• Proceedings of the KWS Conference
• /
• 2005.11a
• /
• pp.225-227
• /
• 2005

Sn-8wt%Zn-3wt%Bi (이하, Sn-8Zn-3Bi) 솔더의 장기 신뢰성을 평가하기 위하여 열 충격 시험을 행하였다. 열 충격 시험은 $-40^{\circ}C$에서 $80^{\circ}C$범위에서 1000 사이클 동안 하였다. 접합 기판으로는 각각 OSP(Organic Solderability Preservative), Sn 그리고 Ni/Au 처리를 한 PCB(Printed Circuit Board) 패드를 사용하였다. 접합에 사용한 부품은 1608 Chip(Multi Layer Chip Capacitor, Chip Resistor) 으로 전극 부위에 Sn-37wt%Pb, Sn 도금하여 사용하였다. 솔더링 후 1608 Chip의 전단 강도와 솔더링부에서 미세조직 및 IMC(Inter Metallic Compound) 변화를 관찰하였다. 측정결과, Sn-8Zn-3Bi 솔더의 초기 전단 강도는 기판의 표면처리에 상관없이 약 40N 이상이었다. 그리고 열충격 시험 1000 사이클 후에는 모든 기판에서 2N 정도 약간의 강도 저하를 보였다.

• Composites Research
• /
• v.14 no.5
• /
• pp.38-45
• /
• 2001

Kaiser effects of thermo-acoustic emission (AE) from composite laminates under the repetitive thermal cyclic loads have been quantitatively analyzed in consideration of AE source mechanisms. The repetitive thermal load brought about a large reduction. i.e. an exponential decrease in AE total ringdown counts and AE amplitudes. It was thought that generation of thermo-AE during the first thermal cycle was not caused by crack propagation but by secondary microfracturing due to abrasive contact between crack surfaces. For the repetitive thermal cycles, a few number of weak thermo-AE events were generated due to some frictional sliding contact. Such behavior of thermo-AE showed different characteristics according to specimen kinds and the maximum temperature in the thermal load cycles.

• Journal of Energy Engineering
• /
• v.21 no.4
• /
• pp.398-401
• /
• 2012

In this Study, efficiencies of the scroll expander under development for organic Rankine cycle using engine waste heat of vehicle have been analyzed and compared with the commercial scroll expander. While operating organic Rankine cycle for analysing expander efficiencies, power of expander, inlet temperature of expander, inlet pressure of expander and the flow rate of the working fluid(refrigerant R134a) have been measured. Overall efficiency of the expander has been shown the very low level compared with the overall efficiency of the commercial expander. Especially, because the low volumetric efficiency has much effect on overall efficiency, the working fluid leakage trouble of expander has to be solved surely for improvement of the expander overall efficiency.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.12 no.4_1
• /
• pp.23-32
• /
• 1992

The objective of this study is to identify the quantitative relationships among the important physical factors associated with failure of steel members under strong seismic excitations through very low-cycle fatigue tests. Very low-cycle fatigue is meant to be structural fatigue causing cracks and rupture in about 5~30 cycle ranges. The angle specimen was subjected to repeated axial Ioad after undergoing inelastic buckling. The test results reveal that the energy absorption capacities vary heavily with the history of loading and the failure mode. The maximum values of residual local strain at the initiation of a visible crack due to the very low-cycle fatigue were of the order of 25~40%, regardless of loading patterns, deflection modes, and width-to-thickness ratios.

• Journal of Energy Engineering
• /
• v.21 no.1
• /
• pp.26-32
• /
• 2012

This study has been performed Thermal Shock test for analyze the cause of Power drop in PV(Photovoltaic) Module. Thermal Shock test condition was performed with temperature range from $-40^{\circ}C{\sim}85^{\circ}C$. One cycle time is 30min. which are consist of low and high temperature 15min. each other. The test was performed with total 500cycles. EL, I-V were conducted every 100cycle up to 500cycles. Mono Cell resulted in 8% Power drop rates in Bare Cell and 9% in Solar Cell. In the case of Multi Cell resulted in 6% Power drop rates in Bare Cell and 13% in Solar Cell. After Thermal Shock test, Solar Cell's Power drop resulted from surface damages, but in the case of Bare Cell's Power drop had no surface damages. Therefore, Bare Cell's Power drop was confirmed as according to leakage current increase by analysis of Fill Factor after Thermal Shock test. Also, Solar Cell's Power drop rates are higher than that of Bare Cell because of surface damages and consuming electric power increase. From now on, it should be considered that analyzed the reasons of Fill Factor decrease and irregular Power drop in PV module and Cell level using cross section, various conditions and test methods.

• Composites Research
• /
• v.17 no.6
• /
• pp.52-57
• /
• 2004

In this study, mechanical tensile properties of carbon fiber reinforced polymeric (CFRP) composite cycled with thermo-mechanical loading under cryogenic temperature (CT) were measured using cryogenic environmental chamber. Thermo-mechanical tensile cyclic loading (up to 10 times) was applied to graphite/epoxy unidirectional laminate composites far room temperature (RT) to $-50^{\circ}C$, RT to $-100^{\circ}C$ and RT to $-150^{\circ}C$. Results showed that tensile stiffness obviously increased as temperature decreased while the thermo-mechanical cycling has little influence on it. Tensile strength, however, decreased as temperature down to CT while the reduction of strength showed little after CT-cycling. For the analysis of the test results, coefficient of thermal expansion (CTE) of laminate composite specimen at both RT and CT were measured and the interface between fiber and matrix was observed using SEM images.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.22 no.8
• /
• pp.1765-1773
• /
• 1997

The communication systems which include PLL may have cycle clip problem because of channel noise. The cycle slip problem occurs the synchronization loss of communication system and it may be fatal to the synchronous stream cipher system. While continuous resynchronization is used to lessen the risk of synchronization it has some problems. In this paper, we propose the method which solve the problems by using continuous resynchronization with the clock recovery technique. If the counted value of real clock pulse in reference duration is not same as that of normal state, we decide the cycle slip has occurred. The damaged clock by cycle slip is compensated by adding or subtracting the clock pulse according to the type of cycle slip. It reduced the time for resynchronization by twenty times. It means that 17.8% of data for transmit is compressed.

• Transactions of the KSME C: Technology and Education
• /
• v.1 no.1
• /
• pp.107-113
• /
• 2013

This paper presents the process of turbine development for Organic Rankine Cycle(ORC) system. Development of turbine for ORC system is hot issue in the electric generation market due to the characteristic of organic refrigerant which the evaporate temperature is lower than general refrigerant. Recently, the industry have an interest about ORC turbine development in Korea, and they presented numerous research results. In developing the turbine, several processes can be considered. However, there was few document about ORC turbine development because of the trade secret. This paper can be used as a reference in developing ORC turbine.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2000.11a
• /
• pp.4-4
• /
• 2000

KSR-III 과학로켓 개발사업의 한 분야인 추진기관 연구에 있어 가장 중심이 되는 것은 제작된 연소실의 시험/검증이라고 할 수 있다. 여러 단계의 시험 가운데에서도 엔진의 특성을 제 1차 적으로 파악하고, 시험 대상물인 엔진을 스탠드에 장착하여 시험이 가능토록 하기 위해서 모사 추진제(물) 혹은 실제 추진제를 사용하여 수력학적 특성을 알아내는 것은 매우 중요하다. 이를 위해 engineering model 엔진(이하 EM)에 대하여 액체 산소 배관은 액체 산소를, 스탠드 사정상 케로신 배관은 액체 질소를 사용한 비연소 시험을 수행하였으며, 이러한 일련의 비연소 시험을 통해 산화제 및 연료 매니폴드 각각에 대한 차압과 매니폴드를 채우는 시간을 측정하여 점화 사이클을 정의할 수 있었다.(중략)

• International Journal of Highway Engineering
• /
• v.6 no.3 s.21
• /
• pp.37-46
• /
• 2004

This study was performed to establish valid methodology for determining dynamic stability(DS) of deformation-cycle curve which is obtained through wheel tracking(WT) test, the most widely used method for forecast of rutting tendency of asphalt mixture. Existing Korean and Japanese methods for DS are unrealistic and do not really reflect characteristics of rut resistance of asphalt concretes especially when the slope of deformation-cycle curve is stabilized at the end. It was proved that the new DS developed in this study reflected rut resistance characteristics better than existing methods. It is especially effective to distinguish the mixtures with high DR(depth of rut) but stable slope at the end of curve from the mixture with lower DR and continuous slope. The field evaluation must be followed to prove whether the mixture which shows a high DS value this method perform well in the filed.