• Proceedings of the KIEE Conference
• /
• 1989.07a
• /
• pp.571-575
• /
• 1989

A position control system of D.C. Servo motor based on discrete variable structure system with sliding mode is presented. The sliding mode has been designed for a continuous system, but it is often realized in digital fashion because the complex switching logic can be easily carried out. In digital control system, the ideal sliding mode does not occur since the structure can't be switched during sampling interval. However, there can be exist a motion which is confined to a regoin including the sliding surface and proceeds to the origin along the surface. This notion is called quasisliding mode. In this paper, we introduce this control scheme to the D.C. Servo motor position control in order to reduce the chattering phenonenon.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.14 no.5
• /
• pp.385-393
• /
• 2004

This paper proposes a swing-arm type dual-stage actuator, which consists of a PZT actuator for fine motion and a VCM(voice coil motor) for coarse motion, for an SFF ODD(small form factor optical disk drive), in order to achieve fast access speed and precise track-following control. Over the past few decades there have been a lot of researches related to the VCM and dual-stage actuator. In this paper, we focus our attention on the design and control of the PZT actuator. Due to the dual cantilever structure. the PZT actuator can generate precise translational tracking motion at its tip to which an optical pickup is attached. and the effect of hysteric behavior of the PZT element is reduced. The dynamic model of the PZT actuator is derived by using the Hamilton's principle, and verified by comparing it with the experimental frequency response. The sliding mode control is designed in order to be robust against modeling uncertainties. Simulations and experimental results confirm the effectiveness of the suggested control scheme.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.1679-1680
• /
• 2008

DC motor has been widely used in industrial applications, because the performance is excellent on the speed and position system. However, when a system has parameter uncertainty, it is very difficult to guarantee its performance. Sliding mode control is robust for parameter uncertainty. However conventional sliding mode control can not have the properties of PID controller because its sliding surface has lower order dynamics than the original system. In this paper the sliding surface design method is proposed by using virtual state for DC motor speed control. Its design is based on the augmented system whose dynamics have one higher order than that of the original system. As a result, in spite of the parameter uncertainty, the proposed sliding surface can have the same dynamic of nominal system controlled by PID controller. And the reaching phase is removed by setting an initial state which makes the initial sliding surface equal to zero.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1999.10a
• /
• pp.148-153
• /
• 1999

In this paper, it is proposed the adaptive-sliding mode control technique which is new approach to implement the robust control of industrial robot manipulator with external disturbances and parameter uncertainties. Over the past decade, the design of advanced control systems for industrial robotic manipulators has been a very active area of research and two major design categories have emerged. Sliding mode control is a well-known technique for robust control of uncertain nonlinear systems. The robustness of sliding model controllers can be shown in continuous time, but digital implementation may not preserve robustness properties because the sampling process limits the existence of a true sliding mode. Adaptive control algorithm is designed by using the principle of the model reference adaptive control method based upon the hyperstability theory. The proposed control scheme has a simple structure is computationally fast and does not require knowledge of the complex dynamic model or the parameter values of the manipulator or the payload. Simulation results how that the proposed method not only improves the performance of the system but also reduces the chattering problem of sliding mode control. Consequently, it is expected that the new adaptive sliding mode control algorithm will be suited for various practical applications of industrial robot control system.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.11a
• /
• pp.424-429
• /
• 2003

This paper proposes a swing-arm type dual-stage actuator, which consists of a PZT actuator for fine motion and a VCM(Voice Coil Motor) for coarse motion, for SFF ODD(Small Form Factor Optical Disk Drive), in order to achieve fast access speed and precise track following control. We focus our attention on the design and control of the PZT actuator, because there have been a lot of previous researches related to the VCM and dual-stage actuators. Due to the dual cantilever structure, the PZT actuator can generate precise translational tracking motion at its tip where optical pickup is attached at, and the effect of hysteric behavior of the PZT element is reduced. The dynamic model of the PZT actuator is derived by using the Hamilton's principle, and verified by comparing with the experimental frequency response. The sliding mode control is designed in order to be robust against modeling uncertainties. Simulations and experimental results confirm the effectiveness of the suggested control scheme.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.4 s.97
• /
• pp.163-177
• /
• 1999

Polishing work for a curved surface die demands simple and repetitive operations and requires much time while it demands also high precision. Therefore it is operated by a skilled worker in handiwork. However the workers avoid gradually a polishing work because of the poor environmental conditions such as dust and noise. In order to reduce the polishing time and to alleviate the problem of shortage of skilled workers, an automatic polishing robot system which is composed of a polishing robot with two degrees of freedom motion and pneumatic system is developed, and it is attached to machining center with three degrees of freedom. The system keeps the polishing tool vertically on the surface of die and maintains constant pneumatic pressure. The polishing robot with DSP(digital signal processor) controller is controlled by sliding mode control. A synchronization between machining center and polishing robot is accomplished by using M code of machining center. A performance experiment for polishing work is executed by the developed automatic polishing robot system. The result shows that the developed automatic polishing robot has a good performance and well polished workpiece surface is obtained.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.16 no.4
• /
• pp.137-143
• /
• 2021

We propose an adaptive non-singular terminal sliding-mode control for the fast finite-time convergence (FANTSMC) in robot manipulator. The proposed FANTSMC approach is developed to be applied without singularity in robot manipulator, which has a new pole-placement control with the non-singular terminal sliding variable while generating the desirable control torque. Moreover, the switching gain is designed to suppress the time-delayed estimation error appropriately, which aims at providing the high robust tracking performance. Also, the proposed one employs one-sample delayed information to cancel out the system uncertainties and disturbances. For these reasons, it offers strong attraction within the finite time. It is shown that the tracking performance of the proposed FANTSMC approach is guaranteed to be uniformly ultimately bounded through the Lyapunov stability. The effectiveness of the proposed FANTSMC approach is illustrated in simulations, which is compared with that of the up-to-date control approach.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.3
• /
• pp.102-109
• /
• 2005

Wheel-slip control systems are able to control the braking force more accurately and can be adapted to different vehicles more easily than conventional ABS systems. But, in order to achieve the superior braking performance through the wheel-slip control, real-time information such as the tire braking force is required. For example, in the case of EHB (Electro-Hydraulic Brake) systems, the tire braking force cannot be measured directly, but can be approximated based on the characteristics of the brake disk-pad friction. The friction characteristics can change significantly depending on aging of the brake, moisture on the contact area, heat etc. In this paper, a wheel slip The proposed wheel slip control system is composed of two subsystems: braking force monitor and robust slip controller In the brake force monitor subsystem, the tire braking forces as well as the brake disk-pad friction coefficient are estimated considering the friction variation between the brake pad and disk. The robust wheel slip control subsystem is designed based on sliding mode control methods and follows the target wheel-slip using the estimated tire braking forces. The proposed sliding mode controller is robust to the uncertainties in estimating the braking force and brake disk-pad friction. The performance of the proposed wheel-slip control system is evaluated in various simulations.

• Journal of Institute of Control, Robotics and Systems
• /
• v.21 no.5
• /
• pp.421-426
• /
• 2015

Need to develop human body's posture supervised robots, gave the push to researchers to think over dexterous design of exoskeleton robots. It requires to develop quantitative techniques to assess human motor function and generate the command to assist in compliance with complex human motion. Upper limb rehabilitation robots, are one of those robots. These robots are used for the rehabilitation of patients having movement disorder due to spinal or brain injuries. One aspect that must be fulfilled by these robots, is to cope with uncertainties due to different patients, without significantly degrading the performance. In this paper, we propose chattering free sliding mode control technique for this purpose. This control technique is not only able to handle matched uncertainties due to different patients but also for unmatched as well. Using this technique, patients feel active assistance as they deviate from the desired trajectory. Proposed methodology is implemented on seven degrees of freedom (DOF) upper limb rehabilitation robot. In this robot, shoulder and elbow joints are powered by electric motors while rest of the joints are kept passive. Due to these active joints, robot is able to move in sagittal plane only while abduction and adduction motion in shoulder joint is kept passive. Exoskeleton performance is evaluated experimentally by a neurologically intact subjects while varying the mass properties. Results show effectiveness of proposed control methodology for the given scenario even having 20 % uncertain parameters in system modeling.

• Journal of Aerospace System Engineering
• /
• v.13 no.2
• /
• pp.26-33
• /
• 2019

Control moment gyro (CMG) employed as satellite actuators, generates a large torque through the steering of its gimbals. Although each gimbal holds a high-speed rotating wheel, the wheel imbalances induces disturbance and degrades the satellite control quality. Therefore, the disturbances ought to be detected and identified as a precaution against actuator faults. Among the method used in detecting disturbances is the state observers. In this paper, we apply a continuous second order sliding mode observer to detect single disturbances/faults in CMGs. Verification of the algorithm is also done on the hardware satellite simulator where four CMGs are installed.