• Transactions of the Korean Society of Automotive Engineers
• /
• v.16 no.4
• /
• pp.97-102
• /
• 2008

The vibration of a vehicle, which is caused by and transmitted from the engine, has significant effect on the ride comfort and the dynamic characteristics of the engine mount system have direct influence on the vibration and noise of the vehicle. This paper examines the body shake caused by the engine excitation force on engine key on/off of a medium truck by experiment and simulation. The analysis model consists of the engine, a body including the frame, front and rear suspensions and tires. The force element between the body and the suspension is modeled as a combination of a suspension spring and a damper. The engine shake obtained from the experiment was compared with the result of the computer simulation, and by using the verified computer model, parametric study of the body shake on engine key on/off is performed with changing the stiffness of an engine mount rubber, the engine mount angle, and the position of engine mounts.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.772-776
• /
• 2011

EAV-2, which has a solar cell, fuel cell and battery as its power sources, is under development by KARI. Electric power sources are selected through voltage matching without power converter and controller and tested. The ground integrated test for integrated system is performed during 5 hr. it is confirmed that battery's power response is faster than other power sources at starting and transient condition, fuel cell and solar cell are a major electrical power during cruise condition. It is revealed that the used energy portions of fuel cell, solar cell and battery are 68%, 29%, 2.5% respectively.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1998.10a
• /
• pp.39-39
• /
• 1998

본 연구는 500KW급 수평축 풍력발전기용으로 개발된 회전날개의 시제품 제작에 앞서 축소모델에 대한, 이론적으로 예측된 공력성능과 신축에 의한 공력성능을 비교 검토함으로서, 설계결과를 검증하고, 필요한 경우 설계를 보완하여 개발위험도를 최소화하기 위해 수행되었다. 시험모델의 크기는 실제의 5%로서 직경이 2.1m이며 날개의 시위길이는 0.2r/R에서 0.101m, 날개끝에서 0.043m 이고, 날개단면형 상온 FX-S-03-182이다. 블레이드의 재질은 Glass/Epoxy 복합재료로 제작되었으며, 실제 풍황을 모사하기 위해 자연풍 상태에서 실험하였다. 실험장치의 구성은 15m 높이의 타워에 회전날개와 전자브레이크 및 각종 센서를 장착하였고, 날개가 회전하기 시작하면 제동장치에 의해 부하를 주면서 토크, 회전수, 풍속 등을 각각의 센서로부터 자료획득장치를 통해 자료처리를 할 수 있도록 하였다. 실험하는 동안 풍속은 4m/s-13m/s 정도로서 시동 풍속인 4m/s와 정격풍속인 12m/s를 포함하여 회전날개의 전체적인 특성을 파악하기 용이하였고, 이론적인 예측성능과 측정된 성능을 비교 검토한 결과 비슷한 결과를 얻어 공력설계 및 해석 방법을 검증하였다.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.52 no.3
• /
• pp.107-115
• /
• 2003

This paper deals with the effect of the auxiliary pole core in the automotive starter motor on its characteristics. This motor is excited by the permanent magnet and has auxiliary pole core in the stator. The auxiliary pole core is a device to increase the effective flux to obtain the starling torque and prevent the demagnetization of the permanent magnet from the starting current. It Is important to design the auxiliary pore core. And overhang structure causes the electromagnetic phenomenon of 3-dimensional flux Path. Therefore. the characteristic analysis is achieved by the 2-dimensional Finite Element Method (FEM) with the compensated model and the 3-dimensional Equivalent Magnet Circuit Network (3D EMCN). The mechanical loss and the brush and coil resistance are separated from the various experiment of the tested motor, and then these factor are reflected on the analysis results. The validity of the proposed analysis method is verified by comparing the experimental and analysis results. The effects of the design parameters related to the auxiliary pole cote on the motor performance are analyzed by the proposed method.

• Journal of the Korean Ceramic Society
• /
• v.42 no.10 s.281
• /
• pp.672-677
• /
• 2005

In this study we prepared the Sr-ferrite powders and magnet by a molten salt method using the (NaCl+KCl) salt mixture. Starting materials of $Fe_{2}$$O_{3}$ and Sr$Co_{3}$ were mixed as the molar ratio of 5.70:1, and 0.08 mol$ \% $ $Al_{2}$$O_{3}$, 0.10 mo1$ \% $ Si$O_{2}$ and 0.12 mo1$ \% $ CaO were added as additives. Sr-ferrite powders synthesized at the reaction temperatures of 800$\∼$1200$ ^{\circ}C $ showed the typical M-type hexagonal ferrite phase, and hexagonal plate-like morphology with uniform distribution of 1$\∼$3 $\mu$m particle size. The bulk density of the sintered Sr-ferrite magnet prepared with powders by the molten salt method showed the maximum density of 4.82 g/$cm^{3}$ at the sintering temperature of 1200$^{\circ}C $. The maxima of remanent flux density (Br, 45 emu/g) and coercive force (iHc, 3.75 kOe) occurred at the sintering temperatures of 1150$ ^{\circ}C$ and 1200$^{\circ}C $.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.31 no.3 s.258
• /
• pp.234-241
• /
• 2007

The regulations for hydrocarbon emission from vehicles have become much more stringent in recent years. These more stringent regulations request vehicle manufacturers to develop the advanced exhaust system for reducing exhaust emissions. The exhaust emissions has many sources in vehicle. In order to investigate the characteristics of hydrocarbon(HC) in the exhaust manifold, concentrations of individual HC species were measured in exhaust process. Using sampling valve, the light hydrocarbon emissions were captured in the exhaust manifold(catalyst before and after) and analyzed from LPLi engine exhaust manifold(catalyst before and after) using different fuel properties. Then exhaust samples were measured by gas chromatography(GC) and exhaust gas analyzer. Catalyst conversion efficiency for fuel properties of Butane 100% was better than Propane 100%. Start delay of LPLi engine was observed as increment of propane contents in LPG fuels.

• Journal of the korean Society of Automotive Engineers
• /
• v.9 no.2
• /
• pp.1-4
• /
• 1987

내연기관 연구에 전념하는 모든 사람들의 한결같은 3대 염원은 연비향상, 비출력증대 및 유해 배기가스 성분 감소이다. 이중 비과급 가솔린 기관의 경우 비출력 증대를 위한 4-stroke cycle 엔진에서의 여구는 현지까지 헤아릴 수 없이 많은 연구가 진행되어 발전의 한계에 도달한 느낌 이다. 따라서 이의 실질적인 증대는 시각을 달리하여 2-stroke cycle로의 전환으로서만 가능하리 라 본다. 2-stroke 엔진은 원래 이목적으로 고안된 것이라는 것은 주지의 사실이다. 그러나 이 장치가 비출력면에서 효과적인 가솔린엔진의 경우에서도 현재까지 별로 각광을 받지 못한 것은 다음과 같은 몇가지 두드러진 이유 때문이라고 본다. 첫째 흡입연료의 일부가 소기(scavenging) 과정에서 배기공으로 곧바로 유출됨으로 배기 공해성분을 증가시키고 연료손실에 따른 연비저감 을 초래하는 것이다. 둘째로 crankcase 소기를 이용하는 소형가솔린 2-stroke 엔진에서는 새 공 기의 흡입이 충분치 못하여 일방적으로 높지 않은 소기효율을 고려한 최종 흡입 체적효율은 상당 히 낮아지게 됨으로써 목적하는바의 비출력 증대의 득을 별로 얻지 못함은 물론 잔류가스율이 높아 저부하, 저속도에서 엔진의 구동이 손조롭지 못ㅎ하고 시동이 어려워지는 특성을 나타나게 된다. 따라서 이러한 바람직하지 못한 결과를 감수할 수 있는 경우에는 소형원동기에 주로 2-stroke 가솔린 엔진이 이용되어 왔다. 요사이 이러한 약점들을 타개할 수 있는 고안들이 미국 SAE지에 소개되어 관심을 끌고 있어 이에 대해 요저먹으로 소개하고자 한다.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.2
• /
• pp.8-15
• /
• 2003

During cold operation, fuel injection in the intake port directly contributes to the unburned hydrocarbon formation in spark ignition engines. The relationship between injection parameters and HC emission behavior was investigated through a series of experiments. Spray behavior of port fuel injectors was characterized through a quantitative evaluation of mass concentration of liquid fuel by a patternator and PDA(Phase-Doppler. Anemometer). A 6-hole injector was found to produce finer spray than single hole injector. Using a purpose-built wall, the wetted fuel was measured, which was mostly affected by wall temperature. HC emissions were measured in a production engine varying coolant temperature$(20~80^{\circ}C)$, also with respect to the different types of injectors. In the 6-hole injector application, the engine produced less HC emission in low coolant temperature region. Though it produces much more amount of wetting fuel, it has the advantages of finer atomization quality. In high coolant temperature region, there was little effect by different types of injectors. The control schemes to reduce HC emissions during cold start could be suggested from the findings that the amount of fuel supply and HC emission could be reduced by utilizing fine spray and high intake wall temperature.

• Journal of Sensor Science and Technology
• /
• v.24 no.3
• /
• pp.208-213
• /
• 2015

The purpose of this study is to optimize the design of a capacitive pressure sensor element using the simulation of electrical characteristics. The simulation of the ceramic sensor diaphragm ($Al_2O_3$) was performed by permitting pressure to change the curvature of the diaphragm. The pressure capacitance ($C_P$) was increased from 19.63 pF to 15.26 pF by applying pressure because the distance between the electrodes has been changed from $30{\mu}m$ to $15{\mu}m$. When the thickness of the diaphragm was changed to 0.46~0.52 mm, a larger capacitance change showed in accordance with the reduced thickness, which means an increase of sensitivity. However, considering the viewpoint of the signal linearity, it was selected for the optimum thickness of the diaphragm to 0.50 mm. The designed sensor element based on simulated results was tested to measure the output characteristics. Comparing of simulated and measured results, there was a margin of error of approximately 2%.

• Proceedings of the SAREK Conference
• /
• 2005.11a
• /
• pp.311-316
• /
• 2005

The experimental study for an operational characteristics and performance of the sodium heat pipe were carried out. For an experiment. the heat pipe which is 1000mm length and 25.4mm diameter of stainless steel container with 50 mesh of screen wick using sodium as a working fluid is manufactured and tested as functions of heat flow rate, inclined angle and operating temperature. The test results are as follows. During the start-up. frontal start up was observed because of the vapor density increasing as increased the hot zone. Also, the heat pipe showed uniform temperature over than $420^{\circ}C$ of the operating temperature. The average heat transfer coefficient increased as the heat flux and the vapor temperature increase, and the range of the total thermal resistance was 0.075-0.04 $^{\circ}C/W$ at the 12-53.55 $kW/m^2$ of heat flux and $500-750^{\circ}C$of operating temperature. The maximum heat flow rate was 750W at the 10 degree of top heating mode.