• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.20 no.2
• /
• pp.181-190
• /
• 2007

The linkage framework of surface geometric modeling based on the NURBS and shell finite element analysis is developed in this study. In the geometrically exact shell finite element analysis, the accuracy of the analysis strongly depends upon the accurate computation of the surface geometric quantities. Therefore if we obtain the necessary geometric quantities from the NVRBS surface equation, it's possible to construct the effective linkage framework of surface modeling in the CAD systems and shell finite element analysis using geometrically exact shell finite element. Besides, the linkage framework can be applied to the analysis of general and complex surfaces as well as simple surfaces. In this study, the shell surfaces are generated by interpolating given set of data points based on the NURBS surfaces. These data points usually can be obtained from surface scanning. But the representations of the generated NURBS surface are not same to one another. The accuracy depends on the chosen parameterization methods used in NURBS. Therefore, it is needed to select the suitable parameterization method according to the geometry of the surfaces. To verify the performance and accuracy of our developed linkage framework, we solve several well-known benchmark problems and assess the performance of the developed method.

• Tunnel and Underground Space
• /
• v.30 no.5
• /
• pp.473-483
• /
• 2020

This paper examines the vertical stress change concentrated on mine pillar which occurs due to the stress disturbance from opening excavation at room and pillar mine by FLAC3D, a finite difference method (FDM) software. The mesh size combination is decided with a careful consideration of relative error and run-time, then its performance is verified. A series of numerical analyses is conducted and the vertical stress at central pillar was observed for the test cases of 1×1 to 11×11 mine pillars, 40 m to 320 m depth with 40 m difference. The results show that the vertical stress of pillar approaches to the similar value with the value estimated by tributary area theory(TAT) when the development area (N_P) is increased or the height of overburden (H_OB) is decreased, while it is overestimated in the opposite case. Furthermore, it also represents that the vertical stress factor (VSF) converges to a specific value when the depth is increased whille keeping the development area identical.

• Journal of Advanced Navigation Technology
• /
• v.14 no.5
• /
• pp.684-690
• /
• 2010

Recently, the NG(Next Generation) system is studied for supporting convergence of various services and multi mode of single terminal. And a demand of user for taking the various services is getting increased, for supporting these services, many systems being able to transmit a large message have been appeared. In the NG system, it has to be supporting the CDMA and WCDMA besides the tele communication systems using OFDM method with single terminal An intergrated system can be improved with adopting of SoC technique. For adopting SoC technique on the intergrated terminal, we have to solve the non linear problem of HPA(High Power Amplifier). Nonlinear characteristic of HPA distorts both amplitude and phase of transmit signal, this distortion cause deep adjacent channel interference. We adopt a polynomial pre-distortion technique for this problem. In this paper, a noble modem design for NG mobile communication service and a method using polynomial pre-distorter with PAPR technique for counterbalancing nonlinear characteristic of the HPA are proposed.

• Journal of KIISE:Software and Applications
• /
• v.27 no.7
• /
• pp.731-741
• /
• 2000

This paper proposes a method to detect a facial region and extract facial features which is crucial for visual recognition of human faces. In this paper, we extract the MER(Minimum Enclosing Rectangle) of a face and facial components using projection analysis on both edge image and binary image. We use an active contour model(snakes) for extraction of the contours of eye, mouth, eyebrow, and face in order to reflect the individual differences of facial shapes and converge quickly. The determination of initial contour is very important for the performance of snakes. Particularly, we detect Minimum Enclosing Rectangle(MER) of facial components and then determine initial contours using general shape of facial components within the boundary of the obtained MER. We obtained experimental results to show that MER extraction of the eye, mouth, and face was performed successfully. But in the case of images with bright eyebrow, MER extraction of eyebrow was performed poorly. We obtained good contour extraction with the individual differences of facial shapes. Particularly, in the eye contour extraction, we combined edges by first order derivative operator and zero crossings by second order derivative operator in designing energy function of snakes, and we achieved good eye contours. For the face contour extraction, we used both edges and grey level intensity of pixels in designing of energy function. Good face contours were extracted as well.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.43 no.6
• /
• pp.507-515
• /
• 2015

This paper proposes a filtering method for effective state vector estimation of highly maneuvering target. It is needed to hit the point called 'sweet spot' to increase the kill probability in missile interception. In paper, a filtering method estimates the length of a moving target tracked by a frequency modulated continuous wave (FMCW) radar. High resolution range profiles (HRRPs) is generated from the radar echo signal and then it's integrated into proposed filtering method. To simulate the radar measurement which is close to real, the study on the properties of scattering point of the missile-like target has been conducted with ISAR image for different angle. Also, it is hard to track the target efficiently with existing Kalman filters which has fixed measurement noise covariance matrix R. Therefore the proposed method continuously updates the covariance matrix R with sensor measurements and tracks the target. Numerical simulations on the proposed method shows reliable results under reasonable assumptions on the missile interception scenario.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.18 no.2
• /
• pp.236-242
• /
• 2008

In this paper, we propose an optimized fuzzy controller based on Hierarchical Fair Competition-based Genetic Algorithms (HFCGA) for rotary inverted pendulum system. We adopt fuzzy controller to control the rotary inverted pendulum and the fuzzy rules of the fuzzy controller are designed based on the design methodology of Linear Quadratic Regulator (LQR) controller. Simple Genetic Algorithms (SGAs) is well known as optimization algorithms supporting search of a global character. There is a long list of successful usages of GAs reported in different application domains. It should be stressed, however, that GAs could still get trapped in a sub-optimal regions of the search space due to premature convergence. Accordingly the parallel genetic algorithm was developed to eliminate an effect of premature convergence. In particular, as one of diverse types of the PGA, HFCGA has emerged as an effective optimization mechanism for dealing with very large search space. We use HFCGA to optimize the parameter of the fuzzy controller. A comparative analysis between the simulation and the practical experiment demonstrates that the proposed HFCGA based fuzzy controller leads to superb performance in comparison with the conventional LQR controller as well as SGAs based fuzzy controller.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.109-112
• /
• 2008

In this study, Assessment of bond property of HSC with the rate of Blust-furnace(0, 12, and 25 percent by weight cement) and Evaluation of the relationship of the compressive strength coefficient (${\beta}$) between compressive strength with 40${\sim}$120MPa were performed. Design and Test of Bond specimens were carried out based on the ASTM C-234. Test results are follows, most specimens showed that the splitting failure in all specimens, except for B-40 series which showed that the pull-out failure. For the B-40 Series, the relation of compressive strength versus bond stress has well converged that of the proposed equation with the variation(${\beta}$=2/3) in UCB/E.E.R.C-83. The crack strength of concrete in splitting was proportioned to the compressive strength of concrete, and was the highest on the contents of blast furnace slag to 12 percent by weight of cement in each series, except for B-60 series. In the relation of admixture replacement rate versus maximum bond stress, The maximum bond stress was the highest in 12 percent by weight of cement according to less than 40MPa, and was the highest in 25 percent by weight of cement according to 80MPa.

• Journal of the Korean Geotechnical Society
• /
• v.28 no.6
• /
• pp.19-29
• /
• 2012

Pack micropiles were recently developed to improve pile capacity of general micropiles. Pack micropiles were made by warping thread bar or steel pipe of general micropile by geotexlile pack and grouting inside the pack with pressure. According to the pressure, the boring hole could be enlarged. A series of pile uplift tests were performed on three micropiles. Two out of the three piles were the pack micropiles and the other was the general micropile, in which a thread bar was used in the boring hole. According to the pressure applied to the pack micropiles, the diameter of boring hole was enlarged from 152 mm to 220 mm. Unit skin friction mobilized on side surfaces of micropiles increased with displacement of pile head and reached on a constant value, which represents that the relative displacement between piles (or thread bar) and soils was reached on critical state. And the uplift resistance of pack micropile was higher than that of general micropile. Two reasons can be considered: One is that the frictional surface increases due to enlarging diameter of boring holes and the other is that the unit skin friction could increase due to compressing effect of surrounding soils by soil displacement as much as the enlarging volume of boring hole. The compression effect appeared at deeper layer rather than surface layer. The unit skin friction mobilized on micropiles with small diameter was higher than the ones on large bored piles.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.14 no.1
• /
• pp.9-14
• /
• 2004

Rational sense is affected by emotion. If we add the factor of estimated emotion by environment information into robots, we may get more intelligent and human-friendly robots. However, various sensory information and pattern classification are prescribed for robots to learn emotion so that the networks are suitable for the necessity of robots. Neural network has superior ability to extract character of system but neural network has defect of temporal cross talk and local minimum convergence. To solve the defects, many kinds of modular neural networks have been proposed because they divide a complex problem into simple several subproblems. The modular neural network, introduced by Jacobs and Jordan, shows an excellent ability of recomposition and recombination of complex work. On the other hand, the recurrent network acquires state representations and representations of state make the recurrent neural network suitable for diverse applications such as nonlinear prediction and modeling. In this paper, we applied recurrent network for the expert network in the modular neural network structure to learn data pattern based on emotional assessment. To show the performance of the proposed network, simulation of learning the environment and behavior pattern is proceeded with the real time implementation. The given problem is very complex and has too many cases to learn. The result will show the performance and good ability of the proposed network and will be compared with the result of other method, general modular neural network.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2002.02a
• /
• pp.54-59
• /
• 2002

1. 일시수확형 고추의 기계수확 요인을 구명하기 위하여 4종류의 탈과장치를 제작하여 공시고추로 탈과시험을 실시한 결과 탈과장치는 방사대칭식(브러쉬형), 고추이송(공급)속도는 0.1m/s, 탈과장치 간격은 3cm, 탈과장치 회전수는 180rpm에서 정상탈과율 77.3%, 손상률 7.6% 미탈과율 3.0%로 가장 양호한 성적이 나타났다. 2. 방사대칭식(브러쉬형) 탈과장치를 이용하여 무지용 상향착과형 고추, 지주용 하향착과형 고추, 지주용 상향착과형 고추를 공시하여 고추별 탈과시험을 실시한 결과, 고추이송(공급)속도 0.1m/s, 원통사이간격 3cm, 탈과장치 회전수 180rpm에서 가장 양호한 성적이 나왔으며, 지주용 하향착과형 고추가 정상탈과률 82.7%, 손상률 7.4%, 미탈과율 2.7%로 무지주용 상향착과형 고추(52.3%, 14.3%, 12.5%)와 지주용 상향착과형 고추(77.3%, 7.6%. 3.0%)에 비해 기계수확에 적합한 것으로 나타났다. 3. 이상의 고추 기계수확 요인시험의 결과, 탈과장치는 방사대칭식(브러쉬형) 고추종류로는 하향착과형 고추가 기계수확에 바람직한 것으로 나타났으며, 수확 후 회수가 가능한 줄기부착고추를 포함한다면 고추기계수확률은 80% 이상, 꼭지가 떨어진 것이 대부분인 손상고추도 수확 후 즉시 기계건조하여 가공용으로 사용한다고 가정한다면 기계 수확률은 90% 이상 가능하지만, 이것의 수용 여부는 좀 더 폭넓은 의견수렴 및 조사가 필요하다고 사료된다. 4. 고추수확 기계화를 위해서는 실내요인 시험 결과를 토대로 포장에서 수확메커니즘 구명과 더불어 고추 과실이 크고 무지주용 하향착과형 일시수확형 고추 품종의 개발이 병행되어야 한다고 판단된다. 5) 마늘 선별작업 -마늘선별기는 작업성능이 높고 5등급으로 균일 선별되었으며 손상도 없었으나, 기계가 크고 무거워 이동이 곤란하고 가격이 비싸므로 선별등급을 3∼4단계로 줄이고 소형 농가보급형으로 개량제작이 요구됨. 나. 마늘재배 일관기계화에 의한 노동투하시간과 비용 -종자준비부터 통마늘선별까지의 일관기계화로 투입된 주요작업의 노력은 75∼76%가 절감되고, 재배규모 3ha기준시 비용은 44-53%절감되었음. the annealing texture. Observations by TEM and EBSD revealed the formation of very fine grains of ∼1.0$\mu\textrm{m}$ after CCSS.he dislocations form local defect arrangements at the grooves permitting the substantial reduction in defect density over the remainder of the interfacial area.한 최대의 감자 재배지역을 형성하였다. 제주도는 산지지형과 따뜻한 기온으로 2기작이 가능하고, 감자가공 공장설립과 교통발달에 따른 육지 시장과의 접근이 용이해졌기 때문에 남한에서 2번째로 큰 감자재배지역이 되었다.(요약 및 결론에서 발췌)그람양성균에서 효과적이었으며, 농도별 항균력시험 결과 농도가 증가할수록 비례하여 저해율도 증가함을 알 수 있었다. 첨가농도를 달리하여 미생물의 생육도를 측정한 결과, fraction II磎꼭\ulcorner경우 그람양성균에 대해 500 ppm 이상에서 뚜렷한 증식억제효과를 나타내었다.서 뚜렷한 증식억제효과를 나타내었다.