• Journal of Advanced Navigation Technology
• /
• v.24 no.2
• /
• pp.101-106
• /
• 2020

In order to smoothly control the speed of the induction motor, it is necessary to obtain the required rotor speed information. In order to obtain the speed information, it must be obtained using a sensor, but it can also be obtained using an appropriate algorithm without using a sensor. In order to obtain speed information, a system was designed using a model reference adaptive system (MARS). Indirect vector control, one of the speed control methods of induction motors, was calculated from the motor current and rotor parameter values. The method of obtaining the position information of the magnetic flux by combining the slip frequency with the rotor speed was used. It is possible to simply perform instantaneous current control in a wide speed range without actual magnetic flux information, and has the advantage that the structure of the controller is simple. Therefore, in this paper, the control system was constructed based on the indirect vector control method, and the speed control system of the induction motor was developed by estimating the required rotor speed information as an intelligent algorithm developed without using it as a sensor.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.5
• /
• pp.1123-1131
• /
• 1993

A robust controller is proposed to design a flight autopilot for lateral motion control. The control system has two control loops in order to meet the performance and to maintain the stability-robustness for a nonsquare flight system with uncertain aerodynamic variations and disturbance. One is designed via linear quadratic Gaussian with loop transfer recovery(LQG/LTR) design methodology for the inner loop. The other is designed via proportional controller design method for the outer loop. To show the effectiveness of this control system, it is compared with the LQG/LTR control system for a square flight system and is analyzed for the performance/stability-robustness to model uncertainties and disturbance via wind gusts. It is found that the proposed control system has good heading command-following performance under allowable sideslip angle in spite of model uncertainties and disturbance.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.11a
• /
• pp.230-236
• /
• 2008

In this paper, a model-based stick-slip compensation for the micro-positioning is proposed using an enhanced stick-slip model based on statistical rough surface contact model. The smart structure is comprised with PZT (lead (Pb) zirconia (Zr) Titanate (Ti)) based stack actuator incorporating with the PID (Proportional-Integral-Derivative) control algorithm, mechanical displacement amplifier and positioning devices. For the stick-slip compensation, the elastic-plastic static friction model is used considering the elastic-plastic asperity contact in the rough surfaces statistically. Mathematical model of system for the positioning apparatus was derived from the dynamic behaviors of structural parts. PID feedback control algorithms with the developed stick-slip model as well as feedforward friction compensator are formulated for achieving the accurate positioning performance. Experimental results are provided to show the performances of friction control using the developed positioning apparatus.

• Journal of Institute of Control, Robotics and Systems
• /
• v.16 no.12
• /
• pp.1212-1219
• /
• 2010

The most important thing in the container terminal is to handle the cargo effectively in the limited time. To achieve this object, many strategies have been introduced and applied to. If we consider the technical trends and environment of the automated container terminal, it is necessary that the systems for cargo handling are equipped with more intelligent control technologies. To cope with this tendency, from the middle of the 1990's, the automated RMGC (Rail-Mounted Gantry Crane) and RTGC (Rubber-Tired Gantry Crane) have been developed and widely used to handle containers in the yards. Recently, in these cranes, the many equipments like CCD cameras and sensors are mounted to cope with the automated terminal environment. If we want to obtain more efficient handling performance, the modelling, tracking control, anti-sway system design, skew motion suppressing and complicated motion control problems must be considered in the control system design and application process. Considering these problems, in this paper, the system modelling with the tire slip and a tracking control approach are proposed. Especially, we design the tracking control system based on the 2DOF servosystem design approach to cope with undesirable disturbance input. The experiment results show the desirable performance and usefulness of the designed control system.

• Journal of Institute of Control, Robotics and Systems
• /
• v.15 no.2
• /
• pp.184-191
• /
• 2009

The common requirements of rough terrain mobile robots are long-term operation and high mobility in rough terrain to perform difficult tasks. In rough terrain, excessive wheel slip could cause an increase in the amount of dissipated energy at the contact point between the wheel and ground or, even more seriously, the robot could lose all mobility and become trapped. This paper proposes a traction control algorithm that can be independently implemented to each wheel without requiring extra sensors and devices compared with standard velocity control methods. The proposed traction algorithm is analogous to the stick-slip friction mechanism. The algorithm estimates the slippage of wheels by angular acceleration change, and controls the increase or decrease state of torque applied to wheels Simulations are performed to validate the algorithm. The proposed traction control algorithm yielded a 65.4% reduction of total slip distance and 70.6% reduction of power consumption compared with the standard velocity control method.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.8 s.227
• /
• pp.1075-1086
• /
• 2004

In this paper, Time Delay Control(TDC) for robot manipulators is analyzed and its problems are founded. In order to remedy the problems, the enhanced controller is proposed and analyzed. The effect of friction associated with TDC is reported and its cause is presented. Through the analysis, simulation and experiment, it is shown that the friction effect causes serious degradation in control performance and that it is a result of the error of Time Delay Estimation(TDE) in TDC. In order to remedy the problems, TDC combined with Internal Model Control(IMC) concept is proposed. The proposed compensator is effective enough to handle the bad effect of friction, and is so simple and efficient as to match positive attribute of TDC. The simulation and experimental results show the effectiveness of proposed controller against the friction of the robot manipulators.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.18 no.11
• /
• pp.1134-1142
• /
• 2008

In this paper, a model-based stick-slip compensation for the micro-positioning is proposed using an enhanced stick-slip model based on statistical rough surface contact model. The smart structure is comprised with PZT(lead (Pb) zirconia(Zr) Titanate(Ti)) based stack actuator incorporating with the PID(proportional-integral-derivative) control algorithm, mechanical displacement amplifier and positioning devices. For the stick-slip compensation, the elastic-plastic static friction model is used considering the elastic-plastic asperity contact in the rough surfaces statistically. Mathematical model of system for the positioning apparatus was derived from the dynamic behaviors of structural parts. PID feedback control algorithms with the developed stick-slip model as well as feedforward friction compensator are formulated for achieving the accurate positioning performance. Experimental results are provided to show the performances of friction control using the developed positioning apparatus.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.6 no.1
• /
• pp.57-63
• /
• 2001

The wound rotor type induction motor(WRIM) control system which is widely used in the industry has many maintenance problem because of external resistors and magnetic contactors. In this paper, the simple sensorless vector control algorithm for WRIM is proposed without any additional devices except detecting rotor currents. Because the external resistors are disconnectd and the rotor slip rings are shorten, the power loss due to external resistors is removed and the maintenance problem is improved remarkably. Also, the vector control performance becomes better because the proposed sensorless vector control algorithm does not use the rotor resistance which is usually used to estimate the slip frequency in case of indirect vector control scheme. The proposed algorithm is verified by the digital simulation and the experiment.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.18 no.5
• /
• pp.74-82
• /
• 2004

This paper describes the speed control of the surface-mounted permanent-magent synchronous motors (SMPMSNM) for elevator drive. The elevator motor needs to be a compact and slim type. Essentially, the proposed scheme uses a vector control algorithm for a speed and torque control and Anti-windup technique is adopted to prevent a windup phenomenon. This system is implemented using a high speed 32-bit DSP (TMS320C31-50), a high-integrated logic device FPGA(EPF10K10TI144-3) to design compactly and inexpensively. The proposed scheme is verified by the results through digital simulation and experiments for a three-phase 13.3[kW] SMPMSM as a MRL(MachineRoomLess) elevator motor in the laboratory.

• Journal of the Institute of Electronics Engineers of Korea CI
• /
• v.48 no.6
• /
• pp.9-16
• /
• 2011

Due to the development and proliferation of ubiquitous technologies and services, various sensor network applications are being appeared on the stage. The needs for algorithms requiring sensor data fusion and complex signal processing with a high-performance processor such as a digital signal processor are also increased. However, it is difficult to use such processor for the low-power sensor network operating with a battery because of power consumption. This paper proposes a hybrid-type sensor module architecture supporting wakeup/sleep software framework for the wireless sensor node and shows the implemented sensor node platform and performances focused on the energy consumption and wakeup time.