• The Korean Journal of Rheology
• /
• v.8 no.2
• /
• pp.92-102
• /
• 1996

두 종류의 열방성 액정고분자와 세종류의 엔지니어링 고분자와의 블렌드들에 대해 유변학적/형구학적 연구를 한 결과 블렌드의 유동거동과 물성이현저히 다른 두 그룹으로 나 뉘어짐을 발견하였다. 즉 연속상의 조업온도가 분산상의 전이온도보다 높은 그룹A에 속하 는 블렌드의 전단점도/신장점도는 액정고분자를 첨가할수록 첨가할수록 감소하고 블렌드의 신장점도는 연속상의 그것처럼 신장변형률속도가 커질수록 증가하였다. 또한 분산상의 점도 가 연속상의 그것보다 작아서 분산상이 미세섬유구조의 형태로 존재하였다. 이와 대조적으 로 연속상의 조업온도가 액정고분자의 전이온도보다 낮은 그룹 B에 속하는 블렌드는 반대 의 거동을 보였고 분산상의 미세섬유구조가 존재하지 않았다. 그러나 연신변형이 주가 되는 방사공정을 거치면 그룹A와 B블렌드 공히 분산상이 비슷한 미세섬유구조의 형태로 존재하 고 기계적 성질도 크게 향상되는 결과를 보였다. 이는 블렌드내의 신장유동이 분산상의 섬 유구조형상에 결정적 역할을 하기 때문이라 판단된다.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.23 no.1
• /
• pp.111-119
• /
• 1999

가수분해된 네 개의 반응성 염료를 이용하여 견, 양모 나일론 섬유를 염색할 때 영향을 미치는 여러 인자들에 대하여 연구하였다 염의 투입을 가수분해 전과 후로 달리하였을 때 염색된 직물의 K/S 값에 미치는 영향은 염료와 직물의 종류에 따라 각기 달랐으며 염의 영향은 염료의 분자 크기가 클 때 더 크게 나타났다. 이는 염 노동의 증가시 염욕 안에서의염료 용해도가 염료 분자가 클 때 더많은 영향을 받기 때문인 것으로 생각된다. 욕비 증가시에는 염색된 직물의 K/S값은 초기에 감소를 보이다가 높은 욕비에서 K/S값이 증가되었는데 이는 염의 농도의 감소로 인한 영향으로 사료된다. 가수분해된 반응성 염료로 염색된 직물의 수세 견뢰도는 염료의 분자 크기에 의해 영향을 받았으며 직물의 마찰 땀 견괴도는 Gray scale에서 3보다 높았다 본 연구의 결과는 면섬유 염색에 사용한 가수분해된 반응성 염료를 이용하여 견, 양모, 또는 나일론섬유의 염색에 재 사용할 수 있는 가능성을 제시하여 준다.

• Journal of the KSME
• /
• v.22 no.1
• /
• pp.9-14
• /
• 1982

복합재료를 이용하여 부품제작을 한 후 어떠한 결합방법을 채택할 것인가를 결정할 때 고려해 야할 점을 기계적 결합법과 접착결합법을 비교하여 검토하였다. 기계적 결합은 하중을 많이 받고 분해 및 결합이 자주 예상되는 부품에 채택해야 할 것이며 복합재료의 특성을 고려하여 보강 시에 부착하는 평판의 섬유방향은 가급적 드릴구멍주위를 부드럽게 하여 응력집중을 낮출 수 있으며 하중의 종류에 따라 적층의 섬유방향을 조절함으로서 응력집중을 조절할 수 있다. 드릴 구멍 주위인 파손은 평판의 폭과 구멍의 직경등이 크게 작용함으로 강도해석을 할 경우에 응력 해석을 한 후 허용응력등을 결정해야할 것이다. 접착졀합법은 작업이 간단하나 신뢰도가 떨어지 므로 하중을 많이 받는 구조물에의 사용에 주의를 요하며 설계방법도 매우 다양하게 제안되어 있어 선택함에 있어 하중 환경조건등을 점검해야할 것이다. 접착결합법은 드릴구멍같은 불연속 성을 갖지 않기 때문에 응력집중이 생기지 않으나 접착층의 길이등 기하학적 형상에 따라 다르게 나타남으로 잡착층의 분리가 일어나지 않도록 설계되어야 한다. 특히 복합재료의 이방성인 성 질을 감안하여 접착층에 이웃하는 피접착층의 섬유방향에 주의해야 하며 층간응력이 파손에 미 치는 영향을 고려하여 설계에 임해야 한다.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2013.11a
• /
• pp.38-39
• /
• 2013

In this study, in regard to fiber reinforced mortar mixing steel fiber and 4types of organic fiber, impact test was carried out. Because to predict fracture reduction performance with flexural, tensile strength when types of fiber were different as impact reduction performance of concrete is closely related with toughness such as flexural strength, tensile strength and fracture energy etc. As a result, enhancement of toughness by fiber reinforcement controls the spall of rear. On the other hand in case of steel fiber relatively turned up high toughness in appropriate load compared with organic fiber but in same mixing rate, impact reduction performance by projectile showed low performance due to few number of an individual of mixing.

• Journal of Korean Society on Water Environment
• /
• v.27 no.3
• /
• pp.329-333
• /
• 2011

p-phenylene-2,5-benzobisoxazole (PBO; Zylon$(R)$) fibers as an adsorbent were employed for solid phase extraction of aqueous alkylphenols. The removal ratios for 10 kinds of alkylphenols at initial concentration of $100{\mu}gL^{-1}$ were in the range of 16.8-96.3% and the removals increased with the increase of the phase ratio (fiber weight/solution volume). The plots of the logarithm of partition coefficient (log K) were correlated with the logarithm of the n-octanol/water partition coefficient (log P). The adsorbed alkylphenols were completely desorbed with the mixture of acetonitrile and dichloromethane.

• Korean Journal of Materials Research
• /
• v.7 no.2
• /
• pp.121-128
• /
• 1997

Two-types of carbon fiber, anisotropic- and isotropic- pitch based, were expose to isothermal oxidation in air and $CO_{2}$ gas and the weight change rates was measured by TGA apparatus. Thc oxidation rate was laster in air than in $CO_{2}$ gas, and the oxidation rare of isotropic T- 101s liher was over 23 9 times faster than that of anisotropic HM-60 filler at $600^{\circ}C$ in air. The activation energy was 36-56 Kcal/mole at lower temperature range and 6- 13 Kcal/molc at higher temperature range. It was higher that the transition temperalure 01 reaction zone(zone 1. 2, :i) of 11M-GO fiber than that of T-101s fiber, and it was higher in $CO_{2}$ gas than in air. From SEM observation, it Lvas found that the oxidation of carbon fibers was progressed through the imperfection.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.17 no.3
• /
• pp.283-293
• /
• 2015

In order to evaluate corrosion resistance of steel fiber-reinforced concrete, accelerated chloride migration and surface resistivity tests were conducted. In addition air content of fresh concrete, compressive strength and water absorption were measured for investigating fundamental characteristics of concrete. Two different water-cement ratios(0.44, 0.5) and three steel fiber contents(0.25%, 0.5%, 1%) were considered as variables. Note that all specimens cast with same compaction work. As a results, corrosion resistance decreased as steel fiber contents increased regardless of water-cement ratio when the concrete was compacted with same amount of work done. However, for concrete with same steel fiber content, the lower water-cement ratio showed the better corrosion resistance. It is found that enhancement of fluidity and enough compaction should be done for corrosion resistance of SFRC.

• Composites Research
• /
• v.29 no.5
• /
• pp.293-298
• /
• 2016

In this paper, Glass Fiber Reinforced Thermoplastic (GFRTP) for automotive headlight source module was fabricated by compounding and injection molding using PPS (Poly Phenylene Sulfide) resin with glass fiber which has three cross section (round type, cocoon type, flat type). Tensile, flexural, impact properties were investigated on effect of cross section, glass fiber contents. And it was observed flatness, dimensional stability, fluidity depending on glass fiber cross section. As a result, flat glass fiber reinforced thermoplastic's mechanical properties were most excellent. Also, dimensional stability and flatness showed better results when using flat glass fiber.

• Journal of the Korean Society for Railway
• /
• v.12 no.5
• /
• pp.641-648
• /
• 2009

Concrete structures become more common in railway systems with an advancement of high speed train technologies. As the service life of concrete structures increases, structural strengthening for concrete structures may be necessary. There are several typical strengthening techniques using steel plate and fiber reinforced polymer (FRP) materials, which have their own inherent shortcomings. In order to enhance greater durability and resistance to fire and other environmental attacks, basalt fiber material attracts engineer's attention due to its characteristics. This study investigates bonding performance of basalt fiber sheet as a structural strengthening material. Experimental variables include bond width, length and number of layer. From the bonding tests, there were three different types of bonding failure modes: debonding, rupture and rip-off. Among the variables, bond width indicated more significant effect on bonding characteristics. In addition the bond length did not contribute to bond strength in proportion to the bond length. Hence this study evaluated effective bond length and effective bond strength. The effective bond strength was compared to those suggested by other researches which used different types of FRP strengthening materials such as carbon FRP.

• Journal of the Korean Applied Science and Technology
• /
• v.33 no.1
• /
• pp.168-175
• /
• 2016

The surface of glass fiber bundle was modified with functionalized silanes and phenolic resin to improve the tensile strength as well as the adhesion of glass fiber to matrix phenolic resin. The surface modification of reinforcing glass fiber can play a significant role in controlling whole composite characteristics. We applied surface modification of glass fiber with two different functionalized silanes, such as glycidyltrimethoxysilane(G-silane) and aminopropyltriethoxysilane (A-silane), and phenol formaldehyde(PF) resin in one pot or separated process under different coating compositions and temperatures. Thermal treatment temperature is very important factor to improve the mechanical properties of modified glass fiber. Modified glass fiber bundle treated at $170^{\circ}C$ showed the highest tensile strength of $10.05g_f/D$. Surface analyses by scanning electron microscope(SEM) and FT-IR spectroscopy were used to characterize the surface coatings on glass fiber bundles. Mechanical property changes as functions of treatment conditions and coupling agent types were also explained.