• Journal of the Korean Ceramic Society
• /
• v.34 no.1
• /
• pp.70-78
• /
• 1997

3Y-TZP/SUS316 Functionally Graded Material (FGM) was fabricated by slip casting method. Alumina mold was used to overcome problems of gypsum mold in slip casting process, and the optimal dispersion con-ditions of 3Y-TZP/SUS316 binary slurries was determined using electrokinetic sonic amplitude and a viscometer, and observing sedimentation behavior. The properties of the specimens casted by gypsum mold and alumina mold were compared in terms of changes in shrinkage rate, drying and sintering conditions, and microstructure. It was found that the specimens obtaine from the alumina mold showed a clean surface, easier thickness control of each layer, and higher productivity. Especially, no degradation was observed in the SUS316 prepared using alumina mold. Thus it is desirable to use porous alumina mold rather than gyp-sum mold for the slip casting of 3Y-TZP/SUS316-FGM.

• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.643-648
• /
• 2011

Fatigue crack in most rails take place by rolling contact between wheel and rail in railway industry. Therefore, it is critical to understand the rolling contact phenomena, especially for the three-dimensional situation. In this paper the steady-state rolling contact problem of KTX wheel and rail (UIC60) has been studied with three-dimensional finite element analysis. The variation of contact pressure and contact stresses on rolling contact surface were obtained using the finite element method. The three-dimensional distribution of contact stresses on the contact surface are investigated. Results show that the distribution of shear stress and contact stress (von Mises) on the contact surface varies rapidly as a result of the variation of stick-slip region. The contact stress at the leading edge is greater than at the trailing edge because of stick and slip phenomena.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1992.10a
• /
• pp.177-181
• /
• 1992

For this study, a new hydraulic control unit which designed in compact compared to the currently manufactured hydraulic control unit for ABS has been introduced and its experimental model has been made. Based on the basic principle as ABS using braking force characteristics against slip ratio of tire, half car model bench tester were designed and made to make an analysis of braking effect of the new hydraulic control unit. Experiment for slip ratio characteristics of tire has been carried out using half car model bench tester and with the results of this experiment and control experiment of the new hyraulic control unit, the experiment result of the characteristics of tire and control experiment were compared to find out their correspondence. And furthermore, slip ratio characteristics of the new hydraulic control unit has been studied based on the experiment result of slip ratio characteristics of tire through simulation and compared with experiment result.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.1
• /
• pp.78-85
• /
• 2013

This paper presents the sliding mode control methods for anti-lock brake system (ABS) with the friction force observer. Using a simplified quarter car model, the sliding mode controller for ABS is designed to track the desired wheel slip ratio. Here, new method to find the desired wheel slip ratio which produces the maximum friction force between road and tire is suggested. The desired wheel slip ratio is varying according road and tire conditions to produce maximum friction force. In order to find optimum desired wheel slip ratio, the sliding mode observer for friction force is used. The proposed sliding mode controller with observer is evaluated in simulation, and the control design is shown to have high performance on roads with constant and varying adhesion coefficients.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.33 no.12
• /
• pp.61-67
• /
• 2005

This paper presents the carrier phase DGPS method providing a stable navigation solution under the condition of frequent blockage of the GPS signals. The proposed algorithm reject the channels having large errors using a clock bias drift and then calculated the more accurate solution. By investigating the relation between visible satellites` elevation and their clock bias drift, a proper threshold is set. Simulation shows that the presented result is as good as that of commercial system with real data.

• Proceedings of the KIEE Conference
• /
• 2004.07d
• /
• pp.2320-2322
• /
• 2004

전자제어식 미끄럼방지 제동장치 (ABS, Antilock Brake System)는 차량의 급제동시 발생할 수 있는 바퀴의 슬립을 방지하여 차량의 제동거리를 단축시키고 주행 성능을 향상시키는 차량 내 안전장치이다. 지난 몇 년 동안 공압식 제동시스템을 사용하는 대형차량에 적합한 미끄럼방지 제동 제어기를 연구해 왔다. 이 제어기는 바퀴의 슬립율과 그 변화량을 이용한 제어 법칙을 유도하여, 제어 파라미터로 사용하고 있다. 이러한 제어 파라미터의 튜닝에는 맡은 반복적인 실험이 요구된다. 이러한 요구에 부응하기 위하여 차량의 제동을 실시간으로 모사 할 수 있는 HILS (Hardware In-the Loop Simulation) 시스템을 개발, 구축하였다. 개발 HILS는 공압식 브레이크 시스템 및 14 자유도를 가지는 차량 동역학 모델 및 타이어-바퀴 동역학을 소프트웨어 모델로 사용하고, 개발 중인 전자제어식 미끄럼 방지 제동 제어기를 하드웨어로 사용하여, 바퀴속도 센서 신호 모의 장치 및 공압 엑추에이터 모의 신호등의 인터페이스 장치를 사용하여 제동중인 차량의 상태를 실시간으로 시뮬레이션 및 감시할 수 있다. 이 개발 HILS를 이용하여 제동 제어기의 제어 파라미터의 튜닝을 짧은 시간에 성공적으로 끝낼 수 있었을 뿐만 아니라, HILS 실험을 마친 제어기는 미끄럼 방지 제동 시험장에서 실차 주행 시험을 무사히 마침으로써, 개발 기간과 비용을 절감할 수 있는 하드웨어를 이용하는 시뮬레이션의 효용성을 간접적으로 증명하였다.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.5
• /
• pp.134-141
• /
• 2005

Semi-Spherical Continuously Variable Transmission(SS-CVT) is the CVT which transmits power by rolling friction between dry metals, and its outstanding advantage is the ability of realizations of neutral, forward and reverse states without relying on any other devices. A spherical shaped variator transmits power and also changes gear ratio where keeping contact with a output disk. The frictional direction to transmit power and the other direction to change gear ratio are perpendicular to each other, so we can describe that two dimensional rolling friction is occurred in the contact point between the variator and the disk. Since magnitudes or relations of the two forces are completely unknown, they were analyzed by the experiments in this study. We determined the variables related with the friction phenomena by the dimensional analysis, and manufactured the SS-CVT test bench which could measure the related variables. Finally, the empirical formula for evaluating the two friction forces was proposed based on the experimental results.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1991.04a
• /
• pp.68-76
• /
• 1991

최근 열간압연의 공정이 단순하고 회수율이높은 CC재 (연속 주조재)가 IC재 (Ingot 주조재)에 비해 냉간압연 재료의 주종을 이루고있으며, Roll 조도의 급속한 저하로 슬립현상과 채터링현상 등이 발생한다. 본 연구에서는 Work Roll 마멸 및 조도 저하에 큰 영향을 미치는 (1) 압연 가공길이 및 (2) 실험 재료의 종류에 따른 영향과 (3) 압연하중에 의한 Roll 조도변화를 실제 압연가공을 통하여 분석하고, (4) 알미늄 산화 게재물의 영향과 전사율을 연구하고저 한다.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.03a
• /
• pp.25-25
• /
• 2003

마그네슘 합금은 결정구조가 HCP구조로 슬립면이 제한되어있어 상온에서의 가공이 용이하지 않다. 따라서 최근 마그네슘 합금의 미세 조직을 제어하기 위해 많은 연구가 수행되어 왔다. 본 연구에서는 구조용 재료 및 기능성 재료로 기대되는 마그네슘 합금(AZ3l)을 이용하여 주조로부터 압출·압연 과정으로의 연속적인 판재 성형공정을 실행하였다. 모든 공정에 대한 전형적인 기계적 특성을 평가하기 위하여 각 공정에서 재료의 인장실험을 실시하였으며 각 공정 후에 향상된 기계적 특성들을 규명하기 위하여 경도시험을 실시하였다 또한 각 공정에서의 대표적인 미세 조직을 관찰하여 결정립 미세화에 따른 기계적 물성의 향상을 확인하였다. 주조재, 압출판재, 압연판재의 인장강도는 189.3㎫, 257.9㎫ 그리고 234.㎫로 증가하였다가 다소 감소하지만, 연신율은 상대적으로 16.26%, 24.99% 그리고 27.16%의 50%에 가까운 주목할만한 증가를 나타낸다. 인장실험의 실험결과로부터 얻어진 가공경화지수로부터 대상 재료인 마그네슘 합금(AZ3l)에 대하여 DRX의 거동을 예측할 수 있었으며, 압출후 압연 판재의 경우 연한 재결정 조직으로 인하여 연신율의 대폭적인 증가를 확인 할 수 있었다.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.4 no.4
• /
• pp.357-367
• /
• 1999

When traction system of 2-motor driven electric vehicle(EV) is consisted of two motors (IPMSM) . two inverters. and one traction controller, control performances of IPMSM for an electric vehicle is affected by parameter variation b because of large current magnitude and wide current phase angle. To solve this problem, new parameter estimator for L Ld and Lq is constructed by neu때 network technique. And new vector control algorithm with parameter estimator by n neural network is proposed for IPMSM.And also. an advanced traction control algorithm is proposed using fuzzy c controller in order to enhance the driveability oftwo-wheel drive EVs with fitted with a traction control system Performances of the proposed algorithm are examined by simulations and the experimental resul않 with respect to t the prototype IPMSM and EV.