• Journal of the Korean Wood Science and Technology
• /
• v.43 no.6
• /
• pp.746-756
• /
• 2015

The goal of this study was to review the wood shrinkage published in Journal of The Korean Wood Science and Technology from 1976 to 2015. Previous studies reported that shrinkage from Larix kaempferi in the tangential, radial, longitudinal directions ranged from 4.21%-9.79%, 2.09%-4.67%, 0.17%-0.33%, respectively. When different drying methods including closed cylinder drying, oven drying, and room temperature drying were used, volumetric shrinkage of Dipterocarpus grandiflorus was different, ranging from 31.6% to 21.0%. With an increment of the drying temperature of $115^{\circ}C$, $120^{\circ}C$, $125^{\circ}C$, the shrinkage of Larix kaempferi did not show a consistent trend. When sample size of Pinus densiflora was increased from $20{\times}20{\times}20mm$ to $100{\times}100{\times}100mm$, the tangential, radial and volumetric shrinkage decreased 2.61%, 1.32%, 0.80%, respectively. When a caliper having a sensitivity of 0.01 mm was used to measure $20mm^3$ specimen from Cryptomeria japonica, the measurement error occurred 1.97% in the radial direction and 35.7% in the longitudinal direction. From the previous studies, wood shrinkage could be influenced by sample size, drying method and measurement technique.

• Journal of the Korean Ceramic Society
• /
• v.39 no.11
• /
• pp.1083-1089
• /
• 2002

Densification and grain growth behavior of MgO and -doped alumina ceramics were investigated. MgO was found to inhibit grain growth and to promote densification, but acted to promote grain growth more than densification. The density which showed the maximum shrinkage rate was investigated in the plot of shrinkage rate versus density. The data suggests that the maximum shrinkage rate separates the two kinetic regimes, below the density of maximum shrinkage, the regime associated with densification and above the maxima, the regime associated with the grain growth. The plot exhibits a maximum which shifts to higher temperatures with MgO doping and to lower with doping.

• Elastomers and Composites
• /
• v.38 no.4
• /
• pp.295-302
• /
• 2003

The amount of shrinkage of injection molded parts is different from operational conditions of injection molding such as injection temperature, injection pressure and mold temperature, and mold design such as gate size. It also varies depending on the presence of crystalline structure in resins. In this study, part shrinkage was investigated for various operational conditions and resins. Poly(butylene terephthalate) (PBT) for crystalline polymer, and polycarbonate (PC) and poly(methyl methacrylate) (PMMA) for amorphous polymers were used. Crystall me polymer showed higher part shrinkage by about three times than that of amorphous polymers. Part shrinkage increased as melt and molt temperatures increased, and injection pressure decreased. Part shrinkage decreased as gate size increased since the pressure delivery is mush easier for larger gate sizes. Part shrinkage at the position close to the gate was larger than that or the position far from gate. This phenomenon might be occur by difference of residual stress.

• Proceedings of the Korean Society for Emotion and Sensibility Conference
• /
• 2001.11a
• /
• pp.19-24
• /
• 2001

본 연구에서는 국내 7개 기업에서 생산되고 있는 PET POY와 일본과 대만에서 생산되고 있는 PET POY 시료를 준비하여 이들 사의 열수축 특성을 hank 실험방법과 Toray FTA-500 계측기를 사용한 실험 data를 비교 분석하여 최근 도입되어 사용되고 있는 Toray FTA-500 열 수축률 측정계측기의 타당성을 조사하고자 한다. 본 연구를 위해 사용한 시료는 PET POY 85d/72f 그리고 120d/36f 그리고 120d/36f 2가지를 준비했으며 국내 합섬 maker 7개회사별로 각각 같은 굵기의 POY 사를 준비하였다. 그리고 국내 POY와 외국 소재로서 대만과 일본에서 생산되고 있는 소재의 열 수축률 특성치를 Toray FTA-500과 hank 방법을 비교 분석하므로서 감성의류 제조용 PET POY 사의 국내ㆍ외 소재의 차이점을 계측기계와 계측방법의 상이로 나누어 data화가 가능케 함으로서 감성의류소내 개발에 기초자료를 활용코자 한다.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2010.05a
• /
• pp.271-272
• /
• 2010

This thesis is researched to compare the shrinkage of lightweight concrete depending on depth to normal concrete. It is used artificial lightweight aggregate which has 20% of pre-absorb value by lightweight concrete. When water-binder ratio is 30%, average shrinkage of lightweight concrete section decreased than normal concrete, but differential shrinkage of lightweight concrete section increased. However water-binder ratio is 40%, average shrinkage and differential shrinkage of lightweight concrete section decreased than normal concrete.

• Proceedings of the Korean Society of Dyers and Finishers Conference
• /
• 2011.11a
• /
• pp.27-27
• /
• 2011

일반 나일론6 폴리머 대비 수축률이 높은 수축률을 가질 수 있는 나일론 고수축 개질 폴리머를 개발하고 이를 이용하여 고권축/고벌키 특성이 우수한 세섬 20d급의 나일론/Co-나일론계 고권축 소재를 개발하기 위하여 나일론 개질폴리머의 구조와 물성에 대한 연구 조사가 필요하다. 기존 나일론6 중합은 카프로락탐만을 사용하여 중합되므로 선형의 분자 구조를 가지게 되어 섬유형태로 방사했을 경우 수축률이 균일하게 되므로 수축율이 다른 나이론 폴리머를 만들기 위해서는 카프로락탐 외에 폴리머 분자구조를 변화 시킬 수 있는 공중합 모노머를 사용하여 랜덤하게 공중합을 해야한다. 일반적으로 사용되는 공중합 모노머는 말단이 -COOH나 -NH2로 되어서 카프로락탐과 반응할 수 있는 물질이 많이 사용되어 진다. 최근 수축률을 높이기 위한 공중합 모노머로는 SSIPA나 Meta xylene diamine과 같이 비 선형구조를 가지는 모노머를 사용하여 폴리머의 구조를 변화시켜 수축율을 높이고 있다. 이를 일반 나이론 6와 사이드 바이 사이드 방사를 하게 되면 두 폴리머의 수축율 차이로 인해 미케니컬 수축력을 발현시키고 있다. 따라서 본 연구에서는 스포츠/레저용 초경량 Nylon 박지에 적합한 자발신장 개념인 Nylon6 잠재권축 소재를 개발하기 위하여 $14^D$수준의 Co-Nylon6의 구조와 물성을 조사 검토하여 이를 실제 현장에 자료를 제공하는 것을 목적으로 하였다.

• Journal of the Korea Concrete Institute
• /
• v.18 no.3 s.93
• /
• pp.397-404
• /
• 2006

This paper investigates experimentally the effect of combined addition of expansive additive and shrinkage reducing agent(SRA) on setting time, compressive strength and drying shrinkage of concrete. An increase of EA and SRA content leads to a reduction in flowability, which causes the increase of superplasticizer dosage, while air content increases. For setting time, in spite of increased superplasticizer dosage, with the increase of EA and SRA, setting time shortens. This is due to the presence of alkali ion by SRA and the faster formation of ettringite. At dosage of 5.0% of EA, concrete has the highest compressive strength and above that dosage, compressive strength decreased. On the contrary, the increase of SRA dosage results in a decrease in compressive strength. Combined addition of EA of 5.0% and SRA of 1.0% shows a comparable strength with control concrete. For drying shrinkage, as expected, the increase of EA and SRA dosage leads to reduction of drying shrinkage markedly. Moreover, combined addition of EA and SRA has better drying shrinkage reduction effect than individual use of EA and SRA by as much as $5{\sim}16%$. Optimal combination of EA and SRA is fixed at 5.0% of EA and 0.5% of SRA based on the consideration of the effect of EA and SRA on fresh state, compressive strength and shrinkage of concrete.

• The Journal of Korean Academy of Prosthodontics
• /
• v.48 no.1
• /
• pp.55-60
• /
• 2010

Purpose: The shrinkage of dental resin cement may cause several clinical problems such as distortion that may jeopardize the accurate fit to the prepared tooth and internal stress within the restorations. It is important to know the polymerization shrinkage-strain of dental resin cement to reduce clinical complications. The purpose of this study was to investigate the polymerization shrinkage-strain kinetics of six commercially available dental resin cements. Material and methods: Three self-cure resin cements (Fujicem, Superbond, M-bond) and three dual-cure resin cements (Maxcem, Panavia-F, Variolink II) were investigated. Time dependent polymerization shrinkage-strain kinetics of the materials were measured by the Bonded-disk method as a function of time at $23^{\circ}C$, with values particularly noted at 1, 5, 10, 30, 60, 120 min after mixing. Five recordings were taken for each materials. The data were analyzed with one-way ANOVA and Scheffe post hoc test at the significance level of 0.05. Results: Polymerization shrinkage-strain values were 3.72%, 4.19%, 4.13%, 2.44%, 7.57%, 2.90% for Fujicem, Maxcem, M bond, Panavia F, Superbond, Variolink II, respectively at 120 minutes after the start of mixing. Panavia F exhibited maximum polymerization shrinkage-strain values, but Superbond showed minimum polymerization shrinkage-strain values among the investigated materials (P < .05). There was no significant differences of shrinkage-strain value between Maxcem and M bond at 120 minutes after the start of mixing (P > .05). Most shrinkage of the resin cement materials investigated occurred in the first 30 minutes after the start of mixing. Conclusion: The onset of polymerization shrinkage of self-cure resin cements was slower than that of dual-cure resin cements after mixing, but the net shrinkage strain values of self-cure resin cements was higher than that of dual-cure resin cements at 120 minutes after mixing. Most shrinkage of the dental resin cements occurred in the first 30 minutes after mixing.

• Restorative Dentistry and Endodontics
• /
• v.32 no.1
• /
• pp.28-36
• /
• 2007

The purpose of this study was to compare the effect of exponential curing method with conventional curing and soft start curing method on polymerization shrinkage of composite resins. Three brands of composite resins (Synergy Duo Shade, Z250, Filtek Supreme) and three brands of light curing units (Spectrum 800, Elipar Highlight, Elipar Trilight) were used. 40 seconds curing time was given. The shrinkage was measured using linometer for 90 seconds. The effect of time on polymerization shrinkage was analysed by one-way ANOVA and the effect of curing modes and materials on polymerization shrinkage at the time of 90s were analysed by two-way ANOVA. The shrinkage ratios at the time of 20s to 90s were taken and analysed the same way. The results were as follows : 1. All the groups except Supreme shrank almost within 20s Supreme cured by soft start and exponential curing had no further shrinkage after 30s (p < 0.05). 2. Statistical analysis revealed that polymerization shrinkage varied among materials (p = 0.000) and curing modes (p = 0.003). There was no significant interaction between material and curing mode. 3. The groups cured by exponential curing showed the statistically lower polymerization shrinkage at 90s than the groups cured by conventional curing and soft start curing (p < 0.05). 4. The initial shrinkage ratios of soft start and exponential curing were statistically lower than conventional curing (p < 0.05). From this study, the use of low initial light intensities may reduce the polymerization rate and, as a result, reduce the stress of polymerization shrinkage.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2002.07a
• /
• pp.188-194
• /
• 2002

버섯의 감압건조시험을 할 수 있는 요인시험장치를 제작하여 시험한 결과를 요약하면 다음과 같다. 가. 댐퍼조절방식 감압건조장치로 건조시험한 결과, 표고버섯은 건조온도 5$0^{\circ}C$에서는 나타나 건조실 압력에 따른 건감률의 변화는 크게 나타나지 않았으나, 건조온도 6$0^{\circ}C$에서 건조실 내부압력이 990hPa일 때 4.57%/hr로 1,013hPa에 비해 높게 나타났으며, 색차면에서는 온도 5$0^{\circ}C$일 때 건조실 내부 압력이 낮아질수록 변화가 적은 것으로 나타났고, 수축률은 압력별로 거의 변화가 없었으나, 건조온도 6$0^{\circ}C$, 압력 990hPa에서 다른 조건에 비해 양호한 것으로 판단되었으나 건조실 내부에 공기분배가 일정하지 않고, 건조실 내부압력 강하성능이 떨어지는 문제점이 발생하여 솔레노이드를 이용한 압력조절방식으로 보완 제작하여 건조시험을 실시하였다. 나. 솔레노이드방식 감압건조장치로 건조시험 한 결과, 표고버섯은 열풍온도 5$0^{\circ}C$, 건조실 내부압력 940-980hPa에서 건감률 2.69%w.b./hr, 갓의 복원률 90.1%로 가장 높았고, 색차 및 수축률이 가장 낮은 것으로 나타났으며, 건조실 내부압력을 900-940hPa로 고정하고 열풍온도를 40, 50, 6$0^{\circ}C$로 표고버섯을 시험한 결과 건감률은 6$0^{\circ}C$일 때 가장 높았으나, 색차, 수축률, 복원률을 고려할 경우 열풍온도 5$0^{\circ}C$가 가장 적합한 것으로 판단된다. 다 솔레노이드방식 감압건조장치로 건조한 표고버섯으로 품위에 대한 유의성 검증결과, 표고버섯의 경우 온도별로는 색택과 복원률, 건조실 내부 압력별로는 수축률, 복원률에서 유의차가 있는 것으로 나타났다. 라. 본 연구에서 구명된 감압건조특성을 기초로 하여 배치식 감압건조기를 설계 제작에 활용하고자 한다.