• Journal of Sensor Science and Technology
• /
• v.7 no.3
• /
• pp.147-153
• /
• 1998

The strain characteristics of a fiber optic Fabry-Perot pressure sensor with high sensitivity using a $Si_{3}N_{4}/SiO_{2}/Si_{3}N_{4}$ (N/O/N) diaphragm is experimentally investigated. A 600 nm thick N/O/N diaphragm was fabricated by silicon anisotropic etching technology in 44 wt% KOH solution. An interferometric fiber optic pressure sensor has been manufactured by using a fiber optic Fabry-Perot intereferometer and a N/O/N diaphragm. The 2 cm length fiber optic Fabry-Perot interferometers in the continuous length of single mode fiber were produced with two pieces of single mode fiber coated with $TiO_{2}$ dielectric film utilizing the fusion splicing technique. The one end of the fiber optic Fabry-Perot interferometer was bonded to a N/O/N diaphragm. and the other end was connected to an optical setup through a 3 dB coupler. For the N/O/N diaphragm sized $2{\times}2\;mm^{2}$ and $8{\times}8\;mm^{2}$, the pressure sensitivity was measured 0.11 rad/kPa and 1.57 rad/kPa, respectively, and both of the nonlinearities were less than 0.2% FS.

• Journal of Sensor Science and Technology
• /
• v.5 no.1
• /
• pp.30-36
• /
• 1996

ZnO thin-film sensors were fabricated by RF magnetron sputtering method. The composition of the device material was 4 wt. % $Al_{2}O_{3}$, 1 wt. % $TiO_{2}$ and 0.2 wt. % $V_{2}O_{5}$ on the basis of ZnO material for developing the high sensitive TMA gas sensor which have an appropriate resistivity and the stability for practical use. They were also grown on the $SiO_{2}/Si$ substrates heated at $250^{\circ}C$ under a pure oxygen pressure of about 10 mTorr with a power of about 80 watts for 10 minutes. So as to enhance the stability of the resistivity, the thin films were annealed from $400^{\circ}C$ to $800^{\circ}C$. The sensors made with the thin film which were annealed at $700^{\circ}C$ for 60 minutes in pure oxygen gas exhibited a good sensing properties for TMA gas. The thin film grown at this condition showed the maximum sensitivity of 550 in TMA gas concentration of 160 ppm, and exhibited a good stability and excellent linearity.

• Journal of Radiation Protection and Research
• /
• v.35 no.1
• /
• pp.21-25
• /
• 2010

Burnup of spent fuel should be determined accurately for the safety control of spent fuel. Especially, it is necessary to measure the burnup profile along the nuclear fuel axis. In the present work, an ionization chamber was designed and fabricated to measure the gamma ray profile inside the guide tube of spent fuel. The ionization chamber was composed of three parts; induction part, gas-inlet part, and sensor part. The sensor part had two electrodes; cathode and anode. A guide electrode was considered in the ionization chamber design to make the ionization chamber to be inserted easily into the guide tube. Pure gas (argon and xenon) was inserted into the ionization chamber, and the leakage current and saturation curve were measured to determine the operation characteristics of the ionization chamber. The gamma ray radiation was also measured in relatively high dose environment. The gamma ray profile of the spent fuel will be measured with the ionization chamber.

• Journal of The Korean Association For Science Education
• /
• v.35 no.5
• /
• pp.907-917
• /
• 2015

Response to Intervention (RTI), which is focused on the gap between pre-interventions and post-interventions, provides an effective intervention program. This study takes under-achievement factors into consideration to determine the overall characteristics of underachievers. The under-achievement factors include cognitive learning factors, affective factors, and environmental factors. This study conducted curriculum-based assessments, achievement tests, and assessments on attitudes toward science and science learning motivation to verify the effects of individually tailored teaching according to the types of under-achievement in science. The experimental group was composed of six students in fourth grade, and the comparison group had 23 students. The findings of the study were as follows. First, the performance and progress of underachievers in the first-stage showed little progress and did not reach grade-level performance. Second, the underachievers in the second-stage greatly improved. In particular, the average of eight sessions in the second-step demonstrated performance beyond that of the regular child. Third, individually tailored teaching according to the types of under-achievement in science positively affected attitudes toward science and science learning motivation. This study will contribute to the improvement of the underachiever by applying individually tailored teaching according to the types of under-achievement in science.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.6
• /
• pp.490-497
• /
• 2020

Asphalt pavement accounts for more than 90% of the total pavement in Korea. Pavement is most widely constructed among construction structures. The heat transfer characteristics (Thermophysical Properties) of the asphalt pavement cause the heat island effect in downtown areas. An increasing asphalt surface temperature is one of the major causes of damage to asphalt pavement. This study examined the heat transfer characteristic factors according to solar energy accumulation in an asphalt mixture. The specimens (WC-2 & PA-13, Recycled aggregate used WC-2) used in the experiment were compacted with a Gyratory Compactor. The thermo-physical properties (thermal conductivity, specific heat capacity, thermal diffusivity, and thermal emissivity) and solar energy accumulation were evaluated. The thermal accumulation and HFM tests revealed a 1.2- to 2.0-fold difference. This indicates that the thermal conductivity of the asphalt mixture pavement changes with the accumulation of solar energy. An analysis of the correlation of thermal conductivity according to the surface temperature of the asphalt mixture showed that WC-2 was logarithmic, and PA-13 was linear. Experiments on the heat transfer characteristics of asphalt pavement that can be used for thermal failure modeling of asphalt were conducted.

• 한국지구물리탐사학회:학술대회논문집
• /
• 2008.10a
• /
• pp.51-56
• /
• 2008

The waveform inversion for isotropic media has ever been studied since the 1980s, but there has been few studies for anisotropic media. We present a seismic waveform inversion algorithm for 2-D heterogeneous transversely isotropic structures. A cell-based finite difference algorithm for anisotropic media in time domain is adopted. The steepest descent during the non-linear iterative inversion approach is obtained by backpropagating residual errors using a reverse time migration technique. For scaling the gradient of a misfit function, we use the pseudo Hessian matrix which is assumed to neglect the zero-lag auto-correlation terms of impulse responses in the approximate Hessian matrix of the Gauss-Newton method. We demonstrate the use of these waveform inversion algorithm by applying them to a two layer model and the anisotropic Marmousi model data. With numerical examples, we show that it's difficult to converge to the true model when we assumed that anisotropic media are isotropic. Therefore, it is expected that our waveform inversion algorithm for anisotropic media is adequate to interpret real seismic exploration data.

• Korean Journal of Optics and Photonics
• /
• v.18 no.1
• /
• pp.1-7
• /
• 2007

Filter colorimeters have a set of spectral bands for which spectral responsivity is the same as the color matching function defined by CIE (Commission Internationale de I'Eclairage). We have designed a set of color matching function filters denoted by $\bar{x}-filter,\;\bar{y}-filter,\;and\;\bar{z}-filter$. Because the $\bar{x}-function$ has two transmission bands, two $\bar{x}-filters$ are designed to cover the $\bar{x}-function$. To design the filters, we developed a nonlinear least square fit program which determines the thickness of the color glasses by minimizing its spectral mismatch value ($f{_1}'$) to below 3 %. The design has been validated by fabrication of the $\bar{y}-bar$ filter, of which $f{_1}'$ was measured to be 2.8 %. Considering a LCD flat panel display as a device under test, we have calculated the systematic error of the colorimetric measurement using the designed filters.

• Korean Journal of Weed Science
• /
• v.30 no.2
• /
• pp.103-110
• /
• 2010

This experiment was conducted to investigate seedling emergence and early growth of Monochoria vaginalis and Scirpus juncoides in the controlled-environment chamber maintained at different temperatures. Non-linear regression analyses of observed data against effective accumulated temperature (EAT) with the Gompertz and logistic models showed that the Gompertz and logistic models worked well in describing seedling emergence and early growth of both weed species, respectively, regardless of temperature. EATs required for 50% of the maximum seedling emergence and the maximum leaf number of M. vaginalis were estimated to be 69.3 and $131^{\circ}C$, respectively, while those of S. juncoides were 94.8 and $137^{\circ}C$, respectively. Models developed in this study thus were used to predict seedling emergence and early growth under elevated temperature condition. If rotary tillage with water is made on 27 May under $+3^{\circ}C$ elevated temperature condition, dates for 50% of the maximum seedling emergence and 4 leaf stage were predicted to be 1 June and 15 June for M. vaginalis and 3 June and 14 June for S. juncoides, respectively. As compared with current temperature, these dates are 1-2 days earlier for the seedling emergence and 3 days earlier for the early growth, suggesting that earlier application of herbicides is required for effective control of M. vaginalis and S. juncoides under elevated temperature condition in the future.

• Korean Journal of Weed Science
• /
• v.30 no.2
• /
• pp.94-102
• /
• 2010

Field and pot experiments were conducted to investigate seedling emergence and early growth of Eleocharis kuroguwai panted on different dates. Non-linear regression analyses of observed data against effective accumulated temperature (EAT) with the Gompertz model showed that the Gompertz model works well in describing seedling emergence and early growth of E. kuroguwai regardless of planting date and soil burial depth. EATs required for 50% of the maximum seedling emergence of E. kuroguwai planted at 1, 3 and 5 cm soil burial depth in the pot experiment were estimated to be 54.5, 84.0 and $118.0^{\circ}C$, respectively, and $56.7^{\circ}C$ when planted at 1 cm in the field experiment. EATs required for 50% of the maximum leaf number of E. kuroguwai planted at 1, 3 and 5 cm soil burial depth in the pot experiment were estimated to be 213.3, 249.0 and $291.6^{\circ}C$, respectively, and $239.5^{\circ}C$ when planted at 1 cm in the field experiment. Therefore, models developed in this study thus predicted that if rotary tillage with water is made on 27 May under $+2^{\circ}C$ elevated temperature condition, dates for 50% of the maximum seedling emergence, 5 leaf stage and 5 cm plant height of E. kuroguwai buried at 3 cm soil depth were predicted to be 2 June, 10 June and 12 June. These dates are 1 day earlier for the seedling emergence and 3 days earlier for the early growth as compared with current temperature condition, suggesting that earlier application of herbicides is required for effective control of E. kuroguwai.

• Information Systems Review
• /
• v.13 no.2
• /
• pp.1-16
• /
• 2011

Recently, many companies have started to manage and support CoPs formally at the organizational level because of strategic usability of CoP. These companies are also seeking ways to motivate CoP members to actively participate in their groups. Accordingly, this paper proposes one way of increasing CoP activities by rearranging CoP members. In practice, active CoP members often lead their groups. Therefore, rearranging members can, eventually, be one method to motivate more individuals to participate in CoP activities. This paper first suggests a new approach in order to improve knowledge sharing activities at the organizational level based on rearranging members of current CoPs. Second, a mathematical model is presented which maximizes total BLS (Balanced Level Score) of company A with several constraints. Then a real world problem is changed to a popular problem, VRP to solve this problem. Third, the solution program was developed to find a meaningful solution.