• Journal of Korean Society of Environmental Engineers
• /
• v.27 no.9
• /
• pp.946-951
• /
• 2005

In this wort plasma treatment was evaluated as an alternative clean desizing technology. Size materials such as PVA(polyvinyl alcohol), PACL(polyacrylic acid esters) and their mixture on PET(polyethylene terephthalate) fabrics were treated by $N_2$ and $O_2$ plasma. $O_2$ plasma was more efficient in size removal than $N_2$ plasma, and the removal of PVA was higher than that of PACL. SEM(scanning emission microscopy) pictures of the plasma treated samples directly proved the disappearance of sizing agents. After $O_2$ plasma treatment, the PET fabrics were subjected to conventional desizing process. Compared with untreated fabrics, the desizing effluent from the treated fabrics gave lower TOC, COD and $BOD_5$ values. This indicates plasma treatment not only serves to directly remove sizing agents but also offered several advantages by changing the chemical properties of sizing agents. Lastly, the effect of plasma desizing process on dyeing was examined using color difference and dyeing fastness tests. The CCM(computer color matching) results showed rotor difference between PET fabric desized by $O_2$ plasma treatment for 20 min and reference PET fabric desized by the conventional wet desizing process was around 1. This suggests the treated PET fabric can be directly subjected to dyeing process without any additional process. The plasma treated fabric also gave a good result of dyeing fastness so that grades of laundering, crocking, heat and light fastness were same or even better than the reference PET fabric did.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.405-405
• /
• 2012

에너지 갭의 크기가 큰 ZnO는 큰 여기자 결합과 높은 화학적 안정도를 가지고 있기 때문에 전자소자 및 광소자로 많이 응용되고 있다. ZnO는 광학적 및 전기적 성질의 여러 가지 장점 때문에 메모리, 나노발전기, 트랜지스터, 태양전지, 광탐지기 및 레이저와 같은 여러 분야에 많이 사용되고 있다. Zn와 쉘 구조가 비슷한 Cu 불순물은 우수한 luminescence activator이고 다양한 불순물 레벨을 만들기 때문에 전기적 및 광학적 특성을 변화하는데 좋은 도핑 물질이다. Cu가 도핑된 ZnO 나노구조를 전기화학적 증착법을 이용하여 형성하고, 형성시간의 변화에 따른 구조적 및 광학적 성질에 대한 관찰하였다. ITO 코팅된 유리 기판에 전기화학증착법을 이용하여 Cu 도핑된 ZnO를 성장하였다. Sputtering, pulsed laser vapor deposition, 화학기상증착, atomic layer epitaxy, 전자빔증발법 등으로 Cu 도핑된 ZnO 나노구조를 형성하지만 본 연구에서는 낮은 온도와 간단한 공정으로, 속도가 빠르고 가격이 낮아 경제적인 면에서 효율적인 전기 화학증착법으로 성장하였다. 반복실험을 통하여 Cu의 도핑 농도는 Zn과 Cu의 비율이 97:3이 되도록, ITO 양극과 Pt 음극의 전위차가 -0.75V로 실험조건을 고정하였고, 성장시간을 각각 5분, 10분, 20분으로 변화하였다. 주사전자현미경 사진에서 Cu 도핑된 ZnO는 성장 시간이 증가함에 따라 나노세선 형태에서 나노로드 형태로 변하였다. X-선 회절 측정결과에서 성장시간이 변화함에 따라 피크 위치의 변화를 관찰하였다. 광루미네센스 측정 결과는 Oxygen 공핍의 증가로 보이는 500~600 nm 대의 파장에서 나타난 피크의 위치가 에너지가 큰 쪽으로 증가하였다. 위 결과로부터 성장 시간에 따른 Cu 도핑된 ZnO의 구조적 및 광학적 특성변화를 관찰하였고, 이 연구 결과는 Cu 도핑된 ZnO 나노구조 기반 전자소자 및 광소자에 응용 가능성을 보여주고 있다.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.8 no.3
• /
• pp.129-141
• /
• 2005

It is difficult to edit large-scale digital maps because of problems of cost and process and it is carried out by aerial photogrammetry in renewal periods. Five years of update period cannot provide exact data required in the fast-moving age. This study is to analyze applicability and impact for editing digital map of road system using the GPS-Van. Results are compared with accuracy of the data acquisition with GPS-Van positioning. INS data are affected by the barrier to receive GPS data. But high accuracy were achieved by thorough plans according to work order. By using GPS Van and fieldwork at the same time for editing and renewal of digital map, it is expected that this method can be used to reduce costs in the economic and temporal aspects, and provide rapid and accurate digital map of road system.

• Journal of the Korean Vacuum Society
• /
• v.10 no.1
• /
• pp.27-30
• /
• 2001

Electromigration Phenomena in Al-1%Si thin film interconnections under DC and PDC conditions were investigated. Thin film interconnections with $SiO_2$ and PSG/$SiO_2$ dielectric passivation layer were formed by a standard photolithography process method and test line lengths were 100, 400, 800, 1200, and 1600 $\mu\textrm{m}$. The current density of $1.19\times10^7\textrm{A/cm}^2$ was stressed in Al-1%Si thin film interconnections under DC condition. The current density of $1.19\times10^7\textrm{A/cm}^2$ was also applied under PDC condition at the frequency of 1 Hz with the duty factor of 0.5. The electromigration resistance of PSG/SiO2 dielectric passivation test line was stronger than $SiO_2$ dielectric passivation test line. The lifetime under PDC was 2-4 times longer than DC condition. As the thin film interconnection line increased, the lifetime decreased and saturated over the critical length. Failure patterns by an electromigration were dominated by void-induced electrical open and hillock-induced electrical short.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.12
• /
• pp.1857-1863
• /
• 2010

We present the fabrication and characterization of transparent carbon nanotube film (CNF) piezoresistors. CNFs were fabricated by vacuum filtration methods with 65?92% transmittance and patterned on Au-deposited silicon wafer by photolithography and dry etching. The patterned CNFs were transferred onto poly-dimethysiloxane (PDMS) using the weak adhesion property between the silicon wafer and the Au layer. The transferred CNFs were confirmed to be piezoresistors using the equation of concentrated-force-derived resistance change. The gauge factor of the CNFs was measured to range from 10 to 20 as the resistance of the CNFs increased with applied pressure. In polymer microelectromechanical systems, CNF piezoresistors are the promising materials because of their high sensitivity and low-temperature process.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.28 no.5
• /
• pp.395-400
• /
• 2008

Alternating magnetic field was used for detection of surface flaws on nonmagnetic and magnetic metallic specimens. The nondestructive sensor probe was composed of the planar coil with inductive magnetic thin film yoke as a sensing component and a single straight typed exciting coil. The planar inductive coil sensor with magnetic yoke was fabricated by sputtering, electroplating, dry etching and photolithography process. The alternative currents with the range of 0.1A to 1.0A (0.7 MHz to 1.8 MHz) were applied to the exciting coil. The specimens were prepared with the slit shaped artificial surface flaws (minimum depth and width; 0.5 mm) on metallic plate (Al; nonmagnetic metal and FeC; magnetic metal). The detected signal for the positions and shapes of surface flaws on specimens were obtained with high sensitivity and high signal to ratio. The measured output signals by the non-contacted scanning on surface of FeC specimen with micron-sized crack were converted to the images of the flaws. And these results were compared with the optical images, respectively.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.28 no.5
• /
• pp.421-426
• /
• 2008

The magnetic bio-sensor used the PHR (planar hall resistance) effect generated by the free layer in spin-valve giant magnetoresistance structure of Ta/NiFe/CoFe/Cu/NiFe/IrMn/Ta. The PHR element with micrometer size was fabricated through the photolithograph and dry etching process. The PHR signal with magnetic field was measured under the conditions of with and without single magnetic bead. A single magnetic bead of diameter $2.8\;{\mu}m$ was successfully detected using the PHR sensor. Therefore, the high resolution PHR sensor can be applied to bio-sensor application utilizing the output voltage variation of the PHR signals in the presence and absence of a single magnetic bead.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.29 no.2
• /
• pp.141-147
• /
• 2011

This study analyzed the issues and its usefulness of drawing small-scale digital map by using the large-scale digital map which was producted with high-resolution digital aerial photograph which are commonly photographed in recent years. To this end, correlation analysis of the feature categories on the digital map was conducted, and this map was processed by inputting data, organizing, deleting, editing, and supervising feature categories according to the generalization process. As a result, 18 unnecessary feature codes were deleted, and the accuracy of 1/5,000 for the digital map was met. Although the size of the data and the number of feature categories increased, this was proven to be shown due to the excellent description of the digital aerial photograph. Accordingly, it was shown that drawing a small-scale digital map with the large-scale digital map by digital aerial photograph provided excellent description and high-quality information for digital map.

• Journal of the Korean Applied Science and Technology
• /
• v.29 no.3
• /
• pp.370-376
• /
• 2012

We fabricated linear low density polyethylene (LLDPE) particles via crystallization from decalin solution. In the thermally induced phase separation (TIPS) process, formation of particles occurred during controlled cooling of LLDPE/decalin solution. Despite an increase of nucleation and growth rate for crystals at higher polymer concentrations, which generally results in larger particles than at lower concentration, the average diameter of LLDPE particles increased as LLDPE was more concentrated in decalin solution. In the FE-SEM micrographs, the observed particles from various concentrations were smaller than 10 ${\mu}m$, showing spherical morphologies. In addition to its effect on size, concentration of LLDPE had an broadening effect on the particle size distribution.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2005.11a
• /
• pp.134-142
• /
• 2005

The experimental setups for flow visualization and processes identification in laboratory scale (so cal led Flow Lab.) has developed to get ideas and answer fundamental questions of flow and migration in geologic media. The setup was made of a granite block of $50{\times}50cm$ scale and a transparent acrylate plate. The tracers used in this experiments were tritiated water, anions, and sorbing cations as well as an organic dye, eosine, to visualize migration paths. The migration plumes were taken with a digital camera as a function of time and stored as digital images. A migration model was also developed to describe and identify the transport processes. Computer simulation was carried out not only for the hydraulic behavior such as distributions of pressure and flow vectors in the fracture but also for the migration plume and the elution curves.