• Journal of the Korea institute for structural maintenance and inspection
• /
• v.26 no.4
• /
• pp.57-64
• /
• 2022

Chloride, which is one of the main deterioration factors in reinforced concrete structures, can degrade the performance of the structure due to chloride-induced corrosion of steel. Chloride content at steel depth or the rate of chloride penetration is necessary to determine deterioration of reinforced concrete or to calculate initiation time of steel corrosion caused by chloride attack. Chlorides in concrete are generally identified with typical two methods including chloride profiling using potentiometric titration method and discoloration method using AgNO₃ solution. The former is advantageous to estimate chloride penetration rate (diffusion coefficient in general) with measured chloride contents directly, but it is laborious. In the case of latter, while the result is obtained easily with the range of discoloration, the error may occur depending on workmanship when the depth of chloride ingress is measured. This study shows that chloride penetrated depth is evaluated with the results obtained from discoloration method through image analysis, thereby the error is minimized by workmanship. In addition, the effect of micro-crack in concrete is studied on chloride penetration. In conclusion, the depth of chloride penetration was quantified with image analysis and as it was confirmed that chlorides can rapidly penetrate through micro-cracks, caution is especially required for cracks in concrete structure.

• Journal of Navigation and Port Research
• /
• v.46 no.6
• /
• pp.562-569
• /
• 2022

The alarm monitoring technology applied to existing operating ships manages data items such as temperature and pressure with AMS (Alarm Monitoring System) and provides an alarm to the crew should these sensing data exceed the normal level range. In addition, the maintenance of existing ships follows the Planned Maintenance System (PMS). whereby the sensing data measured from the equipment is monitored and if it surpasses the set range, maintenance is performed through an alarm, or the corresponding part is replaced in advance after being used for a certain period of time regardless of whether the target device has a malfunction or not. To secure the reliability and operational safety of ship engine operation, it is necessary to enable advanced diagnosis and prediction based on real-time condition monitoring data. To do so, comprehensive measurement of actual ship data, creation of a database, and implementation of a condition diagnosis monitoring system for condition-based predictive maintenance of auxiliary equipment and piping must take place. Furthermore, the system should enable management of auxiliary equipment and piping status information based on a responsive web, and be optimized for screen and resolution so that it can be accessed and used by various mobile devices such as smartphones as well as for viewing on a PC on board. This update cost is low, and the management method is easy. In this paper, we propose CBM (Condition Based Management) technology, for autonomous ships. This core technology is used to identify abnormal phenomena through state diagnosis and monitoring of pumps and purifiers among ship auxiliary equipment, and seawater and steam pipes among pipes. It is intended to provide performance diagnosis and failure prediction of ship auxiliary equipment and piping for convergence analysis, and to support preventive maintenance decision-making.

• Journal of the Korea Society of Computer and Information
• /
• v.27 no.11
• /
• pp.181-190
• /
• 2022

In this paper, we use a LiDAR sensor and an image camera to detect a left-turning waiting vehicle in two ways, unlike the existing image-type or loop-type left-turn detection system, and a left-turn traffic signal corresponding to the waiting length of the left-turning lane. A system that can efficiently assign a system is introduced. For the LiDAR signal transmitted and received by the LiDAR sensor, the left-turn waiting vehicle is detected in real time, and the image by the video camera is analyzed in real time or at regular intervals, thereby reducing unnecessary computational processing and enabling real-time sensitive processing. As a result of performing a performance test for 5 hours every day for one week with an intersection simulation using an actual signal processor, a detection rate of 99.9%, which was improved by 3% to 5% compared to the existing method, was recorded. The advantage is that 99.9% of vehicles waiting to turn left are detected by the LiDAR sensor, and even if an intentional omission of detection occurs, an immediate response is possible through self-correction using the video, so the excessive waiting time of vehicles waiting to turn left is controlled by all lanes in the intersection. was able to guide the flow of traffic smoothly. In addition, when applied to an intersection in the outskirts of which left-turning vehicles are rare, service reliability and efficiency can be improved by reducing unnecessary signal costs.

• KIPS Transactions on Software and Data Engineering
• /
• v.11 no.8
• /
• pp.339-346
• /
• 2022

Recently, the resource depletion and climate change problem caused by the massive usage of fossil fuels for electric power generation has become a critical issue worldwide. According to this issue, interest in renewable energy resources that can replace fossil fuels is increasing. Especially, photovoltaic power has gaining much attention because there is no risk of resource exhaustion compared to other energy resources and there are low restrictions on installation of photovoltaic system. In order to use the power generated by the photovoltaic system efficiently, a more accurate photovoltaic power forecasting model is required. So far, even though many machine learning and deep learning-based photovoltaic power forecasting models have been proposed, they showed limited success in terms of interpretability. Deep learning-based forecasting models have the disadvantage of being difficult to explain how the forecasting results are derived. To solve this problem, many studies are being conducted on explainable artificial intelligence technique. The reliability of the model can be secured if it is possible to interpret how the model derives the results. Also, the model can be improved to increase the forecasting accuracy based on the analysis results. Therefore, in this paper, we propose an explainable photovoltaic power forecasting scheme based on BiLSTM (Bidirectional Long Short-Term Memory) and SHAP (SHapley Additive exPlanations).

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.67 no.4
• /
• pp.274-284
• /
• 2022

To use kenaf (Hibiscus cannabinus L.) as a fiber and livestock feed, a high-yielding variety needs to be identified. For this, accurate phenotyping of plant height is required for this breeding purpose due to the strong relationship between plant height and yield. Plant height can be estimated using RGB images from unmanned aerial vehicles (UAV-RGB) and photogrammetry based on Structure from Motion (SfM) algorithms. In kenaf, accurate measurement of height is limited because kenaf stems have high flexibility and its height is easily affected by wind, growing up to 3 ~ 4 m. Therefore, we aimed to identify a method suitable for the accurate estimation of plant height of kenaf and investigate the feasibility of using the UAV-RGB-derived plant height map. Height estimation derived from UAV-RGB was improved using multi-point calibration against the five different wooden structures with known heights (30, 60, 90, 120, and 150 cm). Using the proposed method, we analyzed the variation in temporal height of 23 kenaf cultivars. Our results demontrated that the actual and estimated heights were reliably comparable with the coefficient of determination (R²) of 0.80 and a slope of 0.94. This method enabled the effective identification of cultivars with significantly different heights at each growth stages.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.34 no.1
• /
• pp.1-7
• /
• 2024

β-Ga₂O₃ is a material with a wide band gap of ~4.8 eV and a high breakdown-voltage of 8 MV/cm, and is attracting much attention in the field of power device applications. In addition, compared to representative WBG semiconductor materials such as SiC, GaN and Diamond, it has the advantage of enabling single crystal growth with high growth rate and low manufacturing cost [1-4]. In this study, we succeeded in growing a 10 mm thick β-Ga₂O₃ single crystal doped with 0.3 mol% SnO₂ through the EFG (Edge-defined Film-fed Growth) method using multi-slit structure. The growth direction and growth plane were set to [010]/(010), respectively, and the growth speed was about 12 mm/h. The grown β-Ga₂O₃ single crystal was cut into various crystal planes (010, 001, 100, ${\bar{2}}01$) and surface processed. The processed samples were compared for characteristics according to crystal plane through analysis such as XRD, UV/VIS/NIR/Spec., Mercury Probe, AFM and Etching. This research is expected to contribute to the development of power semiconductor technology in high-voltage and high-temperature applications, and selecting a substrate with better characteristics will play an important role in improving device performance and reliability.

• Knowledge Management Research
• /
• v.25 no.1
• /
• pp.43-66
• /
• 2024

In an era where digital technology reshapes brand-consumer interactions, this study examines the influence of Nike's Run Club and Adidas' Runtastic apps on loyalty and advocacy. Analyzing 3,715 English reviews from January 2020 to October 2023 through text mining, and conducting a focused sentiment analysis on 155 'recommend' mentions, we explore the nuances of 'hot loyalty'. The findings reveal Nike as a 'companion' with an emphasis on emotional engagement, versus Runtastic's 'tool' focus on reliability. This underscores the varied consumer perceptions across similar platforms, highlighting the necessity for brands to integrate user preferences and address technical flaws to foster loyalty. Demonstrating how customized technology adaptations impact loyalty, this research offers crucial insights for digital brand strategy, suggesting a proactive approach in app development and management for brand loyalty enhancement

• The Journal of the Convergence on Culture Technology
• /
• v.10 no.1
• /
• pp.289-295
• /
• 2024

This study analyzes the correlation between the accracy of rifle and the result of engagement. And estimates the improvement cost of the rifle accordingly. For this experiment, an engagement class simulation model(AWAM: Army Weapon Effectiveness Analysis Model) was used. We also selected the rifle, which is a portable weapon for the experiment. Prior to this experiment, we conducted a reliability test(VV&A: Verification, Validation and Accreditation) on the model. The VV&A process is mainly done during the development of the DM&S model, which is also necessary for the operation of the M&S. We confirmed the need for VV&A during the experiment and obtained reliable experimental results using the corrected values. In the Accuracy Experiment we found that the 20% improvement is the most effective. And we were able to estimate the cost of acquiring a rifle with a 20% higher accuracy. The cost was estimated by simple regression analysis based on the price of the current rifle. Through this study, we could know the impact of the accuracy of rifle on the experimental results and estimate the cost of improved rifle.

• The Journal of the Convergence on Culture Technology
• /
• v.10 no.1
• /
• pp.585-590
• /
• 2024

In this study, rail surface defects are increasing due to the aging of urban railway rails, but in the detailed guidelines for track performance evaluation established by the country, rail surface damage is inspected with the naked eye of engineers and simple measuring tools. With the recent enactment of the Track Diagnosis Act, a large budget has been invested and the volume of rail diagnosis is rapidly increasing, but it is difficult to secure the reliability of diagnosis results using labor-intensive visual inspection techniques. It is very important to discover defects in the rail surface through periodic track tours and visual inspection. However, evaluating the severity of defects on the rail surface based on the subjective judgment of the inspector has significant limitations in predicting damage inside the rail. In this study, the rail internal crack characteristics due to rail surface damage were studied. In field measurements, rail surface damage locations were selected, samples of various damage types were collected, and the rail surface damage status was evaluated. In indoor testing, we intend to analyze the correlation between rail surface defects and internal defects using a electron scanning microscope (SEM). To determine the crack growth rate of urban railway rails currently in use, the Gaussian probability density function was applied and analyzed.

• Journal of Navigation and Port Research
• /
• v.48 no.4
• /
• pp.249-260
• /
• 2024

This paper aimed to summarize research on technologies that could efficiently reduce wave-making resistance of container ships. Tto develop wave resistance reduction technology that could be applied to container ships and use it in real ship design, hull-form optimal design was performed by applying optimization algorithms, hull-form change algorithms, ship performance prediction algorithms, automation algorithms, and iterative optimal design techniques. A computer program was also developed. To properly set design variables known to be important elements in hull-form optimal design and to efficiently set lower and upper limits of design variables, a sensitivity analysis algorithm was developed and applied to hull-form optimal design. To predict the reliability and applicability of the developed computer program for real ships, hull-form optimal design was performed for a KRISO Container Ship (KCS), a container ship with various studies conducted worldwide. Hull-form optimal design was performed at Fn=0.26, the design speed of the KCS ship. Numerical analysis was performed on the hull-form of the target ship, the KCS ship, and the hull-form of the ship derived as a result of the hull-form optimal design to determine wave resistance, wave system, and wave height. The optimal ship's wave resistance was found to be reduced by 80.60% compared to the target ship. The displacement and wetted surface area were also found to be reduced by 1.54% and 1.21%, respectively.