• Journal of the Korean Geotechnical Society
• /
• v.38 no.5
• /
• pp.5-17
• /
• 2022

A pile is a type of medium for constructing superstructures in weak geotechnical conditions. A pretensioned spun high-strength concrete (PHC) pile is composed of high-strength concrete with a specified strength greater than 80 MPa. Therefore, it has advantages in resistance to axial and bending moments and quality control and management since it is manufactured in a factory. However, the skin friction of a pile, which accounts for a large portion of the pile bearing capacity, is only approximated using empirical equations or standard penetration test (SPT) N-values. Particularly, there are some poor research results on the pile-soil interface under the seismic loads in Korea. Additionally, some studies do not consider geoenvironmental elements, such as groundwater pH values. This study performs sets of cyclic simple shear tests using submerged concrete specimens for 1 month to consider pH values of groundwater and clay specimens composed of kaolinite to generate a pile-soil interface. 0.2 and 0.4 MPa of normal stress conditions are considered in the case of pH values. The disturbed state concept is employed to express the dynamic behavior of the interface, and the disturbed function parameters are newly suggested. Consequently, the largest disturbance increase under basic conditions is observed, and an early approach to the failure under low normal stress conditions is presented. The disturbance function parameters are also suggested to express this disposition quantitatively.

• Geotechnical Engineering
• /
• v.13 no.3
• /
• pp.63-76
• /
• 1997

To investigate the engineering characteristics of crushed rockfill material, the large-scaled triaxial tests have been carried out, The rpckfill is made from the greywacke, and the 3 parallel gradations with different maximum particle size(dmu=38.1mm, 25.4mm and 19.1mm) were designed for the test. The dimension of the specimen is 300mm in diameter and 600mm in height, and the applied confining stress varied from 5t/$51.6^{\circ}$ to 60t/$51.6^{\circ}$. The test results show that the influence of the maximum particle size on the stress -strain r$51.6^{\circ}\; to\; 40.5^{\circ}$ when the confining stress increases from 5t/$51.6^{\circ}$ to 60t/$51.6^{\circ}$ The hyperbolic parameter values estimated from the test result for rockfill are much different from the recommended values by Duncan et. at(1980) for GW and GP material, especially in the $\phi$ ad K-values.

• Phonetics and Speech Sciences
• /
• v.15 no.1
• /
• pp.25-34
• /
• 2023

This study examined the utility of the acoustic features of vowels as cues for the place of articulation of Korean nasal consonants. In the acoustic analysis, spectral and temporal parameters were measured at the 25%, 50%, and 75% time points in the vowels neighboring nasal consonants in samples extracted from a spontaneous Korean speech corpus. Using these measurements, linear discriminant analyses were performed and classification accuracies for the nasal place of articulation were estimated. The analyses were applied separately for vowels following and preceding a nasal consonant to compare the effects of progressive and regressive coarticulation in terms of place of articulation. The classification accuracies ranged between approximately 50% and 60%, implying that acoustic measurements of vowel intervals alone are not sufficient to predict or classify the place of articulation of adjacent nasal consonants. However, given that these results were obtained for measurements at the temporal midpoint of vowels, where they are expected to be the least influenced by coarticulation, the present results also suggest the potential of utilizing acoustic measurements of vowels to improve the recognition accuracy of nasal place. Moreover, the classification accuracy for nasal place was higher for vowels preceding the nasal sounds, suggesting the possibility of higher anticipatory coarticulation reflecting the nasal place.

• Journal of the Korean Magnetics Society
• /
• v.9 no.4
• /
• pp.190-195
• /
• 1999

The crystallographic and magnetic properties of the system of $Fe_{1-x}Co_x$(x=0.2 and 0.4) prepared by microwave arc-melting with the maximum power of 3.5 kW and a iron-foil with thickness of 25 ${\mu}{\textrm}{m}$ have been studied by the methods of X-ray diffraction and the measurement of the magnetic hysteresis using the vibrating sample magnetometer at room temperature. The samples were prepared in three different ways: First, pellet form pressed under the pressure of 9,000 N/$\textrm{cm}^2$. Second, the sheet cold rolled. Third, thin sheet treated with the temperature of 90$0^{\circ}C$. The X-ray diffraction pattern of the sample prepared by the first method shows that the crystal structure of the sample is bcc as same as that of Fe with a good uniformity. The iron-foil has the coercivity of 43 Oe and the initial slope of magnetization of 0.328 emu/gOe. The coervicity and magnetization of the sample prepared by the second method increased as the Co content increased. But the initial slop of the magnetization decreased as the Co content increased. This means that the displacement of domain wall is suppressed by the increases of coercivity as the Co content increased. The saturation magnetization of the samples made by the third method increased. On the other hand, the coercivity of these samples decreased. The increase of saturation magnetization of the samples seems to be related to the changes in X-ray intensity after heat treatment. Also some magnetic parameters of the samples were calculated by using a simple model and compared with other values.

• Tunnel and Underground Space
• /
• v.24 no.1
• /
• pp.32-45
• /
• 2014

Basic frictional angle is a parameter that can estimate shear strength of rock, and is a design parameter employed in slope stability analysis. Basic frictional angle generates various results in accordance with mineral composition, apart from rock surface roughness itself. This paper describes the correlation of basic frictional angle and mineral composition. The basic frictional angle is measured with the aid of the modified tilt testing apparatus, and its reliability is improved by the statistical method. Also, mineral composition is identified through the photographic analysis on rock specimen, and verified through the thin section analysis.

• Polymer(Korea)
• /
• v.29 no.5
• /
• pp.508-517
• /
• 2005

The thermal degradation behavior and reliability analysis were investigated using dynamic thermogravimetric analysis (TGA) and accelerated degradation test (ADT) to characterize the dynamic parameters related to thermal degradation of plastic meterials for household electric appliances. In addition, the weathering of the plastic were performed by ADT using Xenon uc, and the color difference of the samples after ADT were measured with Color Eye 3010 specoophotometer. he activation energy for thermal degradation of the samples increased with increasing the rate of weight loss. The Kim-Park method was found to be more effective analysis in describing thermal degradation of plastic meterials. Plastic materials were very sensitive to ultra-violet rays in faster degradation.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2022.05a
• /
• pp.432-432
• /
• 2022

하천의 하상재료는 토양 유실량 및 유사량 산정, 유사이송, 하상변동, 하천환경 등 여러 분야에 영향을 미친다. 하상재료는 강수 및 유량 등 여러특성들의 상호작용으로 인해 지속적으로 변화하며, 하천 분야의 각종 해석 및 영향 평가 등에 이용되는 활용성을 감안하여 하상재료는 체계적인 관리시스템이 필요하다고 판단된다. 효율적인 하상재료 관리를 위하여 한국수자원조사기술에서 수행한 하천유역조사, 유사량조사, 하도변화 모니터링 사업을 통해 수집된 자료를 활용하였다. 국내 109개 하천(한강권역 39개 하천, 낙동강권역 23개 하천, 금강 34개 하천, 섬진강 5개 하천, 영산강 8개 하천)에 대한 자료를 수집하고 분석하여 하상재료관리시스템(Bed Material Management System, BMMS)을 구축하였다. BMMS는 GIS 기반으로 구축된 시스템으로 관리, 표출 및 분석이 가능하며 하상재료의 위치정보, 하상재료 성분비 및 유효경 등 총 11개로 구성되어 있다. 하상재료조사는 시료채취 방법과 표층조사 방법으로 조사하였으며, 시료채취는 체가름 시험과 비중 시험을 이용하였고 표층조사는 BASEGRAIN 프로그램을 이용한 표층 영상분석을 통해 입도분포, 입경가적곡선 등을 나타내었다. 향후 이용자의 편의성을 위한 방안을 모색 중에 있으며, 하천별 하상재료 분석자료를 정기적으로 축척하여 국내 하천의 지역적 특성을 고려한 매개변수 산정 및 최적화에 도움이 될 것이라 판단된다.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.14 no.5
• /
• pp.1229-1241
• /
• 1994

This study aims at investigating the undrained behavior of the normally consolidated clay foundation using single hardening constitutive model based on elasticity and plasticity theories. The specimen employed was sampled at Mooan near the down stream of Young San river and remolded into consolidation apparatus. 11 soil parameters for the model was determined from simple tests such as isotropic compression and consolidation undrained triaxial compression tests. FEM program to predict the undrained behavior of the foundation was developed and back analysis was performed to verify prediction ability of the FEM program. Finally plate load test on the 2-dimensional model foundation was carried out in order to compare numerical analysis and observed values on the foundation.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.8 no.4
• /
• pp.821-825
• /
• 2007

In this study, the single hardening model with stress history-dependent plastic potential, which has been most recently proposed based on the critical state soil mechanics and needs few model parameters, was verified for the normally, lightly, and heavily over-consolidated clayey specimens. The triaxial compression tests were strictly conducted. The predictions using the single hardening model generally agree with the measurement. The discrepancy exists on its main focusing on the principal stress rotation; however, the plastic work H and the principal stress rotation angle ${\beta}$ are found to be effective indicators of loading history for the plastic potential function of the stress path dependent materials.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.14 no.1
• /
• pp.195-202
• /
• 1994

In this research, a lot of triaxial test results (CID) are analyzed to study the curvature characteristics of failure envelope of sand and parametric relationship between shear strength and state parameter by Been and Jefferies. In the conventional triaxial tests, correction for the change of sectional area of a sample and for membrane influence is essential especially in order to determine critical state (or steady state) condition more correctly. Based on the test results, a model to express the shear strength of fine sand as a function of density and stress level is presented and curvature characteristics of shear failure envelope and parametric relationship between state parameter and shear strength parameters are evaluated.