• Journal of Korean Society of Steel Construction
• /
• 제11권2호통권39호
• /
• pp.213-222
• /
• 1999

Elastic-plastic methods have been used for the better prediction of the actual behavior of continuous-composite plate girder bridges in the overload and maximum load analysis. The structural evaluation using ALFD(Alternate Load Factor Design) uses the elastic-plastic analysis. The plastic rotations that remain after the load is removed can be occurred by the yielding locations of the maximum moment section. This situation can occur due to the residual stresses even if the moment is below the theoretical yield moment. The local yielding causes positive automoments that assure elastic behavior under subsequent overloads. In this study, the automoments at the piers occurred due to the unit plastic rotations and other locations were calculated by the conjugate-beam method and three-moment equation, using the nine design span with progressively smaller pier sections. The automoments were determined by the developed computer programs in this study in which the moments and plastic rotations from the continuity and moment-inelastic rotation relationships must be equal. And also the ratings of 3-span continuous composite plate girder bridges with non-compact section were carried out according to the Korean Highway Bridge Specification.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• 제34권7호
• /
• pp.911-917
• /
• 2010

In this study, we performed structural and fatigue analyses of the engine exhaust manifold that was subjected to thermo-mechanical cyclic loading. The methodologies used in this study are based on an approach in which the techniques for modeling the exhaust system, the temperature-dependent properties of the material, and thermal cyclic loading are taken into consideration and a reliable strategy is adopted for failure prediction. An application example shows that at an elevated temperature, considerable compressive plastic deformation is observed and that at a low temperature, tensile stresses remain in those parts of the test exhaust manifold where failure is observed. In order to predict fatigue life, mechanical damage is determined on the basis of the stress.strain hysteresis loops by using the classical Coffin.Manson equation and by adopting a method in which the dissipated plastic energy is taken into consideration.

• Journal of Korean Society of Steel Construction
• /
• 제15권4호통권65호
• /
• pp.369-378
• /
• 2003

This study proposed a damage index for steel members and examined a process where steel square tubular columns under cycle loading failed to meet the damage index. A nonlinear analysis was carried out and a damage process analyzed using a finite element program. Material properties and strain characteristics were obtained from material testing. The effect on the damage of members was analyzed according to varying kinds of steels and conditions of loading based on material testing results. According to strain characteristics and cumulative plastic strain of each variable, the effect of conditions of loading and kinds of steels on the damage could be estimated quantitatively.

• Transactions of the Korean Society of Mechanical Engineers
• /
• 제19권9호
• /
• pp.2165-2172
• /
• 1995

Optimization of mesh discretization has been proposed to improve the accuracy of limit analysis solution of collapse load by using the Rigid Body Spring Model(R. B. S. M) under the plane strain condition. Moreover, the fracture behaviour of materials was investigated by employing the fracture mechanism of a spring connecting the triangular rigid body element. It has been clarified that the collapse load and the geometry of slip boundary for optimized mesh discretization were close to those of the slip line solution. Further, the wedge-shaped fracture of a cylinder under a lateral load and the central fracture of a strip in the drawing process were well simulated.

• Proceedings of the Korea Concrete Institute Conference
• /
• 한국콘크리트학회 2009년도 춘계 학술대회 제21권1호
• /
• pp.11-12
• /
• 2009

The small height to depth ratio column dominated by shear after tension steel yielded and the energy dissipation capacity reduce remarkably due to the affection of axial force. This procedure incur in the plastic hinge region and not in all of the region at the same time but from somewhere where the energy was concentrated. This study was reported about the variation of length of the plastic hinge under cyclic loading of the RC columns through the test.

• Proceedings of the Korean Nuclear Society Conference
• /
• 한국원자력학회 1996년도 춘계학술발표회논문집(4)
• /
• pp.235-240
• /
• 1996

본 연구에서는 고온의 천이 열하중을 받는 304 SS 재질의 액체금속로 원통용기에 대하여 진행성 변형기구인 열적 라체팅(thermal ratcheting) 변형거동을 해석하였다. 재료의 반복 소성을 나타내는 구성식으로서 Chaboche모델을 이용하였으며 이 모델의 적용을 위하여 ABAQUS의 사용자 프로그램을 개발하였다. 열천이 과정이 반복되는 동안에 축방향의 온도분포 이동에 따른 탄소성 해석을 수행한 결과 소성변형이 각 싸이클마다 누적되어 점진적 변형이 일어났으며 이 해석결과를 시험치와 비교함으로써 해석의 타당성을 검토하였다. 반복 소성거동에 대한 Chaboche 모델을 이용하면 천이 열하중을 받는 304 SS. 재질의 고온구조물에 대하여 라체팅 거동을 정량적으로 평가 할 수 있는 것으로 나타났다.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• 제22권6호
• /
• pp.565-572
• /
• 2009

This work intends to establish the reliability and fracture toughness $K_{IC}$ criterion of welded joints by EGW for high strength EH36-TMCP ultra thick plate. For this, firstly thermo elasto-plastic analysis has been carried out on two pass X-groove butt joint model to clarify the thermal and mechanical behaviour(residual stress, plastic strain, magnitude of stress and their distribution and production mechanism). Moreover, to establish fracture criterion, analysis of fracture toughness $K_{IC}$ has been performed under the notch machined and residual stress with the load condition on EGW welded joints. A quantitative fracture criterion for EGW welded joints is suggested by using $K_{IC}$.

• Journal of the Society of Disaster Information
• /
• 제15권2호
• /
• pp.186-197
• /
• 2019

Purpose: This study intends to develop a nonlinear cyclic plasticity damage model in the framework of finite element formulation, which is capable of taking large deformation effects into account, in order to accurately predict the hysteretic behavior of stainless steel structures. Method: The new cyclic constitutive equations that utilize the combined isotropic-kinematic hardening rule for plastic deformation is incorporated into the damage mechanic model in conjunction with the large strain formulation. The damage growth law is based on the experimental observations that the evolution of microvoids yields nonlinear damage accumulation with plastic deformation. The damage model parameters and the procedure for their identification are presented. Results and Conclusion: The proposed nonlinear damage model has been verified by simulating uniaxial strain-controlled monotonic and cyclic loading tests, and successfully applied to a thin-walled stainless steel pipe subjected to constant and alternating strain-controlled cyclic loadings.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 한국재료학회 2003년도 춘계학술발표강연 및 논문개요집
• /
• pp.244-244
• /
• 2003

나노인덴테이션은 시편에 압자를 침투시켜 재료의 기계적 특성을 파악할 수 있는 경도시험법이다. 압입범위를 나노미터범위로 조절할 수 있어 기존에 접근할 수 없었던 극 미소부분에로 응용이 넓어지고 있다. 경도시험시 재료의 탄성 및 소성 작용에 의해 재료는 변형되고, 표면변화 관찰을 통해 표면아래 부분에서 이루어지고 있는 거동을 예측할 수 있다. 이러한 관점에서 나노인덴테이션 시험시에도 발생하는 파일업과 싱크인 현상에서 재료가 나노미터 범위에서 어떠한 양상으로 변형을 하는지를 고찰하는 것은 의미가 있을 것이다. 본 연구에서 파일업과 싱크인의 양상을 파악하고 그 양을 정량화하기 위하여 가공경화양에 따른 표면변화와 압입하중 변화에 따른 표면변화를 관찰하였다. 어닐링한 봉상 알루미늄을 압축변형을 0%, 5%, 20%, 40%, 50% 로 변형시켜 가공경화를 일으켰고, 표면은 전해연마하여 나노압입시험이 가능하도록 하였다. 각각의 시편을 나노인덴테이션 압입하중을 변화시켜 재료에서 하중 변화에 따라 나타나는 표면변화를 관찰하였고, 위의 각 조건에서 파일업양을 정량화 하였다. 연구결과에 대해 ANSYS 유한요소분석 프로그램을 사용하여 재료의 변형양상을 시뮬레이션 하였고, 실제 실험데이터와 비교 분석하였다.

• Transactions of Materials Processing
• /
• 제1권2호
• /
• pp.52-62
• /
• 1992

본 연구에서는 모델재료를 이용한 모사실험을 통하여 고온의 강을 단조하였을 때의 유동과 변형 그리고 하중을 검토하고, 이어 성형에 관한 연구를 하였다. 모델재료인 플라스티신은 고용의 강을 모사하는데 많이 쓰이는데, 실험을 통하여 플라스티신과 강과의 변형저항식을 비교 검토하였다. 이 실험결과 상사성이 어느정도 일치함을 알았고, 이 상사성 결과를 이용하여 실제와 모델사이의 하중과 응력비를 검출하였다. 이로써 플라스티신을 이용한 단조 압축 실험을 통하여 실제의 하중을 예측하였다. 또한 예비 성형체를 설계하기 위하여 앞서 실험한 결과들을 이용하여 초기의 실린더의 체적과 치수를 결정하고 이에 단계에 따른 성형과정을 통하여 예비 성형체를 만들었는데, 이는 제한된 용량으로 성형하여야 하는 문제를 해결하기 위함이었다. 실험 결과 8단계에 따른 성형과정에 의해 우리가 원하는 대형 단조품을 성형할 수 있음을 알았다.