• Korean Journal of Optics and Photonics
• /
• v.12 no.3
• /
• pp.219-224
• /
• 2001

Spectral phase interferometry for direct electric-field reconstruction (SPIDER) was fabricated and used to characterize pulses from a Ti:sapphire oscillator. In the SPIDER apparatus, two replicas of the input pulse were generated with a time delay of 200 fs and were upconverted by use of sum-frequency generation with a strongly chirped pulse using a 8-cm-long SFIO glass block at a 30-11m-thick type II BBO (p-BaBz04) crystal. The resulting interferogram was recorded with a UV-enhanced CCD array in the spectrometer. The spectral phase was retrieved by SPIDER algorithm in combination with independently measured pulse spectrum and the corresponding temporal intensity profile was reconstructed with a duration of 19 fs. As an independent cross-check of the accuracy of the method, we compared the interferometric autocorrelation (lAC) signal calculated from the SPIDER data with a separately measured lAC. The conventional, but unjustified, method of fitting a sechz pulse to the autocorrelation deceivingly yielded a pulse duration of 15 fs. This systematic underestimation of the pulse duration affirms the need for a complete characterization method. From the consideration in this paper, we concluded that the SPIDER could provide an accurate characterization of femtosecond pulses. ulses.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.37 no.3
• /
• pp.14-19
• /
• 2000

Free-standing GaN single crystal substrates have been obtained by growing thick GaN epitaxial layers on (0001) sapphire substrates using hydride vapor phase epitaxy (HVPE) method. After growing the GaN thick film of 200 ${\mu}{\textrm}{m}$, a free-standing GaN with a size of 10 mm $\times$10 mm were obtained by mechanical polishing process to remove sapphire substrate. Crack-free GaN substrates have been obtained by GaCl pre-treatment prior to the growth of GaN epitaxial layers. Properties of free-standing GaN substrates have been compared with those of lateral epitaxial overgrowth (LEO) GaN films by double-crystal x-ray diffraction (DC-XRD), cathodoluminescence (CL) and photoluminescence (PL) measurements.

• Journal of Sensor Science and Technology
• /
• v.6 no.2
• /
• pp.155-162
• /
• 1997

Zinc oxide(ZnO) thin films were deposited on r-plane sapphires from a solution containing zinc acetate. The films were obtained in a hot wall reactor by the pyrolysis of an aerosol produced by an ultrasonic generator. The crystallinity, surface morphology and composition of the films have been studied using the x-ray diffraction method(XRD) scanning electron microscopy(SEM) and Auger electron spectroscopy (AES) respectively. The influences of the substrate temperature on the crystallinity of the films were studied. Strongly (110) oriented ZnO films were obtained at a substrate temperature of $350^{\circ}C$. The resistivity was increased to above $3{\times}10^{6}{\Omega}{\cdot}cm$ with copper doping and vapor oxidation.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.17 no.5
• /
• pp.672-679
• /
• 2014

To improve sensing capability of infrared, heat-resistance and mechanical properties, the $SiO_2$ and $TiO_2$ anti-reflective layers were coated on sapphire substrate by MOCVD. The standard wavelength was 4,600nm, and the thickness of anti-reflective layers were 379 and 758nm in case of ${\lambda}/4$ and ${\lambda}/2$ of incident angle($65^{\circ}$), respectively. The $SiO_2$ and $TiO_2$ anti-reflective layers were coated 12.6 and 9.7nm/min of deposition rates by increasing oxygen pressure to set the ideal refractive index of 1.283. In case of $SiO_2({\lambda}/2)$ coating, the transmittance increased from 55.0 to 62.7%. The transmittance of $TiO_2({\lambda}/2)$ anti-reflective layer also increased from 55.0 to 64.8%. The flexural strength of $SiO_2({\lambda}/2)$ and $TiO_2({\lambda}/2)$ layer coated sapphire increased from 337.8 to 362.9 and 371.8MPa, respectively. The flexural strength at $500^{\circ}C$ of these materials also increased respectively to 304.5, 358.2MPa from 265.9MPa. From these results, we confirmed these materials can be used as transmission window of infrared light.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.230-230
• /
• 2010

질화갈륨 기반의 III족-질화물 계열의 반도체 물질은 녹색-자외선 영역의 발광다이오드에 응용되어 왔으며 고효율, 고휘도 발광소자의 구현 및 성능 향상을 위해 많은 연구가 진행되었다. 일반적으로 널리 사용되어온 c축 방향으로 성장된 질화갈륨 기반 발광다이오드에서는 활성층의 에너지 밴드구조가 내부전기장에 의해 변형되어 전자와 정공의 재결합 확률이 저하된다. c축 방향으로 형성되는 내부전기장은 축방향으로의 자발적 분극화와 높은 압전 분극 현상에 기인한다. 이와 같은 분극 성장에서의 내부양자효율 저하 현상을 해결하기 위하여 내부 전기장이 존재하지 않는 a축과 m축과 같은 무분극 방향으로의 성장이 집중적으로 연구되고 있다. 현재 사파이어 기판위에서 무분극 성장된 박막은 높은 밀도의 결함이 발생하여 고품위의 발광다이오드 동작에 어려움을 겪고 있다. 최근 결함 밀도를 낮추고 높은 결정성을 갖는 무분극 질화갈륨 박막을 성장하기 위하여 2-단계 성장 방법, 나노구조층 삽입, 산화규소 마스크 패턴 등 다양한 성장 방법들이 연구되어 주목할 만한 연구 결과들이 보고되고 있다. 다양한 성장 방법들에 의해 성장된 박막들은 고유한 특성들을 보이는데, 특히 박막 성장방법에 따라 박막 내부에 형성되는 깊은 준위의 특성들은 발광다이오드의 소자 특성에도 큰 영향을 미치게 되므로 무분극 박막에서의 깊은 준위에 대한 연구가 필요하다. 본 연구에서는 금속-유기 화학기상증착 방법으로 r면의 사파이어기판 위에 a면의 질화갈륨을 성장시켰다. 고품질의 결정성을 구현하기 위해 저온 핵형성층, 3차원 성장층, 2차원 중간온도 성장층, 2차원 성장층의 4개 버퍼층을 사용하였으며, 질화규소 나노구조층을 삽입함으로써 고품 위의 a면 질화갈륨 박막을 구현하였다. 성장된 a면 질화갈륨 박막에 형성된 깊은 준위들은 접합용량과도분광법을 이용하여 분석되었으며 질화규소 삽입층의 유무에 따른 깊은 준위의 특성 차이에 대한 연구를 수행하였다.

• Journal of the Korean Vacuum Society
• /
• v.19 no.1
• /
• pp.58-65
• /
• 2010

AlN thin films were deposited on sapphire substrates and ZnO templates by rf-magnetron sputtering. Powder-sintered AlN target was adopted for source material. Thickness of AlN layer was linearly dependent on plasma power from 50 to 110 W, and it decreased slightly when working pressure increased from 3 to 10 mTorr due to short mean free path of source material sputtered from AlN target by Ar working gas. When $N_2$ gas was mixed with Ar, the thickness of AlN layer decreased significantly because of low sputter yield of nitrogen. AlN layer was also deposited on ZnO template. However, it showed weak thermal stability that the interface between AlN and ZnO was deteriorated by rapid thermal annealing treatment above $700^{\circ}C$. In addition, ZnO layer was largely attacked by MOCVD ambient gas of hydrogen and ammonia around $700^{\circ}C$ through inferior AlN layer deposited by sputtering. And AlN layers were fully peeled off above $900^{\circ}C$.

• Korean Journal of Materials Research
• /
• v.11 no.4
• /
• pp.319-323
• /
• 2001

In order to investigate the effect of thickness on the properties of ZnO thin films, a series of films having different thickness were deposited on (0001) sapphire by using pulsed laser deposition(PLD). SEM and XRD analyses showed that, as the film thickness increases, the grain size increased and the crystallinity improved. Room-temperature PL spectra also exhibited that the intensities of both ultraviolet and deep level emission Peaks increased as the film thickness increased. Hall measurements at room- temperature revealed that, as the film thickness changes from 400 to 4000 , the carrier concentration of the film showed sharp decrease, which that of thicker film gradually saturated. Therefore, it is concluded that the strain due to the lattice mismatch between substrate and film is fully relaxed around the thickness of 4000 .

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.1
• /
• pp.329-332
• /
• 2012

LEDs are using widely in a field of illumination, LCD LED backlight, mobile signals because they have several merits, such as low power consumption, long lifetime, high brightness, fast response, environment friendly. To achieve high performance LEDs, one needs to enhance output power, reduce operation voltage, and improve device reliability. In this paper, we have proposed that the optimum design and specialized process could improve the performance of LED chip. It was showed an output power of 7cd and input supplied voltage of 3.2V by the insertion technique of current blocking layer. In this paper, GaN-based LED chip which is built on the sapphire epi-wafer by selective MOCVD were designed and developed. After that, their performances were measured. It showed the output power of 7cd more than conventional GaN-based chip. It will be used the lighting source of a medical equipment and LCD LED TV with GaN-based LED chip.

• Tribology and Lubricants
• /
• v.32 no.4
• /
• pp.119-124
• /
• 2016

In the sapphire wafering process, lapping is a crucial operation in order to reduce the damaged layer and achieve the target thickness. Many parameters, such as pressure, velocity, abrasive, slurry and plate, affect lapping characteristics. This paper presents an experimental investigation on the effect of the plate groove on the material removal rate and roughness of the wafer. We select the spiral pattern and rectangular type as the groove shapes. We vary the groove density by controlling the groove shape dimension, i.e., the groove width and pitch. As the groove density increases to 0.4, the material removal rate increases and gradually reaches a saturation point. When the groove density is low, the pressing load is mostly supported by the thick film, and only a small amount acts on the abrasives resulting to a low material removal rate. The roughness decreases on increasing the groove density up to 0.3 because thick film makes partial participations of large abrasives which make deep scratches. From these results, we could conclude that the groove affects the contact condition between the wafer and plate. At the same groove density, the pitch has more influence on reducing the film thickness than the groove width. By decreasing the groove density with a smaller pitch and larger groove width, we could achieve a high material removal rate and low roughness. These results would be helpful in understanding the groove effects and determining the appropriate groove design.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.256-256
• /
• 2010

투명전극부터 디스플레이 산업에 이르기까지 광범위하게 응용되어지고 있고 개발되어지고 있는 투명전도산화물(TCO)은 ZnO, In2O3, SnO2 등을 기본으로 하는 n-type 재료가 대부분이다. 그러나 투명전도 산화물을 이용한 light emitting diode(LED), 투명한 태양전지, p-형 TFT와 같은 투명전자소자의 개발을 위해서는 p-type 소재가 필수적이다. p-type TCO 소재는 비교적 연구 개발 실적이 매우 부진한 실정이었다. 1997년 넓은 밴드갭을 가지는 ABO2(delafossite) 산화물이 p-type으로서 안정적이라는 것을 보고함에 따라 이에 대한 연구가 활발히 진행되고 있다. 현재 ABO2 형태를 가진 Delafossite구조 산화물이 가장 유망한 p-type 투명전도체 소재로 거론되고 있다. Delafossite 구조가 p-type 투명전도체에 적합한 결정구조인 이유는 밴드갭이 넓고 공유결합에 유리하기 때문이다. Delafossite구조는 상온에서 2종류의 polytype(상온에서 Rhombohedaral구조와 hexagonal 구조)이 존재하며 이들은 각각 3R 및 2H의 결정 구조를 가지고 있다. ABO2의 delafossite구조에서 Cu+의 배열은 c-축을 따라 Cu-O-Cr-O-Cu의 연속적인 층 구조로서 2차원연결로 보여 진다. 보고된 Cu- base delafossite구조를 가지는 재료들은 CuAlO2, CuGaO2, CuInO2 등 여러가지가 있다. 본 연구에서는 PLD를 이용하여 c-plane 사파이어 기판위에 성장된 delafossite구조인 CuCrO2박막의 특성을 알아보았다. p-type 특성을 위하여 CuCrO2에 Zn를 첨가하였으며 그에 따른 구조적 전기적 특성을 조사하였다. 성장온도와 산소분압을 $500{\sim}700^{\circ}C$, 0~10mTorr로 변화시켜 특성을 연구하였다. 성장온도 $700^{\circ}C$, 산소분압 10mTorr에서 c-plane 사파이어 기판위에 c-축 배향의 에피성장된 CuCrO2:Zn 박막을 얻을 수 있었다. Mg를 도핑함에 따른 p-type 특성보다 현저히 떨어지는 것을 확인하였다. 또한 동일한 조건임에도 특정한 이차상의 존재를 통해 도핑된 Zn의 위치를 추측할 수 있었다. 온도와 분압에 따른 결정성과 표면상태를 SEM을 통해서 확인하였다.