• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.577-578
• /
• 2006

In this paper, the rubber behavior was calculated for obtaining the optimal process condition which is for producing a transformer with a given performance. This study was carried out using the computer simulation of injection mold filling and packing simulations. In order to remove the crack of product, proper locations of the runner and cooling system configurations could be determined. Based on these results, the transformer is developed by injection molding and guidelines of part design, mold design and processing conditions are established. Finally, the cast savings, cycle time reduce and improvement of productivity will be obtained.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2005.05a
• /
• pp.252-257
• /
• 2005

Injection molding is a very important industrial process for the manufacturing of plastics objects. During an injection molding process of composites, the fiber-matrix separation and fiber orientation are caused by the flow of molten polymer/fiber mixture. As a result, the product tends to be nonhomogeneous and anisotropic. Hence, it is very important to clarify the relations between separation' orientation and injection molding conditions. So far, there is no research on the measurement of fiber orientation using image processing. In this study, the effects of fiber content ratio and molding condition on the fiber orientation-angle distributions are studied experimentally. Using the image processing method, the fiber orientation distribution of weld-line in injection-molded products is assessed. And the effects of fiber content and injection mold-gate conditions on the fiber orientation are also discussed.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2012.10a
• /
• pp.437-438
• /
• 2012

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2009.10a
• /
• pp.569-570
• /
• 2009

• Journal of Drive and Control
• /
• v.9 no.3
• /
• pp.56-66
• /
• 2012

• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.2
• /
• pp.216-222
• /
• 2013

This paper deals with the issue of kinematic modeling and analysis of a toggle mechanism. Based on the mathematic model of a conventional five-point type toggle mechanism. New five-point type toggle mechanism has been analyzed by computer simulation method. A sensitivity ratio has been defined and analyzed to compare its performance with four-point type toggle mechanism. A cycloidal motion has been applied to the cross head as an input and the motion of the moving platen is considered as an output. The effect of link design parameter as well as the type of toggle has been investigated by computer simulation to be available for industrial applications of injection molding machines.

• Journal of the Korean Society for Precision Engineering
• /
• v.31 no.2
• /
• pp.165-170
• /
• 2014

Reproducibility of injection molding machines are studied at the study of this time. We applied computer aided engineering program so it could generate clamping force, about 1,500 kN, to the nozzle center part of flex link in tie-bar and at this time, we made sure condition of stress distribution and transformation quantity in flex link. The result of computer aided engineering transformation quantity was confirmed that transformation of top area was 247~257 kN and bottom areas was 273~279 kN and also was confirmed that the stresses are distributed in a range of 57~750 $N/mm^2$ from top to the bottom of the surface. This time we could confirm the condition of transformation quantity and stress distribution by enforcing the previously used structure analysis of flex link. And we utilized the reference data to establish important point of section for non destructive test overhaul.

• Journal of Drive and Control
• /
• v.17 no.3
• /
• pp.15-25
• /
• 2020

The cycle time and power saving effect of a hydraulic hybrid injection molding machine using a servo motor are considered in this paper. In order to verify control characteristics, such as pressure and speed, experiments were performed with the hydraulic hybrid injection molding machine, clamping force of 110 ton. The power consumption and production cycle time of a conventional hydraulic injection molding machine were measured to compare its performances with the hydraulic hybrid injection molding machine. An injection molding machine with a clamping force of 1300 ton was used as the conventional machine, the hybrid machine was implemented by replacing its induction motors with servo motors. In the remodeled hybrid machine, experiments were performed to investigate how the displacement of the mold clamping pump affects the power consumption and production cycle time. The results showed that the production cycle time of the hybrid injection molding is similar to a conventional hydraulic injection molding machine but with a significant energy saving of about 40%.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.22 no.3
• /
• pp.328-333
• /
• 1993

The effect of defatted and dehydrated beef muscle on the physical properties of thermoplastically extruded defatted soybean, cottonseed, peanut and sunflower seed flours were investigated. To minimize the adverse effect of meat fat and to increase the mixing efficiency of the meat with defatted oilseed flours at a given moisture level, beef muscle was extracted with chloroform-ethanol(2 : 1) at 2$0^{\circ}C$ and air dried. The variety of oilseed flours used had greater effects on color, expansion, bulk density, water absorption rate and textural strength of the extrudate than did the added level of defatted, dehydrated beef muscle (0 to 20% on a dry weight basis).

• Proceedings of the Korea Institute of Fire Science and Engineering Conference
• /
• 2012.04a
• /
• pp.26-29
• /
• 2012

본 연구에서는 목분-폴리프로필렌 복합재의 연소성 및 열적특성을 평가하기 위하여 한계산소지수 실험 및 열중량 분석실험을 실시하였다. 목분-폴리프로필렌 복합재의 제조를 위하여 이축압출기를 활용한 압출공정과 사출성형기를 활용한 사출공정을 이용하였다. 그리고 복합재의 난연성능 향상을 위하여 난연제(4종류)를 첨가한 복합체의 화재성능을 평가하였다.