divided into 20 groups, each of which received a different surface treatment and/or storage condition. The composite resin cement stubs were light-polymerized onto porcelain adherends. The shear bond strengths of cemented stubs were measured after dry storage and thermocycling (3,000 cycles) between 5 and $55^{\circ}C$. The silane and their reactions were chemically monitored by using Fourier Transform Infrared Spectroscopy analysis (FTIR) and contact angle analysis. One-way analysis of variance (ANOVA) and Dunnett's multiple comparison were used to analyze the data. Results: FT-IR analysis showed that salivary contamination and silane treatment timing did not affect the surface interactions of silane. Observed water contact angles were lower on the saliva contaminated porcelain surface and the addition of 37% phosphoric acid for 20 seconds on saliva contaminated porcelain increased the degree of contact angle. Silane applied to the porcelain, a few days before cementation, resulted in increasing the bond strength after thermocycling. Conclusion: Within the limitation of this study, it can be concluded that it would be better to protect porcelain prosthesis before saliva contamination with silane treatment and to clean the contaminated surface by use of phosphoric acid.

• The Journal of Korean Academy of Prosthodontics
• /
• v.52 no.2
• /
• pp.113-120
• /
• 2014

This study will evaluate the effectiveness of various pretreatments when fiber-reinforced composite (FRC) post is bonded to endodontically treated tooth with resin cement. Materials and methods: Canal shaping of FRC post (DT Light post, Size 3, Bisco Inc., Schaumburg, IL, USA) was performed on endodontically treated premolars at 1.5 cm from CEJ. Samples were divided into 6 groups of surface treatment after conventional washing and drying to the canal. Total of 24 FRC posts were randomly divided into 6 groups of surface treatment as follows: Group C: control - no surface treatment, Group A: airborne-particle abrasion (Cojet sand, 3M ESPE), Group S: silanization (Bis-silane, Bisco Inc.), Group M: universal primer (Monobond-plus primer, Ivoclar Vivadent Inc.), Group AS: silanization after airborne-particle abrasion, Group AM: universal primer treatment after airborne-particle abrasion. Pretreated fiber posts were cemented with resin-based luting material and photo-polymerized and cut to the thickness of 1 mm. Push-out test using a universal testing machine was performed. Bonding failure strength of post dislodgement was measured and the type of bonding failure was classified. Data were analyzed with Kruskal-Wallis test and multiple comparison groups were performed using Tukey HSD value of rank test (${\alpha}=0.05$). Results: Group AS showed significantly highest bonding strength. Group S, group AM, group A, and group M showed lower bonding strength in order. The control group showed the lowest bonding strength. Conclusion: Surface treatment with silane showed to be the most effective of the surface pretreatment methods for cementation of FRC post. Surface treatment with universal primer showed no significant difference compared with no surface treatment group as for bonding strength.

• Korean Journal of Poultry Science
• /
• v.28 no.2
• /
• pp.99-106
• /
• 2001

Pathologic changes and distribution of viral antigen as determined by immunohistochemistry were compared among 4-wk-old specific-pathogen free (SPF) chickens inoculated intratracheally with velogenic vis-cerotropic Newcastle disease virus isolated in Korea. Although the pattern of organ involvement and severity of lesion was different among chickens infected with different velogenic viscerotropic Newcastle disease (VVND) viruses, the pathological types of lesion was similar among the chickens. Severe lymphocytic necrosis and depletion were main histologic lesions in the immune related organs such as thymus, Fabricius bursa and spleen. The frequency of IP positive staining was variable depends on the types of tissues but not types of the kinds of VVND viruses infected. Brain, Fabricius bursa, thymus, cecal tonsil and trachea were IP positive with fairly high frequency and spleen, lung, proventriculus, intestine, pancreas, liver, kidney, heart and Harderian gland were with relatively low frequency. These results suggest that histologic evaluation and viral antigen specific immunohistochemical staining methods to determine virus distribution will be useful for pathogenic study of velogenic viscerotropic Newcastle disease virus infection in chicken.

• Journal of Preventive Medicine and Public Health
• /
• v.21 no.2 s.24
• /
• pp.340-350
• /
• 1988

This study was carried out to clarify the effect of dietary calcium, casein, and suet on the accumulation of cadmium in mice. It was performed for 30 days, from April 11 to May 10 1988.90 mice were divided into 4 experimental groups and control group with 6 mice each dietary group, and measured survival rate, body weight, and weight ratio of organ to body. The contents of cadmium in liver, kidney, spleen, muscle and skin with hair, and feces were analyzed by atomic absorption spectrophotometer after sacrifice by anesthesia. After 30 days, the survival rate of control group was loot,, but 66.7% in group IV(basal diet+Cd+Ca) with single dose of $100{\mu}g$ cadmium and with free-intake of water containing 50ppm cadmium, and group V(basal diet+Cd+suet) with free-intake of water containing 50ppm cadmium. The rate of weight gain in the case of single dose of $100{\mu}g$ cadmium was highest in group IV as 42.3% and lowest in group V as 26.0%, whereas in the cases of free intake group W was highest as 24.0% and group II(basal diet+Cd) was lowest as 11.6%. The body weight, in the case of single dose of $100{\mu}g$ cadmium showed no increase until 5th day after acute poisoning. But in the case of free intake group, it showed very slight increase through all the breeding period. The weight ratio of organ to body were lowest in the liver of group II in both occasions. The most of cadmium adminstered. were excreted through feces within 2 days after single dose of $100{\mu}g$ cadmium. The contents of cadmium in each group were significantly higher than those of control group. In the liver, kidney, spleen and muscle, group II showed the highest level in both occasions of $100{\mu}g$ single dose and free intake of water containing 50ppm cadmium. In the skin with hair, group ll of the occasion with single dose of $100{\mu}g$ and group V with free intake showed the highest level. And the contents of cadmium in tissue were markedly higher in the occasion of free intake of water containing 50ppm cadmium. From the above results I would conclude that the addition of casein and calcium are effective in the inhibition of intesitnal absorption of cadmium esp. by calcium.

• Journal of Sericultural and Entomological Science
• /
• v.2
• /
• pp.1-31
• /
• 1962

The purpose of this treatise is to prove the presence of cystine in silk fiber through wide sampling throughout all the sericultural processes of Bombyx mori.; also to show that disulfide cross linkages exist in the silk fiber. The conclusions reached were as follows: 1. Crystalline cystine was obtained from silk fibroin using Folin's Method. 2. Analytical data showing the cystine content of silk fiber and its related materials were obtained using Sullvan's Method as follows: Material Percent Cystine A. Mulberry leaf protein 0.175 B. Silkworm egg 0.33 C. Silkworm Body, matured, fat extracted, without silk gland 0.41 D. Silk gland, matured 1.23 E. Silkworm feces none F. Silkworm pupa, fat extracted 0.30 G. Silkworm moth, fat extracted 0.60 H. Raw Silk 0.22 I. Fibroin 0.175 J. Sericin 0.30 3. The presence of cystine in the silkworm was substantiated the existence of 0.175 % methionine in mulberry leaves and 0.12% methionine in the silk gland. 4. Part of the sulfhydryl compounds in the silk gland is believed to transfer to serine and methionine, with the former being secreted into the liquid silk finally as silk fiber and the latter used for nutritive purposes in the growing of silk gland tissue. 5. The cystine content is variable by mulberry species, silkworm species, sex, breeding process, and other culturing environments. 6. Hybrid silkworms require more nutritive amino acids for effective growth than the original parents, and secrete less of them as silk fiber. 7. From such an observation, the amino acid composition of silk fiber is believed to be fairly flexible. Cystine if included in the amorphous part of the fiber, especially in sericin. 8. The result from enriching the silkworm diet with pure cystine or wool cystine did not result in any advantage, therefore it is believed that the natural cystine and methionine contents in the mulberry leafaregoodenoughforsilkwormnutrition. 9. The disulfide cross linkage in silk fiber was verified by using the Harris Method. Contraction took place following the treatment of the fiber with various salts and acids. Comparisons were made with wool fiber. 10. During these experiments, the fibrious structure of silk fiber and the net-globular liquid form were photographed microscopically. It is believed that the globules of liquid silk are net-formed by the inter attraction of the OH ion of the globular peptide and the H ion of water as shown by the hair cracking behavior of the film. The net-globular protein precipitation from the mulberry protein solution showed that mulberry is a proper diet for the formation of fibrous protein in the silk fiber. 11. The significance of the presence of cystine in silk fiber as emphasized in this paper should result in modification of the general conception that cystine is absent from this fiber. NOTICE: A part of this treatise was presented at the annual Korea Sericultural Society meeting held in 1961.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.19 no.4
• /
• pp.669-683
• /
• 2017

The objective of this study is to propose a modification of the previously proposed drainage system for catching the partial leakage of underground concrete structures. Two techniques were proposed for applying the drainage system only to the leaking parts. One was for conveying leaking groundwater to the collection point in the drainage system and the other was for conveying the collected groundwater to the primary drainage system of the underground concrete structure. Four waterproofing materials for conveying leaking groundwater to the catchment point of the drainage system, Durkflex made of porous rubber material, KE-45 silicone adhesive with super strong adhesion, Hotty-gel made of polymeric materials and general silicone adhesive were evaluated for waterproofing performance. Hotty-gel only showed perfect waterproof performance and the other three waterproof materials leaked. The modified drainage system with Hotty-gel and drainage pipe with fixed saddle to convey the leaking groundwater from the catchment point to the primary drainage system were tested on the concrete retaining wall. The waterproof performance and the drainage performance were evaluated by injecting 1,000 ml of water in the back of the modified drainage system at the 7-day, 14-day, 21-day, 28-day, 2-month and 3-month. There was no problem in waterproof performance and drainage performance of the modified drainage system during 3 months. In order to evaluate the construction period and construction cost of the modified drainage system, it was compared with the existing leaching repair method in surface cleaning stage, leakage treatment stage, and protective barrier stage. Total construction period and construction cost were compared in considering the contents of work, repair material, construction equipment, working time, and total number of workers. As a result of comparing and analyzing in each construction stage, it was concluded that the modified drainage system could save construction period and construction cost compared to the existing leaching repair method.

• Journal of Korean Society of Forest Science
• /
• v.87 no.2
• /
• pp.230-238
• /
• 1998

This study was conducted to compare the regeneration of the seedlings under different vegetation types and to identify the presence of allelopathy in Abies koreana(Ak) natural forest in Banyabong Peak(elevation, 1715m), of Mt. Chiri. Twenty quadrats($10m{\times}10m$) were placed in May, 1996 to classify vegetation structure using TWINSPAN. Water-soluble extracts from leaves and soil humus of different vegetation types were collected to test their effects on both seed germination of Ak and mycelial growth of ectomycorrhizal fungi. Phenolic compounds from soil humus were quantified using HPLC. Among the four vegetation types, Sasa borealis(Sb) was found in both Ak-Quercus mongolica(Qm) and Ak-Rhododendron schlippenbachii(Rs) communities. Natural seeding of Ak was $230,000{\pm}90,000seeds/ha$ in 1995 and their germination rate was 25% in an ideal laboratory condition. Density of Ak seedlings less than 5cm in height was 52,000/ha in 1996, while that of seedlings taller than 5cm in height was only 4,000/ha. In the case of Ak-Qm community, density of Ak seedlings with Sb understory was only 7% of the density of seedlings with Rs understary, suggesting the inhibitory effect of Sb. The germination rate of Ak seeds was significantly reduced by leaf extracts of Sb, and Rhododendron mucronulatum var. ciliatum(Rm) and Ak. Soil humus extract of Ak-Qm-Sb subcommunity reduced germination of Ak seeds by 81% and also reduced by 19% the respiration of mycelia of ectomycorrhizal fumgus, Lactarius sp. Among the seven phenolic compounds identified from the soil humus, extract, Ak-Qm-Sb subcommunity contained significantly high content of p-hydroxybenzoic acid, vanillic acid, and syringic acid. Particularly, p-hydroxybenzoic acid was present at 4.2ppm in the Sb roots and at 16.5ppm in the Sb humus, suggesting that it could be the primary allelopathic compound in Abies koreana forests with Sasa borealis understory.