• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.35 no.1A
• /
• pp.80-86
• /
• 2010

This work has been measured and analyzed the device degradation of NBTI (Negative Bias Temperature Instability) stress induced the increase of gate-induced-drain-leakage(GIDL) current for p-MOS transistors of gate channel length 0.13 [${\mu}m$]. From the relation between the variation of threshold voltage and subthreshold slop by NBTI stress, it has been found that the dominant mechanism for device degradation is the interface state generation. From the GIDL measurement results, we confined that the EHP generation in interface state due to NBTI stress led to the increase of GIDL current. As a results, one should take care of the increased GIDL current after NBTI stress in the ultra-thin gate oxide device. Also, the simultaneous consideration of reliability characteristics and dc device performance is highly necessary in the stress parameters of nanoscale CMOS communication circuit design.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.23 no.4
• /
• pp.61-68
• /
• 2019

As the pollution of water resources deteriorates due to industrialization and urbanization, it is difficult to supply clean water through a water treatment method using chlorine. Therefore, the introduction of advanced water treatment facilities using ozone is on the increase. However, epoxy which is used as waterproofing and anticorrosives and stainless steel used in conventional waterproofing and anti-corrosive methods have deteriorated because of the strong oxidizing power of ozone, causing problems such as leaking. Moreover, it even causes the durability degradation of a concrete. Therefore, in this study, metal spraying system was used as the means of constructing a metal panel with excellent ozone resistance and chemical resistance which is an easier method than an existing construction method. Ozone resistance was evaluated in accordance with the type of metal sprayed coatings to develop a finishing method which can prevent the concrete structure of water treatment facilities from deterioration. Furthermore, electrochemical stability in actual sewage treatment plant environment was evaluated. Experimental results showed that Ti has superior ozone resistance after spraying and the electrochemical stability in the sewage treatment plant environment showed that Ti has the highest polarization resistance of $403.83k{\cdot}{\Omega}{\cdot}cm^2$, which ensures high levels of durability.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.202-202
• /
• 2012

유연성 투명 전도막은 현대 전자산업의 발전에 있어 필수적인 부품소재로서, 가시광선의 투과율이 80% 이상이고 면저항이 $100{\Omega}/sq.$ 전후이며 휘거나 접히고 나아가 두루마리의 형태로도 응용이 가능한 소재를 일컫는다. 이러한 유연성 투명 전도막은 차세대 정보디스플레이 산업 및 유비쿼터스 사회의 중심이 되는 유연성 디스플레이, 터치패널, 발광다이오드, 태양전지 등 매우 다양한 분야에 응용이 기대된다. 이러한 이유로 고 신뢰성 유연성 투명 전도막 개발기술은 차세대 산업에 있어서의 핵심기술로 인식되고 있다. 현재로서는 인듐 주석 산화물(indium tin oxide; ITO) 및 전도성 유기고분자를 사용하여 투명 전도막을 제조하고 있으나, ITO 박막의 경우 인듐 자원의 고갈로 인한 가격상승 및 기판과의 낮은 접착력, 열팽창계수의 차이로 인한 공정상의 문제, 산화물 특유의 취성으로 인한 유연소자로서의 내구성 저하 등의 문제가 제기되고 있다. 전도성 유기고분자의 경우는 낮은 전기전도도와 기계적강도, 유기용매 처리 등의 문제점이 지적되고 있다. 따라서 높은 전기전도도와 투광도 뿐만 아니라 유연성을 지니는 재료의 개발이 요구되고 있는 실정이다. 최근 이러한 재료로서 그래핀(graphene)과 탄소나노튜브(carbon nanotube; CNT)를 중심으로 하는 탄소나노재료가 주목받고 있으며 많은 연구가 활발히 진행되고 있다. 본 연구에서는 열화학기상증착법(thermal vapor deposition; TCVD)으로 합성된 그래핀 및 CNT를 이용하여 탄소나노재료 복합체 기반의 유연성 투명 전도막을 제작하고 그 특성을 평가하였다. 그래핀과 CNT합성을 위한 기판으로는 각각 300 nm 두께의 니켈과 1 nm 철이 증착된 실리콘 웨이퍼를 이용하였으며, 원료가스로는 메탄(CH4)과 아세틸렌(C2H2)등의 탄화수소가스를 이용하였다. 그래핀의 경우 원료가스의 유량, 합성온도, 냉각속도를 변경하여 대면적으로 두께균일도가 높은 그래핀을 합성하였으며, CNT의 경우 합성시간을 변수로 길이 제어합성을 도모하였다. 합성된 그래핀은 식각공정을, CNT는 스프레이 증착공정을 통해 고분자 기판(polyethylene terephthalate; PET) 위에 순차적으로 전사 및 증착하여 탄소나노재료 복합체 기반의 유연성 투명 전도막을 제작하였다. 제작된 탄소나노재료 복합체 기반의 유연성 투명 전도막은 물리적 과부하를 받았을 때 발생할 수 있는 유연성 투명 전도막의 구조적결함에 기인하는 전도성 저하를 보상하는 특징이 있어, 그래핀과 탄소나노튜브 각각으로 제조된 유연성 투명 전도막보다 물리적인 하중이 반복적으로 인가되었을 때 내구성이 향상되는 효과가 있다. 40% 스트레인을 반복적으로 인가하였을 때 그래핀 투명 전도막은 20 사이클 이후에 면저항이 $1-2{\Omega}/sq.$에서 $15{\Omega}/sq.$ 이상으로 급증한 반면 그래핀-CNT 복합체 투명 전도막은 30사이클까지 $1-2{\Omega}/sq.$ 정도의 면저항을 유지하였다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.8
• /
• pp.248-255
• /
• 2020

The effects of the coating thickness on the thermal durability and thermal stability of thermal barrier coatings (TBCs) with a gradient coating thickness were investigated using a flame thermal fatigue (FTF) test and thermal shock (TS) test. The bond and topcoats were deposited on the Ni-based super-alloy (GTD-111) using an air plasma spray (APS) method with Ni-Cr based MCrAlY feedstock powder and yttria-stabilized zirconia (YSZ), respectively. After the FTF test at 1100 ℃ for 1429 cycles, the bond coat was oxidized partially and the thermally grown oxide (TGO) layer was observed at the interface between the topcoat and bond coat. On the other hand, the interface microstructure of each part in the TBC specimen showed a good condition without cracking or delamination. As a result of the TS test at 1100 ℃, the TBC with gradient coating thickness was initially delaminated at a thin part of the coating layer after 37 cycles, and the TBC was delaminated by more than 50% after 98 cycles. The TBCs of the thin part showed more oxidation of the bond coat with the delamination of topcoat than the thick part. The thick part of the TBC thickness showed good thermal stability and oxidation resistance of the bond coat due to the increased thermal barrier effect.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.16 no.4
• /
• pp.300-305
• /
• 1987

Changes in pigments of freeze dried grasshopper in refrigerator were determined to asses the storage stability. In storage at $5^{\circ}C$, chlorophyll contents were drastically decreased but pheopytins were increased. The degradation of chlorophylls get under controlled with vacuum package. The pigments extracted from 98 days stored samples were fractionated by silicic acid column and obtained 3 portions (3a, 3b and 3d). These portions were compared Rf values (0.75, 0.56, 0.50, respectively) and absorption spectra (408, 666nm; 419, 651nm; 433, 655nm, respectively) with that of standard and were identifed pheophytin a and b and 'changed' chlorophyll a. Especially, pheophytins a and b were great strength accelerated to lipid oxidation.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.4
• /
• pp.135-143
• /
• 2013

In this study, we suggested effective countermeasure of biodiesel oxidation problems by investigating the oxidation degradation of biodiesels derived from variable resources and the level of oxidation stability of current distributing biodiesel blended fuels (2%) in Korea, and oxidation stability change according to storage time (for 3 month) and biodiesel blending ratio (2, 5, 7, 10%). By the composition analysis results of biodiesel from various resources which are possible to distribute in Korea, the biodiesel from animal fat has poor oxidation stability and cold performance, while the biodiesel from coconut and palm kernel which are considered as future potential raw material showed good oxidation stability and cold performance. The oxidation stability level of current distributing biodiesel blended fuels in Korea was excellent with showing over 30 hours (average 68 hours) stability, but the oxidation stability of the blended fuel with animal fat biodiesel having poor oxidation property (1.22 hours) was rapidly decreased to below 32 hours by mixing only 2%. Therefore, we have to pay attention to quality control of oxidation property, because the oxidation stability problem can be caused by increasing biodiesel blending ratio and diversifying raw materials those have worse property.

• Journal of the Korean Magnetics Society
• /
• v.15 no.1
• /
• pp.42-47
• /
• 2005

Nanocrystalline Nd-Fe-B powder was synthesized by a new thermochemical process that combined with past reduction-diffusion process and spray-dry process. In this process, Ca reduction process is vary important due to formation of hard magnetic$Nd_{2}Fe_{14}B$ phase from various oxides by Ca powder. Therefore, the final products are essentially affected a shape, size, and composition etc. of the Ca reduced powders. Ca reduction was performed to way that raw powders just mixed with Ca powder in proper ratio unlike to compress into compact. The powders after mixture-type Ca reduction mainly composited with $Nd_{2}Fe_{14}B$ phase even relativily low reaction temperature ($800^{\circ}C$) and all particle size of powder were distributed less than 1 ${\mu}m$ except for powder after Ca oxides as magnetic properties of powders after cake-type Ca reduction, with the consequence that high magnetic properties has been expected. The magnetic properties of powders prepared by mixture-type Ca ruduction, with the conseqence that high magnatic properties has been expected. The magnetic properties of powders prepared by mixture-type Ca reduction process showed $_iH_c$ = 5.9 kOe, $B_r$ = 5.5 kG, (BH)max = $Nd_{2}Fe_{14}B{\to}Nd_{2}Fe_{17}B$ decomposition by violent exothermic reaction during washing.

• Journal of the Korean Society of Safety
• /
• v.34 no.4
• /
• pp.1-5
• /
• 2019

In the field of combined cycle power generation, thermal barrier coating(TBC) protects the super-heat-resistant alloy, which forms the core component of the gas turbine, from high temperature exposure. As the turbine inlet temperature(TIT) increases, TBC is more important and durability performance is also important when considering maintenance cost and safety. Therefore, studies have been made on the fabrication method of TBC and super-heat-resistant alloy in order to improve the performance of the TBC. In recent years, due to excellent properties such as high temperature creep resistance and high temperature strength, turbine blade material have been replaced by a single crystal superalloy, however there is a lack of research on TBC applied to single crystal superalloy. In this study, to understand the isothermal degradation performance of the TBC applied to the single crystal superalloy, isothermal exposure test was conducted at various temperature to derive the delamination life. The growth curve of thermally grown oxide(TGO) layer was predicted to evaluate the isothermal degradation performance. Also, microstructural analysis was performed by scanning electron microscope(SEM) and energy dispersive X-ray spectroscopy (EDS) to determine the effect of mixed oxide formation on the delamination life.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.36D no.10
• /
• pp.17-22
• /
• 1999

In this paper, the results of the studies about a new proposal where the ONON(oxide-nitride-oxide-nitride) layer instead of the conventional ONO(oxide-nitride-oxide) layer is used as the IPD(inter-poly-dielectrics) layer to improve the data retention problem in the Flash EEPROM cell, have been discussed. For these studies, the stacked-gate Flash EEPROM cell with an about 10nm thick gate oxide and on ONO or ONON IPD layer have been fabricated. The measurement results have shown that the data retention characteristics of the devices with the ONO IPD layer are significantly degraded with an activation energy of 0.78 eV. which is much lower than the minimum value (1.0 eV) required for the Flash EEPROM cell. This is believed to be due to the partial or whole etching of the top oxide of the IPD layer during the cleaning process performed just prior to the dry oxidation process to grow the gate oxide of the peripheral MOSFET devices. Whereas the data retention characteristics of the devices with the ONON IPD layer have been found to be much (more than 50%) improved with an activation energy of 1.10 eV. This must be because the thin nitride layer on the top oxide layer in the ONON IPD layer protected the top oxide layer from being etched during the cleaning process.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.135-135
• /
• 2016

차세대 가스터빈 엔진 및 초음속 항공기 내 고온부의 온도가 증가함에 따라, 기존의 초내열합금 기반 소재를 사용하기 어려워지고 있다. 초고온 세라믹스는 높은 기계적 물성, 화학적 안정성 등 우수한 고온 특성을 가지고 있어 기존의 초고온 소재를 대체 할 수 있는 물질로 부상되고 있다. 하지만 기존의 금속 기반 소재 대비 높은 밀도로 인하여 초고온 세라믹 단일체를 비행체 부품에 적용하기에는 어려움이 있다. 이에 초고온 세라믹스와 탄소섬유를 포함하는 세라믹 복합체(Ceramic Matrix Composite, CMC)를 제작하여 동등한 기계적 물성을 보이면서 무게를 감소시키는 연구들이 진행 중에 있다. 초고온 세라믹스가 함침 된 세라믹 복합체의 경우 우수한 내삭마, 내산화 특성을 보이지만, 장시간 고온에 노출되어 탄소 섬유가 드러나게 되면 급격한 산화로 인해 소재 특성의 열화가 진행되는 단점을 가지고 있다. 따라서, 탄소 섬유가 드러나지 않도록 복합체 표면에 코팅층을 형성하여 세라믹 복합체 모재를 보호하는 방법이 활발히 연구되고 있다. 본 연구에서는 진공 플라즈마 용사 공정을 이용하여 다양한 공정조건 하에서 초고온 세라믹 코팅층을 형성하였다. 수십 마이크론 크기 분포를 갖는 HfC 분말을 Ar 유송 가스를 이용하여 플라즈마 화염 내부로 투입하였다. 플라즈마 화염 가스는 Ar 과 H2를 혼합하여 구성되었으며, 분위기 가스로는 N2를 사용하였다. 코팅에 사용된 모재로는 ZrB2 단일체와 SiC가 미량 포함된 HfC 단일체를 사용하였다. 다양한 공정 조건하에서 형성된 HfC 코팅층의 두께, 미세 조직구조를 SEM을 이용하여 관찰하였으며, XRD를 이용하여 형성된 HfC 코팅층의 결정구조를 분석하였다.