• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2007.12a
• /
• pp.34-36
• /
• 2007

현재 모형선을 이용한 선형성능 검증방법에는 크게 2가지 방법이 있다. 첫째는 예인수조에서 예인전차를 이용하여 정수중에 배를 예인시켜 그에 따른 저항을 시험하는 방법이 있고, 둘째는 회류수조에서 배를 고정하여 물을 회전시켜 모형선의 저항을 측정하는 방법이 있다. 이와 같은 방법은 저속 및 대형선박을 검증하기 위해 계발된 방법들로 소형 고속어선 및 고속레저선박의 저항성능 평가를 수행하기 어려운 것이 현실이다. 예인전차의 예인속도와 회류수조 물의 유속이 소형 고속어선 및 고속레저선박의 속력에 미치지 못하기 때문이다. 따라서 고속을 요하는 선박의 저항성능 평가를 위해 새로운 방법 연구가 필요하다. 이에 고속선의 저항성능 시험을 위해 실 해상에서 일반 선박을 이용하여 예인하는 방법을 적용하여 저항시험을 수행하였으며 그에 맞는 시스템을 설계하였다.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.16 no.3
• /
• pp.202-210
• /
• 2013

As incomes increase, interest in ocean leisure picks up. As a result, a lot of research and developments on hull form design and production of planing boats, mostly used for ocean leisure, are needed. Analysis in researches on resistance of planing boats shows that resistance characteristic of planing boats is different from resistance characteristic of general boats because the former is fast, and its wetted surface is very small. Using Savitsky formula widely used in the calculation of effective horse power in shipbuildingyards, and propulsion system and engine manufacturers, this study calculated total resistance of a research planing boat. Then it analyzed the flow characteristics of the planing boat through theoretical analysis and wind tunnel experiment, and computed air resistance and lift force by changes of speed and trim angle. It also compared and analyzed result of theoretical analysis and experiment of the ratio of air resistance to total resistance under variations of velocity and trim angle. When the study is used to estimate more accurate effective horse power, it is expected to remedy abuses of unnecessarily installing high-powered engine. As nature disasters due to abnormal changes of weather increase, interest in greenhouse gas grows. International Maritime Organization (IMO) legislated Energy Efficiency Design Index (EEDI) and Energy Efficiency Operational Indicator (EEOI) to reduce ship greenhouse gas emissions. But this index will be applied to over 400 tons ships, small ships, emitting more greenhouse gases than larege ships per unit power, will dodge the regulations. Thus, this study indicated a problem by calculating greenhouse gas emissions of an ocean leisure planning boat (a small ship), and suggested the need for EEDI of small ships.

• Journal of Korea Ship Safrty Technology Authority
• /
• v.5
• /
• pp.10-19
• /
• 2000

소형어선이나 일반적인 활주형선형은 부분적인 형상 수정을 거치게 되면 3차원 곡면으로 이루어진 선체의 외판을 2차원 평면상에 전개하여 표현할 수 있다는 특성을 가지고 있다. 이러한 점을 활용하여 전개도형에 따라서 제작된 얇은 FRP 판재를 선 요소들로 정의된 형틀 상에서 변형시켜 선체의 형상을 만들고 그 내부에 추가로 FRP를 적층 함으로서 선체를 완성하는 방법을 제안하고자 한다.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.27 no.7
• /
• pp.1023-1030
• /
• 2021

Korea Maritime Safety Tribunal (KMST) statistics released in of 2019 indicated that most collision accidents involving small-size vessels with less than 20 gross-tonnage occur mainly due to operational carelessness, such as forward-looking negligence and unskilled vessel control. As an effective remedy, training and education for vessel operators are being strengthened to prevent accidents. However, collision accidents are increasing, and technical measures are continuously developed to reduce accidents caused by human factors. In this study, an avoidance algorithm and prototype of terminal-controller against collision between two nearby vessels was developed for implementation on relative navigation control by adopting WAVE telecommunication technology. Moreover, several sea trial tests were performed to verify the collision avoidance algorithm and control system using two fishing vessels for dif erent scenarios.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2022.11a
• /
• pp.184-185
• /
• 2022

국제해사기구(IMO)에서는 2017년 미래선박으로서 자율운항선박(MASS)의 개념을 채택한 바 있으며, 실해역 운항을 위한 국제법규 및 규정 검토를 진행하고 있다. 무인선은 악천후시 유인선이 수행하기 힘든 임무를 대체하거나 지원하기 위하여 원격 혹은 자율적으로 운용되는 일종의 소형 자율운항선박을 의미한다. 선박해양플랜트연구소에서는 2011년부터 해양수산부 연구개발사업을 통하여, 무인선 아라곤호 시리즈를 개발하였으며, 아라곤1호, 2호, 3호 등 총 3척을 운용하고 있다. 해당 선박은 길이 8미터, 배수량 약 3톤급의 활주선형으로 원격운항, 경로추종 및 충돌회피 등 자율운항 기능이 적용되어 있다. 한편, 무인선은 공중 드론과 달리 탑재중량이 크고, 항속시간이 길어 해상에서 감시,첩보, 정찰 등에 효용성이 높으며, 최근 한척보다는 여러 척을 운용하는 것이 효과적이어서 무인선 군집(USV Swarm)으로 해상임무를 수행하려는 연구가 다양하게 진행되고 있다. 선박해양플랜트연구소에서는 2019년부터, 기존의 아라곤호 시리즈 무인선들을 활용하여, 무인선 군집 자율운항 시스템 개발을 위한 "인공지능 기반 무인선 상황인식 및 자율운항 기술 개발" 과제를 진행하고 있다. 해상에서 불법선박이 출현시 이를 효과적으로 단속하기 위하여 추적 기동이 필요한데, 본 연구에서는 무인선 3척을 활용하여 불법선박을 추적하는 해상 감시 실해역 시험을 수행하였다. 본 논문에서는 무인선 군집 자율운항 시스템에 대하여 소개하고, 무인선 군집을 활용한 불법선 추적에 관한 실해역 시험결과에 대해 소개한다.

• Journal of Navigation and Port Research
• /
• v.31 no.10
• /
• pp.813-818
• /
• 2007

There are the C.W.C and Towing Tank to the model-test equipments of the boat. A model testing of the high speed boat have a difficult in the performance verification because of very a small the scale-ratio of the ship-model and restricted by flow-velocity of the C.W.C and X-carriage velocity of the T.T. In general, the stepped hull boat is a high of fuel-efficiency because of the resistance reduction by a small wetted surface-area in correspond without stepped-hull boat. But It have a tendency to be bad the rolling performance by reduced stern wetted-area In this paper, the high speed stepped planning-boats with & without attached a stern body were performed to compare the effect of resistance and rolling performance by using sea model-test method.

• Journal of Navigation and Port Research
• /
• v.34 no.8
• /
• pp.623-628
• /
• 2010

High speed marine vehicle, such as semi-planing, planing craft have been developed recently. These ships paid attention to the resistance characteristics, especially in high speed region. Model test method is divided to two equipment greatly, first 'Towing tank', second 'C.W.C.'. It is difficult to estimate a resistance characteristics for high speed boat. because these are made for low speed ship. This paper suggests a new model test method and system. This is real sea model test and it's comprised of eight part. Firstly, This method is tested at C.W.C that is possible to using in real sea model tes using low speed boat modelt. And then, Real sea model test and CFD calculation are performed and compared with tow way used high speed boat model. It can be a good way to estimate a performance for high speed boat.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.29 no.6
• /
• pp.672-680
• /
• 2023

Weight is a critical factor in the ship design process given that it has a substantial impact on the hydrodynamic performance of ships. Typically, ships are optimally designed for specific conditions with a fixed draft and displacement. However, in reality, weight and draft can vary within a certain range owing to operational activities, such as fuel consumption, ballast adjustments, and loading conditions . Therefore, we investigated how resistance changes under three different loading conditions, namely overload, design-load, and lightship, for small craft, using both model experiments and numerical simulations. Additionally, we examined the sensitivity of weight changes to resistance to enhance the performance of ships, ultimately reducing power requirements in support of the International Maritime Organization's (IMO) goal of reducing CO2 emissions by 50% by 2050. We found that weight changes have a more significant impact at low Froude Numbers. Operating under overload conditions, which correspond to a 5% increase in draft and an 11.1% increase in displacement, can lead to a relatively substantial increase in total resistance, up to 15.97% and 14.31% in towing tests and CFD simulations, respectively.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.29 no.7
• /
• pp.971-979
• /
• 2023

Small ships (<499 GT) constitute 46% of the existing ships, therefore, it can be concluded that they produce relatively high CO₂ gas emissions. Operating in optimal trim conditions can reduce the resistance of the ship, which results in fewer greenhouse gases. An affordable way for trim optimization is to adjust the weight distribution to obtain an optimum longitudinal center of gravity (LCG). Therefore, in this study, the effect of LCG changes on the resistance of a small planing ship is studied using empirical and numerical analyses. The Savitsky method employing Maxsurf resistance and the STAR-CCM+ commercial computational fluid dynamics (CFD) software is used for the empirical and numerical analyses, respectively. Finally, the total resistance from the ship design process is compared to obtain the optimum LCG. To summarize, using numerical analysis, optimum LCG is achieved at the 46.2% length overall (LoA) at Froude Number 0.56, and 43.4% LoA at Froude Number 0.63, which provides a significant resistance reduction of 41.12 - 45.16% compared to the reference point at 29.2% LoA.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2018.11a
• /
• pp.220-221
• /
• 2018

배스보트는 주로 민물에서 낚시를 위해 설계되는 소형 고속 활주형 선박으로 국내에서도 수요가 높은 편이다. 하지만 경기에 참가하는 선수들이 선호하는 17ft급 이상의 배스보트에 대해서는 수입에 100% 의존하는 중이다. 본 연구에서는 18.5ft급 배스보트의 주요요목 결정 및 선형을 개발하고, 선저경사각을 결정하기 위해 상용 CFD코드인 STAR-CCM+ v10.04를 사용하여 수치해석을 수행하여 각 선저경사각별 항주자세 및 저항성능을 분석하여 최적의 선저경사각을 갖는 선형을 도출하였다.