• Korean Journal of Optics and Photonics
• /
• v.31 no.2
• /
• pp.71-80
• /
• 2020

In this article, we suggest a new method for measuring an aerosol's extinction coefficient using a commercial camera. For a given image, we choose three pixel-points that are imaged for the same kinds of objects located in similar directions. We suggest and calculate aerosol extinction coefficients from these RGB gray levels and the different distances of the three objects. To compare our measurement results, we also measure extinction coefficients using lidar. Finally, we find that there are meaningful and sensible correlations between these two measurements, with a correlation coefficient of 0.86. We measure the aerosol extinction coefficient at three different RGB wavelengths using the same method. From these aerosol extinction coefficients at three different wavelengths, we find that the Angstrom exponent ranges from 0.7 to 1.6 over a full daytime period. We believe that these Angstrom exponents can give important information about the size of the fine particles.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.27 no.6
• /
• pp.86-93
• /
• 2023

As the hysteretic behavior of reinforced concrete members under cyclic loading progresses, the energy dissipation ability decreases due to a decrease in stiffness and strength and pinching effects. However, the guideline "Nonlinear Analysis Model for Performance-Based Seismic Design of Reinforced Concrete Building Structures, 2021" requires calculating a single energy dissipation factor for each member and all histeric step, so the decrease in energy dissipation capacity according to histeric step cannot be considered. It is judged that Therefore, in this study, the energy dissipation factor according to the histeric step was examined by comparing the existing experimental results and the nonlinear time history analysis results for a general beam under cyclic loading. The energy dissipation factor was calculated as the ratio of the energy dissipation amount of the actual specimen to the energy dissipation amount of the idealized elastoplastic behavior obtained as a result of nonlinear time history analysis. In the existing experiment results, the energy dissipation factor was derived by calculating one cycle for each histeric step, and the energy dissipation factor was derived based on the nonlinear modeling process in the guidelines. In the existing experimental study, the energy dissipation factor was calculated by setting each histeric step (Y-L-R), and the energy dissipation factor was found to be 0.36 in the Y-L step and 0.28 in the L-R step, and the energy dissipation factor in the guideline was found to be 0.31. This shows that the energy dissipation factor calculation formula in the guidelines does not indicate a decrease in the energy dissipation capacity of reinforced concrete members.

• Journal of the Korean Geotechnical Society
• /
• v.17 no.5
• /
• pp.43-50
• /
• 2001

딜라토메터는 실험의 간편성, 경제성, 신속성 및 반복성 등을 바탕으로 현장에서의 지반공학적 물성추정에 보편화되고 있다. 또한 간단한 장비구성과 손쉬운 사용법에도 불구하고 다양한 지반공학적 물성들 -예로서, $K_{o}$ , OCR, $c_{u}$ , $\psi$, $c_{h}$, $k_{h}$, ${\gamma}$, M, $u_{o}$ -을 추정할 수 있으며 다양한 지반공학적 설계문제에 성공적으로 적용되어 왔다. 그러나 제안된 관계식들이 대부분 기존실험 결과들과의 비교를 통하여 얻어진 경험적 상관관계이며, 특히 압밀계수 추정에 관한 부분은 관입시 평면변형 상태의 지반변형으로 인한 관입모사의 복잡성으로 인하여 피에조콘 소산시험 해석을 위해 제안된 이론 해들에 경험적인 가정사항들을 추가하여 사용하는 반경험적 방법들과 순수한 경험적인 방법이 사용되어 왔다. 본 연구에서는 elf라토메터 관입기의 실제 평면적을 등가의 원형반경으로 고려한 등가반경을 사용하고 최적화기법을 적용함으로써, 소산시험에서 실제 관측된 간극수압($p_2$)과 딜라토메터 소산시험을 모사하여 얻어진 예측 간극수압의 차이를 최소화하는 수평압밀계수 추정법을 제안하였다. 제안된 방법을 국내 양산지역에서 수행된 딜라토메터 소산실험에 적용하였으며 추정된 수평압밀계수 값을 기존의 딜라토메터 수평압밀계수 추정법들과 불교란 시료를 이용한 일차원 실내 압밀실험으로 얻어진 수평압밀계수 값들과 비교검증 하였다. 그 결과 제안된 방법으로 기존의 방법에 비해 실내 압밀실험 결과와 일치하는 수평압밀계수 추정결과를 얻었다. 또한, 제안된 방법으로 얻어진 수평압밀계수는 전 소산도 범위에서 고르게 관측값과 일치하는 소산곡선을 예측하여, 최적화기법을 이용한 딜라토메터 소산시험 해석으로 전 소산과정을 대표하는 압밀계수의 추정이 가능할 것으로 사료된다.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.23 no.5
• /
• pp.409-417
• /
• 2003

Cure monitoring can be used to improve the quality and productivity of thermosetting resin matrix composite products during their manufacturing process. In this work, the sensitivity of dielectrometry was improved by adequate separation the efforts of sensor and externals on the measured signal. A new algorithm to obtain the degree of cure during dielectric cure monitoring of glass/polyester and glass/epoxy composites was developed by employing a function of both temperature and dissipation factor, in which five cure monitoring parameters were used to calculate the degree of cure. The decreasing pattern of dissipation factor was compared with the relationships between the degree of cure and the resin viscosity. The developed algorithm might be employed for the in situ cure monitoring of thermosetting resin composites.

• Journal of the Korean Geotechnical Society
• /
• v.20 no.3
• /
• pp.151-159
• /
• 2004

This paper describes a systematic way of identifying the horizontal coefficient of consolidation of clayey soil by applying an optimization technique to the early part of dissipation data measured from the self-boring pressuremeter strain holding test. An analytical solution developed by Randolph ＆ Wroth (1979) was implemented in normalized form to express the build-up of excess pore pressures as a function of the rigidity index and subsequent dissipation of excess pore pressures around a pressuremeter Horizontal coefficient of consolidation was determined by minimizing the differences between theoretical and measured excess pore pressure curves over 50% degree of dissipation range using optimization technique. The effectiveness of the proposed back-analysis method was examined against the real fled performances obtained from pressuremeter strain holding tests at Gimje and Yangsan site. It is shown that the proposed back-analysis method can evaluates the rational horizontal coefficient of consolidation, which is similar to those obtained from the piezocone dissipation test. Furthermore, proposed method can evaluate appropriate coefficient of consolidation for soil under partially drained condition.

• Journal of the Korean Geotechnical Society
• /
• v.19 no.6
• /
• pp.363-369
• /
• 2003

The purpose of this study is to understand the dissipation pattern of excess pore pressure after liquefaction and to estimate the variation in permeability during shaking load, which should be known for settlement predictions of the ground undergoing liquefaction. In this study, 1-g shaking table tests were carried out for 5 different kinds of sands, all of which had high liquefaction potentials. During the tests excess pore pressure at various depths, and surface settlements were measured. The measured dissipation curve of the excess pore pressure after liquefaction was linearly simulated using the solidification theory, and from the analysis of the slopes of linearly simulated curves, the correlation between dissipation velocity and the gradation characteristics was obtained. By substituting this correlation and the measured settlement to the dissipation velocity equation recommended in solidification theory, the permeability during dissipation was calculated, which was used for estimating the permeability variation during shaking load. The dissipation velocity of excess pore pressure after liquefaction had a linear correlation with the effective grain size divided by the coefficient of uniformity. The permeability during dissipation and liquefaction increased by 1.1∼2.8 times and 1.4∼5 times compared to the initial permeability of the original ground, respectively. And the amount of increase became greater as the effective grain size of the test sand increased and the coefficient of uniformity decreased.

• Composites Research
• /
• v.16 no.4
• /
• pp.51-58
• /
• 2003

Since the reliability of adhesively bonded joints is much dependent on the curing status of thermosetting adhesive, the on-line cure monitoring during the cure of adhesively joints could improve the quality of adhesively bonded joints. In this work, the dielectric method which measures the dissipation factor of the adhesive during the cure of joints and converts it into the degree of cure of the adhesive was devised. The relation between the dissipation factor and the degree of cure of adhesive was investigated, which could eliminate the temperature effect on the dissipation factor that is a strong function of the degree of cure and temperature of adhesive. From the investigation, it was found that the dissipation factor showed a trend similar to the cure rate of the adhesive.

• Journal of the Korean Geotechnical Society
• /
• v.19 no.5
• /
• pp.145-154
• /
• 2003

In this study, the variation in excess pore pressure during dissipation is estimated by using successive cavity expansion theory and finite difference technique based on axisymmetric uncoupled linear consolidation theory with separate consideration of magnitude and initial distribution $\Delta{u}_{oct}$induced by changes of octahedral normal stress, and $\Delta{u}_{shear}$ induced by changes of octahedral shear stress. The coefficient of consolidation is also estimated by trial and error procedure until the predicted dissipation curve matches the measured curve at a typical degree of dissipation. The proposed method is applied to the results of miniature piezocone tests at Louisiana State University calibration chamber system. Based on the results of interpretation and the comparison with experimental measurements and those from other solutions, the prediction dissipation curves show a good match with those measured during dissipation tests and the values of coefficient of consolidation estimated by proposed method are more close to the range of laboratory measurements than those of other theories.

• Journal of the Korean Geotechnical Society
• /
• v.17 no.4
• /
• pp.153-160
• /
• 2001

딜라토메터를 이용한 현장 수평압밀계수 추정법의 국내 점토지반 및 실트질 지반에의 적용성을 평가하기 위해 국내 점토지반과 실트지반에 대하여 각각 딜라토메터 관입시험 및 소산시험을 수행하였다. 소산시험 결과로부터 DMT-C법 [p$_2$-log t법과 C-√t법]과 DMT-A법을 이용하여 수평압밀계수를 추정하여 상호 비교하였으며 다른 실험방법에서 얻어진 결과들과도 함께 비교하고 평가하였다. 비교대상으로는 동일지반의 현장 피에조콘 소산시험으로 얻어진 수평압밀계수 및 불교란시료에 대하여 수행된 로셀압밀실험 및 일차원 실내압밀실험 결과가 함께 이용되었다. 연구결과 C-√t법을 제외한 p$_2$-log t법과 DMT-A법은 국내 점토지반에 대하여 상호일치하는 결과를 줄 뿐 아니라 피에조콘 결과와도 비교적 잘 일치하는 수평 압밀계수를 측정하였으며 다른 결과와 비교할 때 신뢰성 있는 결과를 주었다. 그러나 실트질 지반에 대하여는 p$_2$-log t법만이 적용 가능할 것으로 판단된다.

• Journal of the Korean Geotechnical Society
• /
• v.19 no.4
• /
• pp.311-320
• /
• 2003

The coefficient of consolidation of clay deposit is one of the most important properties in the design of ground improvement. The in-situ value of $c_h$ is generally estimated by pore pressure dissipation using piezocone. Many researchers have suggested theoretical formula for its estimation. This study attempts to find out the validity of the existing theoretical formula in Korea and to find out the characteristics of $c_h$ related to the mechanical properties of clay. Piezocone tests and laboratory tests were performed at the site of pilot project of ground improvement at Yangsan-Mulgeum, Gyeongnam. Comparison of the estimated values of $c_h$using piezocone tests results and those from laboratory consolidation tests are carried out. Results show that Torstensson(cylindrical cavity theory) and Teh & Houlsby solutions derive similar values of $c_h$. And $c_h$ from oedometer test shows values similar to the above two methods. The value from either of the above two methods[Torstensson(cylindrical) or Teh & Houlsby] is recommended to be used as $c_h$.