• Korean Chemical Engineering Research
• /
• v.50 no.4
• /
• pp.666-671
• /
• 2012

Gas hydrates are inclusion compounds formed when small-sized guest molecules are incorporated into the well defined cages made up of hydrogen bonded water molecules. Since large masses of natural gas hydrates exist in permafrost regions or beneath deep oceans, these naturally occurring gas hydrates in the earth containing mostly $CH_4$ are regarded as future energy resources. The heat of dissociation is one of the most important thermal properties in exploiting natural gas hydrates. The accurate and direct method to measure the dissociation enthalpies of gas hydrates is to use a calorimeter. In this study, the high pressure micro DSC (Differential Scanning Calorimeter) was used to measure the dissociation enthalpies of methane, ethane, and propane hydrates. The accuracy and repeatability of the data obtained from the DSC was confirmed by measuring the dissociation enthalpy of ice. The dissociation enthalpies of methane, ethane, and propane hydrates were found to be 54.2, 73.8, and 127.7 kJ/mol-gas, respectively. For each gas hydrate, at given pressures the dissociation temperatures which were obtained in the process of enthalpy measurement were compared with three-phase (hydrate (H) - liquid water (Lw) - vapor (V)) equilibrium data in the literature and found to be in good agreement with literature values.

• Journal of Animal Environmental Science
• /
• v.6 no.3
• /
• pp.175-184
• /
• 2000

A lab-scale MF membrane reactor was installed to investigate the membrane permeability, characteristics of membrane fouling at each conditions, and quality of permeate (liquid livestock manure) in the separation of solid-matters using membrane. Experiment was divided three filtration type such as follows; continuous filtration, gravity filtration, and intermittent filtration. As a result of experiment, flux 1 LMH was maintained for 7days, and trans-membrane pressure(TMP) was increased gradually under 10cmHg, but it was increased immediately after 10cmHg, respectively. However, the flux was increased, the Tmax was decreased exponential more and more. During the pure-flux test, most of the fouling of membrane was reversible. At the gravity filtration, permeate could be obtained as 1.75 LMH for 3.5days without any other electronic pressure. As an investigation of membrane surface, this study could be decided that the reason of fouling at the lower flux (Run 1 and 2) was attached matters in membrane surface, but at the higher flux (Run 4-6) was concentration polarization.

• Economic and Environmental Geology
• /
• v.45 no.2
• /
• pp.71-78
• /
• 2012

Illite-smectite mixed layers (I-S) occurring authigenically in diagenetic and hydrothermal environments reacts toward more illite-rich phases as temperature and potassium ion concentration increase. For that reason, I-S is often used as geothermometry and/or geochronometry at the field of hydrocarbons or ore minerals exploration. Generally, I-S shows X-ray powder diffraction (XRD) patterns of ultra-thin lamellar structures, which consist of restricted numbers of sillicate layers (normally, 5 ~ 15 layers) stacked in parallel to a-b planes. This ultra-thinness is known to decrease I-S expandability (%S) rather than theoretically expected one (short-stacking effect). We attempt here to quantify the short stacking effect of I-S using the difference of two types of expandability: one type is a maximum expandability ($%S_{Max}$) of infinite stacks of fundamental particles (physically inseparable smallest units), and the other type is an expandability of finite particle stacks normally measured using X-ray powder diffraction (XRD) ($%S_{XRD}$). Eleven I-S samples from the Geumseongsan volcanic complex, Uiseong, Gyeongbuk, have been analyzed for measuring $%S_{XRD}$ and average coherent scattering thickness (CST) after size separation under 1 ${\mu}m$. Average fundamental particle thickness ($N_f$) and $%S_{Max}$ have been determined from $%S_{XRD}$ and CST using inter-parameter relationships of I-S layer structures. The discrepancy between $%S_{Max}$ and $%S_{XRD}$ (${\Delta}%S$) suggests that the maximum short-stacking effect happens approximately at 20 $%S_{XRD}$, of which point represents I-S layer structures consisting of ca. average 3-layered fundamental particles ($N_f{\approx}3$). As a result of inferring the $%S_{XRD}$ range of each Reichweite using the $%S_{XRD}$ vs. $N_f$ diagram of Kang et al. (2002), we can confirms that the fundamental particle thickness is a determinant factor for I-S Reichweite, and also that the short-stacking effect shifts the $%S_{XRD}$ range of each Reichweite toward smaller $%S_{XRD}$ values than those that can be theoretically prospected using junction probability.

• The Korean Journal of Food And Nutrition
• /
• v.25 no.4
• /
• pp.807-819
• /
• 2012

To evaluate the functional characteristic and availability for drinking of the fermented Smilax china leaf tea by using different microbial species, various fermented leaf tea was prepared by non-fermentation (C), or the fermentation of Saccharomyces cerevisiae (S), Bacillus sp. (B), Bifidobacterium bifidus (L), Monascus pilosus (M) and Aspergilus oryzae (A), and sensory and antioxidant parameter of each brewed tea was observed. The color of the A tea was red, but the other teas were yellow in color. Furthermore, the aesthetic quality of the A and M tea was 3.95 and 3.30 point, respectively, and other teas (2.55~2.28) were similar to that of the C tea. TP of fermented tea water extract was lower than that of the C, although TF was not significantly different between the fermented and non-fermented tea. Especially, TF of the A tea was significantly lower than those of the other teas. The range of EDA ($1mg/m{\ell}$) of water and ethanol extracts of tea C and the fermented teas was 19.25~22.48%; however, tea A was only 8.04~12.49%. In addition, FRAP, FICA and LPOIA of teas were not significantly different between the fermented and non-fermented teas. On the other hand, XOIA and AOIA of tea ethanol extracts were slightly higher than those of water extracts. XOIA of water extract derived from the teas was 4.83~9.20%, while ethanol extract of these was 9.00~19.00%. However, XOIA of B and L teas water extract was not detected. Furthermore, AOIA of fermented tea water extract (30.17~48.52%) were lower than those of ethanol extract (44.09~66.93%). In this study, interestingly, antioxidant parameters, such as FRAP, FICA, LPOIA and AOIA, of the A tea water extract (0.1%) was higher than that of the other tea in spite of high decreasing rate in the contents of TP and TF. Therefore, above results imply the possibility of fermented Smilax china leaf tea as a functional food.

• Korean Journal of Remote Sensing
• /
• v.33 no.5_1
• /
• pp.571-585
• /
• 2017

The number of spaceborne optical sensors including red-edge band has been increasing since red-edge band is known to be effective to enhance the information content on biophysical characteristics of vegetation. Considering that the Agriculture and Forestry Satellite is planning to carry an imaging sensor having red-edge band, we tried to analyze the current status and potential of red-edge band. As a case study, we analyzed the effect of using red-edge band and tried to find the optimum band width and wavelength region of the red-edge band to estimate leaf area index (LAI) of very dense tree canopy. Field spectral measurements were conducted from April to October over two tree species (white oak and pitch pine) having high LAI. Using the spectral measurement data, total 355 red-edge bands reflectance were simulated by varying five band width (10 nm, 20 nm, 30 nm, 40 nm, 50 nm) and 71 central wavelength. Two red-edge based spectral indices(NDRE, CIRE) were derived using the simulated red-edge band and compared with the LAI of two tree species. Both NDRE and CIRE showed higher correlation coefficients with the LAI than NDVI. This would be an alternative to overcome the limitation of the NDVI saturation problem that NDVI has not been effective to estimate LAI over very dense canopy situation. There was no significant difference among five band widths of red-edge band in relation to LAI. The highest correlation coefficients were obtained at the red-edge band of center wavelength near the 720 nm for the white oak and 710 nm for the pitch pine. To select the optimum band width and wavelength region of the red-edge band, further studies are necessary to examine the relationship with other biophysical variables, such as chlorophyll, nitrogen, water content, and biomass.

• Korean Journal of Materials Research
• /
• v.11 no.7
• /
• pp.556-561
• /
• 2001

We prepared a new a SOS(silicon-on-silicide) wafer pair which is consisted of Si(100)/1000$\AA$-NiSi Si (100) layers. SOS can be employed in MEMS(micro- electronic-mechanical system) application due to low resistance of the NiSi layer. A thermally evaporated $1000\AA$-thick Ni/Si wafer and a clean Si wafer were pre-mated in the class 100 clean room, then annealed at $300~900^{\circ}C$ for 15hrs to induce silicidation reaction. SOS wafer pairs were investigated by a IR camera to measure bonded area and probed by a SEM(scanning electron microscope) and TEM(transmission electron microscope) to observe cross-sectional view of Si/NiSi. IR camera observation showed that the annealed SOS wafer pairs have over 52% bonded area in all temperature region except silicidation phase transition temperature. By probing cross-sectional view with SEM of magnification of 30,000, we found that $1000\AA$-thick uniform NiSi layer was formed at the center area of bonded wafers without void defects. However we observed debonded area at the edge area of wafers. Through TEM observation, we found that $10-20\AA$ thick amourphous layer formed between Si surface and NiSix near the counter part of SOS. This layer may be an oxide layer and lead to degradation of bonding. At the edge area of wafers, that amorphous layer was formed even to thickness of $1500\AA$ during annealing. Therefore, to increase bonding area of Si NiSi ∥ Si wafer pairs, we may lessen the amorphous layers.

• Korean journal of communication and information
• /
• v.35
• /
• pp.250-291
• /
• 2006

This study examines the regulatory issues and introduction problems of TV-betting data broadcasts in Korea by in-depth interview with a panel group. TV-betting data broadcast services of card games and horse racing games are widely in use in Europe and other parts of the world. In order to carry out the study, a demo program of TV-betting data broadcast in the OCAP(OpenCableTM Application Platform Specification) system environment, which is the data broadcasting standard for digital cable broadcasts in Korea was exposed to the panel group and then they were interviewed after watching and using the program. The results could be summarized as below. First of all, while TV-betting data broadcasts have many elements of entertainment, the respondents thought that it would be difficult to introduce TV-betting in data broadcasts as in overseas countries largely due to social factors. In addition, in order to introduce TV-betting data broadcasts, they suggested that excessive speculativeness must be suppressed through a series of regulatory system devices, such as by guaranteeing credibility of the media based on safe security systems for transactions, scheduling programs with effective time constraints to prevent the games from running too frequently, limiting the betting values, and by prohibiting access to games through set-top boxes of other data broadcast subscribers. The general consensus was that TV-betting could be considered for gradual introduction within the governmental laws and regulations that would minimize its ill effects. Therefore, the government should formulate long-term regulations and policies for data broadcasts. Once the groundwork is laid for safe introduction of TV-betting on data broadcasts within the boundary of laws and regulations, interactive TV games are expected to be introduced in Korea not only for added functionality of entertainment but also for far-ranging development of data broadcast and new media industries.

• Journal of Plant Biotechnology
• /
• v.45 no.2
• /
• pp.117-124
• /
• 2018

The imports of Centella asiatica L. Urban are increasing year-by-year due to the fact that its extract is a raw material used for skin wounds and in cosmetics. However, studies on the cultivation and identification of native C. asiatica species in Korea have been extremely rare. Therefore, this study was conducted in order to investigate the physiological and functional activity of Korean native C. asiatica plant cultivated in Hapcheon, Gyeongsangnam-do, Korea. As a result, the highest antibacterial and anti-inflammatory activities were examined with methanol extract while skin-whitening and wrinkle improvement were examined with water extract. Seven bacterium and one fungus were treated with 50% methanol extracts of C. asiatica and most of the bacterium showed similar or low levels of antibacterial activity compared to the control group of Omiza (Schisandra chinensis) extract, except for Streptococcus pyogenes, which showed higher antimicrobial activity than that of Omiza extract. However, neither C. asiatica and Omiza extracts showed antimicrobial activity against the fungus, C. albicans. The results of anti-inflammatory effect analyses with Raw 264.7 cells confirmed that the treatment of methanol extract reduced the level of NO by 50% or more compared to the control group. In addition, the water extract showed the highest reduction of melanin content of up to 20% more than the control group when examined with B16F10 cell line, indicating a significant skin-whitening effect. Furthermore, we were able to show the significant skin wrinkle improvement caused by C. asiatica extract with NHDF cell as an indicator, but strong cytotoxicity was also observed, suggesting that further studies are necessary.

• Korean Journal of Food Science and Technology
• /
• v.32 no.4
• /
• pp.755-762
• /
• 2000

Physicochemical properties of commercial sweet potato starches manufactured by 7 different companies were investigated in comparison with corn and potato starches. Crude ash and protein content varied from 0.36 to 1.02%, and from 0.04 to 0.14% based on dry weight, respectively. The protein contents were relatively smaller than that of corn or potato starch. But whiteness of the sweet potato starches was less than that of corn or potato starch. Mean diameter of the sweet potato starch granules varied from 14.23 to $21.08\;{\mu}m$ depending on the company and all sweet potato starches showed bimodal size distributions. Pasting viscosity measured by Rapid Viscoanalyzer(RVA) also showed variations among the starches of different companies. The starch from D company in Korea had the lowest pasting temperature$(74.00^{\circ}C)$ whereas the starch from a phillippine company(P) did the highest one$(80.35^{\circ}C)$. The peak viscosity of sweet potato starches was higher than that of corn starch but lower than that of potato starch. The D company starch also showed the highest peak viscosity(2283 cp) among the starches tested. Paste breakdown by hot shearing ranged from 524 cp (S company) to 1279 cp (HL company). Textural properties of the starch gels appeared significantly different among the starches of different manufacturers. The greatest hardness of the gel was $137.90\;g_{f}$ at 1 day storage whereas the lowest value was $31.53\;g_{f}$. Except the starches from 2 companies (P and S), the sweet potato starches formed very soft and weak gels. P or S company starches formed the gels similar to potato starch. Syneresis by freeze-thawing treatments appeared less for sweet potato starch gels than that for corn starch gels, but greater than that for potato starch gel. The overall properties of the sweet potato starches varied by the manufacturing companies, and ranged between those of corn and potato starches.

• Proceedings of the Korean DIstribution Association Conference
• /
• 2006.08a
• /
• pp.47-68
• /
• 2006

This study aims to determine the association structure of the behavioral relationship variables, such as trust, commitment, cooperation, communication and coercive power, in the relationship between the buyers and suppliers of industrial parts. It also investigates the impact of the use of IT technologies on the relationships quality. Data was collected from 216 part suppliers of machinery, electronics and automobiles located in Incheon. Data supported all of the proposed hypotheses. First, it was confirmed that parts suppliers' trust in buyers leads to the commitment into relationships with buyers. Second, cooperation and communication showed a positive influence on parts suppliers' trust in buyers, and coercive power gave a negative influence on trust. Third, the use of IT technologies like Internet and E-Mail between parts suppliers and buyers was verified to have generally a positive influence on the quality of relationships. At the same time, cooperation and communication were confirmed to have a positive influence on each other, and cooperation and coercive power as well as communication and coercive power were confirmed to have negative influence on each other. This study is a pioneering attempt to examine the relationships between suppliers and buyers of industrial parts, and the influence IT technologies on the relationship quality. Also, the findings will be practically much helpful to find how to reinforce the relationships between parts suppliers and buyers.