• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1989년도 제9회 학술강연회초록집
• /
• pp.48-59
• /
• 1989

최근 터어보 샤프트, 터어보 팬, 터어보 쳇트 엔진, 가스 터어빈, 공작기계의 주축, 그리고 섬유기계 섬유봉등의 회전기계류 설계에서 단위 무게당 출력의 비율을 높이기 위해서 회전속도의 고속화가 요구되고 있다. 이러한 경우 회전축계의 진동특성에 크게 영향을 미치는 감쇠특성을 부각시키기 위하여 베어링의 외부에 스퀴즈-필름 댐퍼 (Squeeze-film Damper)를 부가하고 회전축계를 유연하게 지지하여 줌으로써 진동문제를 간단히 해결하며 회전속도의 고속화를 가능하게 할 수 있다. 적합하게 설계된 스퀴즈-필름 댐퍼의 잇점은 다음과 같다. (a) 회전축의 위험속도를 작은 공진쪽으로서 통과하는 것이 가능. (b) 베어링과 지지구조물에 전달되는 하중이 감소 (c) 장기간 사용중, 마모 및 브레이드 파손에 의해 진폭이 증가된 불평형 강제진동에서도 안정된 운전이 가능 (d) 미끄럼 저어널 베어링에 지지된 회전축계의 고속회전에서 불안정한 자려진동이 나타나는 안정 한계속도를 높히는 것이 가능

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1992년도 제15회 학술강연회초록집
• /
• pp.77-81
• /
• 1992

스퀴즈 필름 댐퍼 (Squeeze Film Damper, SFD)는 구조가 단순하면서도 감쇠성능이 우수하여 구름베어링에 지지된 고속회전체의 댐퍼로 이용되고 있으며 특히 대부분의 항공기용 터보엔진에 장착되어 고속회 전체의 댐퍼로서의 우수성을 보여주고 있다. 또한 동력기계의 단위 무게당 고출력화 경향으로 인하여 회전체의 경량화와 고속회전은 더욱 절실히 요구되고 있다. 이에따라 기계의 회전속도를 제 1차 또는 제 2차 위험속도(critical speed)이상까지 상승시켜야 하므로 SFD의 활용범위는 앞으로도 점차 증가할 것이다. 본 논문에서는 Swift-Stieber 경계조건을 적용하여, 공동현상이 발생하는 무한 폭 SFD의 유막력과 감쇠계수를 구한 후 강성 및 유연회전체의 정상상태 응답을 해석함으로써 공동현상이 회전체-SFD계의 진동에 미치는 영향을 연구하고자 한다.

• Tribology and Lubricants
• /
• 제40권1호
• /
• pp.28-37
• /
• 2024

This paper presents the development of a squeeze film damper (SFD) test rig and experimental identification of the effects of clearance, damper length, journal eccentricity ratio, excitation amplitude, oil supply pressure, and oil flow rate on the damping coefficients of a test SFD with open ends and a central groove. Test data are compared with predictions from a simple model developed for short SFDs with open ends and a central groove. The test results show a significant decrease in the damping coefficient with increasing clearance and a dramatic increase with damper length, which are in good agreement with the simple model predictions. According to the simple model, the damping coefficient is inversely proportional to the cube of the clearance and directly proportional to the cube of the length. An increase in the journal eccentricity ratio results in a dramatic increase in the damping coefficient by as much as 15 times that of the concentric case, particularly at low excitation frequencies. By contrast, the measured damping coefficient remains almost constant with changes in the excitation amplitude and supply pressure, which are not major factors in the damper design. In general, the test data agree well with the simple model predictions, excluding cases that show increases in the SFD length and journal eccentricity, which indicate significant dependency on the excitation frequency.

• Tribology and Lubricants
• /
• 제40권2호
• /
• pp.54-60
• /
• 2024

This study experimentally identifies the effects of end shape, clearance, total damper length, journal eccentricity ratio, oil supply pressure, and oil flow rate on the damping coefficient of a squeeze film damper (SFD) with piston ring seal ends and a central groove. The SFD is composed of a lubricating fluid flowing between the outer race of a rolling element bearing and cartridge, along with an anti-rotation pin to prevent the rotation of the outer race. The device provides additional viscous damping to a rotating system. Additionally, piston ring seals attached at both ends of the damper increase the damping coefficient of the rotating system by reducing oil leakage. Because these different design conditions affect the damping coefficient of an SFD, we perform experiments including different conditions. Tests show that the damping coefficient increases significantly in the SFD with piston ring seal ends compared with the SFD with open ends. The damping coefficient also increases with increasing total damper length and journal eccentricity ratio, and decreases with increasing clearance. Additionally, in contrast to the trend observed for the SFD with open ends, the damping coefficient for the SFD with piston ring seal ends increases with increasing supply pressure and flow rate as the frequency decreases but shows consistent results as the frequency increases.

• 한국소음진동공학회논문집
• /
• 제21권6호
• /
• pp.553-561
• /
• 2011

A theoretical approach is carried out to predict the quality factors of flexible modes of a microcantilever on a squeeze-film. The frequency response function of an inertially-excited microcantilever beam is derived using an Euler-Bernoulli beam theory. The external force due to squeeze-film phenomenon is developed from the Reynolds equation. Slip boundary conditions are employed at the interfaces between the fluid and the structure to consider the gas rarefaction effect, and pressure boundary condition at both ends of fluid analysis region is enhanced to increase the exactness of predicted quality factors. To the end, an approximate equation is derived for the first bending mode of the microcantilever. Using the approximate equation, the quality factors of the second and third bending modes are calculated and compared with experimental results of previously reported work. The comparison shows the feasibility of the current approach.

• Tribology and Lubricants
• /
• 제16권2호
• /
• pp.75-83
• /
• 2000

The present paper proposes a new type of an electro-rheological squeeze film damper (ER SFD) of which the damping capacity can be controlled by the application of electric field. The new ER .SFD- is sealed with slotted rings having electrodes at the inside of the constant gap. The ER SFD can provent the problem of electric short which might be occurred in a previous ER SFD. Reynolds lubrication equation for a Newtonian fluid and the end leakage equation for ER fluids are numerically solved to get the pressure distributions and the damping coefficients of the ER SFD. The results show that the damping coefficients greatly increase with increasing the yield shear stress of ER fluid. In addition, the unbalance response analysis of a flexible rotor supported on the new ER SFD implies that the rotor system can be operated with the minimum of rotor amplitude and force transmissibility by controlling the yield shear stress of ER fluids properly.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 추계학술대회논문집
• /
• pp.702-707
• /
• 2005

The equations of motion of the structure, which is a small scale cantilever beam considering electrostatic force, squeeze film damping and van der Waals force are obtained employing Galerkin's method based on Euler beam theory. The influence of each force is investigated fur changing the size of a small scale cantilever beam which assumed uniform shape. Also the forces which are affected by the required size of a small scale cantilever beam for manufacturing are forecasted.