• Journal of IKEEE
• /
• v.13 no.3
• /
• pp.72-79
• /
• 2009

This paper describes a compact microstrip active antenna with dual polarization. The antenna, receiving both a left-hand circularly polarized wave and a right-hand circularly polarized wave, has a function of polarization diversity. A square-shaped empty room is located on the inside of the microstrip radiator so that the size has been reduced. And slots are added around feeding point to improve input matching. Also, amplifier and switching circuitry are placed at the empty room to increase antenna gain and to select one of the circular polarizations, respectively. The proposed antenna has been applied to GPS(global positioning system). The measurement results show that it has 10dB-impedance bandwidth, 3dB axial bandwidth of about 50MHz, 3dB beamwidth of 90degree, and gain of 13dBi, respectively, for RHCP. Also, it has 3dB axial bandwidth of about 50MHz, 3dB beamwidth of 84 degree, and gain of 12dBi, respectively, for LHCP.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.6 no.5
• /
• pp.629-636
• /
• 2011

This paper presents the design of a novel integrated T-DMB/GPS/Mobile antenna for vehicular application. The T-DMB antenna is designed with a modified meander-type microstrip patch providing linearly a polarized broadside radiation pattern. The GPS antenna is designed with an inserted slot in the patch antenna providing circularly polarized broadside radiation pattern. The Mobile (GSM, AMPS, DCS, PCS, UMTS, etc.) antenna is designed as a modified G-type patch antenna providing multi-band operation. Experimental results indicate that the impedance bandwidth (VSWR 1:2.5) of the proposed T-DMB /GPS/Mobile antenna satisfactorily matches that of the simulation results. The 2D and 3D radiation patterns and gains according to the results of the experiment are also presented and discussed.

• Journal of Advanced Navigation Technology
• /
• v.22 no.6
• /
• pp.665-669
• /
• 2018

In this paper, we design an antenna for LTE / Wi-Fi communication that operates in 2.65 GHz and 5 GHz band for small-sized broadband communication antenna that can be used in the sea. Microstrip patch antennas were chosen to improve the bandwidth. The slot width, length, and transmission line width were calculated using the theoretical formula for each step. In addition, we designed a microstrip antenna using CST Microwave Studio 2014 program that can design 3D. Simulation results show that the reflection lossis -12.712 dB at 2.65 GHz and -16.583 dB at 5 GHz. The gain was 1.738 dBi at 2.65 GHz and 3.284 dBi at 5 GHz. In this paper, we propose a dual-band antenna for LTE / Wi-Fi, which can be used in maritime environments, which is worse than terrestrial communication, because of differences in communication speed and communication stability compared with those used on land.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.24 no.7
• /
• pp.960-966
• /
• 2018

Communication antennas used at sea have been developed remarkably. However, the speed of this development is insufficient when compared with user demands. Therefore, we developed an antenna for UWB/Bluetooth that operates on 3 [GHz] and 5.72 [GHz] bands in order to use the high-speed communication network system which improved antenna miniaturization, gain and radiation patterns. To improve bandwidth, a microstrip patch antenna was selected and CST Microwave Studio 2014 program was used. Through the program, we calculated the slot width, length, transmission line width, etc. using a theoretical formula at each step. These figures were checked through simulation to see if they meet production standards. UWB for high-speed wireless communication for short-range communication at sea, Bluetooth for exchanging information at a short distance by connecting each device, and corresponding technology can be easily utilized.

• Journal of IKEEE
• /
• v.27 no.4
• /
• pp.405-410
• /
• 2023

This paper presents a novel method of implementing a dual-band antenna using a square patch with an inset feed structure. The proposed method is to simply design a dual-band antenna using an asymmetric inset structure with different lengths of slots dug into the patch for inset feeding. To verify the proposed method, a dual-band inset patch antenna supporting 1.57 GHz GPS and 2.4 GHz WiFi bands was designed and manufactured on a 1 mm thick FR4 substrate. From measurement, it was confirmed that the frequency bands of the antenna that satisfy a return loss of -10dB or less are 1.55~1.57GHz and 2.41~2.45GHz, which has dual-band characteristics. Using the proposed method, it is possible to simply implement a dual-band antenna using inset feeding, and it is expected to be utilized in a variety of application fields.

• Journal of Advanced Navigation Technology
• /
• v.28 no.3
• /
• pp.356-361
• /
• 2024

This paper deals with the design and fabrication of a coplanar waveguide (CPW)-fed super-wideband semicircular-disk-shaped dipole antenna operating in a frequency band of 2.4 GHz or higher. To feed the antenna, a CPW feed line was appended to the center of the lower arm of the semicircular-disk-shaped dipole antenna. For miniaturization, square patches were added to the ends of the two arms of the semicircular-disk-shaped dipole, whereas the slot width of the CPW feed line at the center of the dipole antenna was increased to improve impedance matching in the 5.4-6.3 GHz band. The simulated frequency band of the proposed antenna for a voltage standing wave ratio (VSWR) less than 2 was 2.369-30 GHz(170.7%), whereas the fabricated antenna was maintained VSWR less than 2 in the frequency range of 2.378-20 GHz when measured using a network analyzer operating up to 20 GHz so it can be applied as a super-wideband antenna for next-generation mobile communications.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.9
• /
• pp.912-918
• /
• 2003

In this paper, we designed and implemented the dual band monopole antenna for cellular CDMA(Code Division Multiple Access) and IMT-2000(International Mobile Telecommunication 2000) repeater. The antenna was designed by using 3D simulations program, HFSS(High Frequency Structure Simulator). Electrical characteristics were measured by using HP 8720C network analyzer and measured maximum S$\_$11/ was -10.9 dB for all frequency bands of interests in Cellular CDMA and IMT-2000. Simulation results for antenna gain at 859 MHz and 2027.5 MHz were 2.38 dBi and 4.02 dBi respectively with omni directional radiation pattern. The size of implemented antenna is compact and the antenna can be produced in low cost enough for commercialization.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2017.10a
• /
• pp.55-56
• /
• 2017

In this paper, a wideband loop antenna is designed using a CPW feeding method for indoor digital TV applications. The proposed loop antenna consists of a square loop and two circular sectors which connect the loop with central feed points, and the CPW feed line is inserted in the lower circular sector. The CPW feed line is designed to match with the 75 ohm port impedance for DTV applications, and the ground slots are etched in order to improve the impedance matching in the middle frequency region. The optimized antenna is fabricated on FR4 substrate, and the experiment results show that it operates in the frequency band of 463-1,280 MHz for a VSWR < 2, which assures the operation in the DTV band.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.41 no.10
• /
• pp.820-826
• /
• 2013

In this paper, a compact and wideband CLAS(Conformal Load bearing Antenna Structure) was studied using smart skin technique. In order to satisfy the electrical performance of the CLAS antenna, the proposed CLAS antenna is composed of conductive mesh, face-sheet, radiator, honeycomb, housing. Especially, radiator is composed of composite magneto-dielectric material and radiating element etched on the PCB (Printed Circuit Board). The radiating element is inserted into the composite magneto-dielectric material and has sloted Folded LP(Log Periodic) structure. By fabricated composite magneto-dielectric, the resonance frequency is decreased and the impedance matching characteristics is improved. We verified that the antenna has wideband characteristics and compact size using the antenna test results.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.12
• /
• pp.1044-1052
• /
• 2016

In this paper, a cavity back slot antenna with a rotated rectangular patch is proposed. The proposed antenna consists of a ground plane with cavity structure, a microstrip feed line, and a rectangular patch with slot. With a dimension of $55mm{\times}40mm{\times}10mm$, the proposed antenna has the wide bandwidth due to the cavity structure. Measured 10 dB return loss bandwidth and fractional bandwidth of the proposed antenna is 5,030 MHz(3.02~8.05 GHz) and 90.9 % at the center frequency of 5.05 GHz. The proposed antenna is designed and simulated using ANSYS HFSS v.15.0.0. The designed antenna is fabricated and tested to validate its performances.